In this work, nanocomposites of epoxy resin and chemically reduced graphene oxide (RGO) were prepared by thermal curing process. X-ray diffractions confirmed the microstructural properties of RGO. Differential scanning calorimetry was used to evaluate the curing behaviