Effect of microporosity on nitrogen-doped microporous carbons for electrode of supercapacitor
Effect of microporosity on nitrogen-doped microporous carbons for electrode of supercapacitor
Carbon letters. 2014. Jul, 15(3): 210-213
Copyright © 2014, Korean Carbon Society
This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License ( which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : March 03, 2014
  • Accepted : May 05, 2014
  • Published : July 31, 2014
Export by style
Cited by
About the Authors
Eun-A Cho
Seul-Yi Lee
Soo-Jin Park
Nitrogen-doped microporous carbons were prepared using a polyvinylidene fluoride/melamine mixture. The electrochemical performance of the nitrogen-doped microporous carbons after being subjected to different carbonization conditions was investigated. The nitrogen to carbon ratio and specific surface area decreased with an increase in the carbonization temperature. However, the maximum specific capacitance of 208 F/g was obtained at a carbonization temperature of 800°C because it produced the highest microporosity.
1. Introduction
Supercapacitors are used for energy storage in various portable electronic devices and hybrid electric vehicles. They possess higher power and energy density, longer cycle life, and higher chemical stability compared to secondary batteries [1 - 3] . Recently, various carbon-based electrodes have been employed in supercapacitors because of their good electrical conductivity and large pseudocapacitance; however, they exhibit low capacitance values [4 - 6] . To improve their capacitance, nitrogen-containing functional groups are incorporated into the carbon materials. The pseudocapacitance originates from the interaction between the nitrogen species and protons of the electrolyte [7 - 10] .
Recent studies have revealed that mesopores and macropores in capacitor electrodes have limited capacitance [11 , 12] . The presence of narrow micropores is essential for the formation of an electrical double layer by solvated and desolvated ions. According to the literature, pore sizes ranging from 0.7-1.2 nm produce the optimum specific capacitance in aqueous electrolytes [13] . Therefore, producing microporous carbons with pore size in the abovementioned range is an effective way to improve the supercapacitor capacitance. Polyvinylidene fluoride (PVDF) is usually used as the polymer precursor for preparing the electrodes of supercapacitors. PVDF is converted to microporous carbon by carbonization without other activation methods. The microporous carbon has high specific surface area and potential. It also possesses narrow micropore distribution characteristics [14 - 17] . Melamine is a nitrogen rich compound, which is easy to handle. It is usually used for doping nitrogen functional groups. Nitrogen-enriched carbons possess high specific surface area and specific capacitance [18 - 21] . Nitrogen in melamine-derived carbons exists mainly in pyridinic, quaternary, and oxidized forms. The oxidized nitrogen is the most stable and the pyridinic nitrogen affects the electron donor-acceptor characteristics of the carbon materials, which leads to pseudocapacitive attraction between the protons of the electrolyte and the carbon electrode materials [22] . At a high carbonization temperature, more stable nitrogens are produced by the carbonization of melamine [23 , 24] .
In this study, nitrogen-functionalized microporous carbons were prepared by an activation-free method using the PVDF/melamine mixture as the carbon precursor. The effect of carbonization temperature on the electrochemical performance of the PVDF/melamine-based electrode is discussed.
2. Experimental
- 2.1. Materials and preparation
PVDF (Aldrich) and melamine (Aldrich) were used as the precursors for the nitrogen-functionalized microporous carbons. A mixture containing 1:0.5 ratio of the PVDF/melamine was put into a muffle furnace and was stabilized at 200°C in air for 2 h. Then, carbonization was carried out at 700-900°C for 2 h in a tubular furnace under nitrogen gas with a heating rate of 5°C/min and a nitrogen flow rate of 200 mL/min [6 , 25] . The samples were named PVDF/melamine 700, 800 and 900, where 700, 800, and 900 represent the carbonization temperature.
- 2.2. Measurements
The surface characterization was performed by elemental analysis (EA). The textural characteristics of the PMs were analyzed at 77 K using a gas adsorption analyzer (BELSORP, BEL Japan). The specific surface areas and micropore volumes of the samples were determined from the Brunauer-Emmett-Teller (BET) and Dubinin-Radushkevich (D-R) equations. The electrochemical performance was characterized by cyclic voltammetry (CV) and galvanostatic charge/discharge measurements using a three-electrode electrochemical cell. The threeelectrode cell consisted of a Pt wire as the counter electrode, Ag/AgCl as the reference electrode, and Ni foam coated with the samples as the working electrode. The specific capacitances of the samples studied were estimated according to the following Eq. (1) [26 , 27] :
PPT Slide
Lager Image
where C is the capacitance of the cell, I the discharge current, Δ t the discharge time, Δ V the voltage range, and m the mass of the active material on the electrode [28 - 30] .
3. Results and Discussion
PVDF was used to obtain porous carbons by carbonization in the absence of an activation process. The specific surface area and pore volume of the samples studied were determined by nitrogen adsorption/desorption isotherms at 77 K. The textural properties determined by the BET results are shown in Table 1 . The decrease in the specific surface area of the samples studied is attributed to the effect of carbonization temperature. The total pore volume also decreased. Therefore, the formation of the micropores could be easily controlled by the carbonization process. However, the highest micropore volume was obtained at 800°C. The PVDF/melamine 800 had the highest micropore volume (0.2202 cm 3 /g) and the lowest mesopore volume (0.1274 cm 3 /g), which is probably due to poor carbonization at the low temperature and the collapse of the micropores at the high temperature.
The surface characteristics of the samples studied were analyzed by EA. As shown in Table 1 , the content of nitrogen groups on the PVDF/melamine 700, 800, and 900 are 14.9, 13.4, and 12.9%, respectively. The nitrogen content decreased with the increasing carbonization temperature. The PVDF/melamine 900 has the lowest nitrogen content (12.9%), which is probably due to the volatilization of the N/C species at elevated carbonization temperatures [31] .
Fig. 1 shows the CV of the samples studied using 6.0 M potassium hydroxide electrolyte solution at the scan rate 50 mV/s in the voltage range of -0.6 V to 0.0 V. The CV curves are symmetric rectangular in shape and exhibit a larger peak area, which shows that the sample has a high specific capacitance. The largest CV curve obtained was for the PVDF/melamine 800, which shows that it has a greater current density than the other samples studied, resulting from the micropore volume ( Table 1 ).
PPT Slide
Lager Image
Cyclic voltammetry of samples studied at 50 mV/s. PVDF: polyvinylidene fluoride.
Chemical compositions and textural properties of the samples studied
PPT Slide
Lager Image
BET: Brunauer-Emmett-Teller, PVDF: polyvinylidene fluoride. a)Specific surface area (m2g-1). b)Total pore volume (cm3g-1). c)Mesopore volume (cm3g-1). d)Micropore volume (cm3g-1). e)(Micropore volume/total pore volume) × 100 (%). f)Content of carbon (at%). g)Content of nitrogen (at%). h)Content of nitrogen/content of carbon.
Fig. 2 shows the galvanostatic charge/discharge curve at a loading current of 1 A/g. The galvanostatic charge/discharge curve is linear triangular in shape. The curve for the PVDF/ melamine 800 shows the largest peak and the longest discharge time. The specific capacitance is calculated from the discharge curve ( Fig. 2 ); and it indicates 156, 205 and 139 F/g on the PVDF/melamine 700, 800 and 900. The PVDF/melamine 800 exhibited the highest specific capacitance (205 F/g). The specific capacitances of the samples studied are dependent on the carbonization temperature, which in turn can control the pore size of the carbon and the contents of the polar doping groups. The increase in capacitance is attributed to the added micropores. The nitrogen-doped microporous carbon exhibited enhanced electrochemical performance when prepared at the carbonization temperature of 800°C, and demonstrated superior electrochemical supercapacitor and pseudocapacitive behaviors [32] .
PPT Slide
Lager Image
Charge/discharge behavior of samples studied at 1 A/g. PVDF: polyvinylidene fluoride.
4. Conclusions
In this study, nitrogen-functionalized microporous carbons were prepared by carbonization of a PVDF/melamine mixture without an activation process. The nitrogen contents decreased with increasing carbonization temperatures. However, the micropore volume of the PVDF/melamine 800 was greater than that of the PVDF/melamine 700. The PVDF/melamine 800 sample had a maximum specific capacitance of 205 F/g with a large micropore volume of 0.2202 cm 3 /g. Thus, we found that the microporosity of the PVDF/melamine can be attributed to preparation at an optimum carbonization temperature, resulting in the easy transfer and excellent accessibility of the electrolyte ions in the nitrogen-functionalized carbon electrodes.
This research was supported by the Carbon Valley Project of the Korea Government (Ministry of Commerce, Industry and Energy) and Korea Ministry of Environment (MOE) as “GAIA Program”.
Inagaki M , Kang F , Toyoda M , Konno H. , Inagaki M , Kang F , Toyoda M , Konno H 2014 Advanced Materials Science and Engineering of Carbon Butterworth-Heinemann Boston, MA Carbon materials for electrochemical capacitors 237 -
Frackowiak E , Béguin F 2001 Carbon materials for the electrochemical storage of energy in capacitors Carbon 39 937 -
Ma C , Song Y , Shi J , Zhang D , Zhai X , Zhong M , Guo Q , Liu L 2013 Preparation and one-step activation of microporous carbon nanofibers for use as supercapacitor electrodes Carbon 51 290 -
Chen XY , Chen C , Zhang ZJ , Xie DH , Deng X , Liu JW 2013 Nitrogendoped porous carbon for supercapacitor with long-term electrochemical stability J Power Sources 230 50 -
Qin CL , Lu X , Yin GP , Bai XD , Jin Z 2009 Activated nitrogen-enriched carbon/carbon aerogel nanocomposites for supercapacitor applications Trans Nonferrous Metals Soc China 19 s738 -
Kim KS , Park SJ 2011 Synthesis of nitrogen doped microporous carbons prepared by activation-free method and their high electrochemical performance Electrochim Acta 56 10130 -
Li W , Chen D , Li Z , Shi Y , Wan Y , Wang G , Jiang Z , Zhao D 2007 Nitrogen-containing carbon spheres with very large uniform mesopores: the superior electrode materials for EDLC in organic electrolyte Carbon 45 1757 -
Guo P , Gu Y , Lei Z , Cui Y , Zhao XS 2012 Preparation of sucrose-based microporous carbons and their application as electrode materials for supercapacitors Microporous Mesoporous Mater 156 176 -
Kim KS , Park SJ 2012 Synthesis and high electrochemical capacitance of N-doped microporous carbon/carbon nanotubes for supercapacitor J Electroanal Chem 673 58 -
Hulicova D , Yamashita J , Soneda Y , Hatori H , Kodama M 2005 Supercapacitors prepared from melamine-based carbon Chem Mater 17 1241 -
Chen J , Jia C , Wan Z 2014 Novel hybrid nanocomposite based on poly(3,4-ethylenedioxythiophene)/multiwalled carbon nanotubes/graphene as electrode material for supercapacitor Synth Met 189 69 -
Ma C , Li Y , Shi J , Song Y , Liu L 2014 High-performance supercapacitor electrodes based on porous flexible carbon nanofiber paper treated by surface chemical etching Chem Eng J 249 216 -
Kitajima M , Sato M , Nishide H 2013 Preparation of flat porous carbon films from paper-thin wood shavings and control of their mechanical, electrical and magnetic properties Carbon 61 260 -
Pan Y , Mei Z , Yang Z , Zhang W , Pei B , Yao H 2014 Facile synthesis of mesoporous MnO2/C spheres for supercapacitor electrodes Chem Eng J 242 397 -
Lota G , Lota K , Frackowiak E 2007 Nanotubes based composites rich in nitrogen for supercapacitor application Electrochem Commun 9 1828 -
Chen T , Dai L 2013 Carbon nanomaterials for high-performance supercapacitors Mater Today 16 272 -
Swietlik U , Grzyb B , Torchala K , Gryglewicz G , Machnikowski J 2014 High temperature ammonia treatment of pitch particulates and fibers for nitrogen enriched microporous carbons Fuel Process Technol 119 211 -
Su F , Zeng J , Yu Y , Lv L , Lee JY , Zhao XS 2005 Template synthesis of microporous carbon for direct methanol fuel cell application Carbon 43 2366 -
Leżańska M , Olejniczak A , Pacula A , Szymański G , Wloch J 2014 The influence of microporosity creation in highly mesoporous N-containing carbons obtained from chitosan on their catalytic and electrochemical properties Catal Today 227 223 -
Lee SY , Park SJ 2014 Carbon dioxide adsorption performance of ultramicroporous carbon derived from poly(vinylidene fluoride) J Anal Appl Pyrolysis 106 147 -
Zheng C , Zhou X , Cao H , Wang G , Liu Z 2014 Synthesis of porous graphene/activated carbon composite with high packing density and large specific surface area for supercapacitor electrode material J Power Sources 258 290 -
Chen XY , Xie DH , Chen C , Liu JW 2013 High-performance supercapacitor based on nitrogen-doped porous carbon derived from zinc(II)-bis(8-hydroxyquinoline) coordination polymer J Colloid Interface Sci 393 241 -
Si W , Zhou J , Zhang S , Li S , Xing W , Zhuo S 2013 Tunable N-doped or dual N, S-doped activated hydrothermal carbons derived from human hair and glucose for supercapacitor applications Electrochim Acta 107 397 -
Im JS , Park SJ , Lee YS 2007 Preparation and characteristics of electrospun activated carbon materials having meso- and macropores J Colloid Interface Sci 314 32 -
Khairnar V , Jaybhaye S , Hu CC , Afre R , Soga T , Sharon M , Sharon M 2008 Development of supercapacitors using porous carbon materials synthesized from plant derived precursors Carbon Lett 9 188 -
Xu B , Hou S , Zhang F , Cao G , Chu M , Yang Y 2014 Nitrogen-doped mesoporous carbon derived from biopolymer as electrode material for supercapacitors J Electroanal Chem 712 146 -
Mehmani A , Prodanovic M 2014 The effect of microporosity on transport properties in porous media Adv Water Resour 63 104 -
Chen A , Liu C , Yu Y , Hu Y , Lv H , Zhang Y , Shen S , Zhang J 2014 A co-confined carbonization approach to aligned nitrogen-doped mesoporous carbon nanofibers and its application as an adsorbent J Hazard Mater 276 192 -
Guo Z , Zhou Q , Wu Z , Zhang Z , Zhang W , Zhang Y , Li L , Cao Z , Wang H , Gao Y 2013 Nitrogen-doped carbon based on peptides of hair as electrode materials for surpercapacitors Electrochim Acta 113 620 -
Lezanska M , Olejniczak A , Pacula A , Szymanski G , Wloch J 2014 The influence of microporosity creation in highly mesoporous N-containing carbons obtained from chitosan on their catalytic and electrochemical properties Catal Today 227 223 -
Del Regno A , Siperstein FR 2013 Organic molecules of intrinsic microporosity: characterization of novel microporous materials Microporous Mesoporous Mater 176 55 -
Prasad KPS , Dhawale DS , Joseph S , Anand C , Wahab MA , Mano A , Sathish CI , Balasubramanian VV , Sivakumar T , Vinu A 2013 Postsynthetic functionalization of mesoporous carbon electrodes with copper oxide nanoparticles for supercapacitor application Microporous Mesoporous Mater 172 77 -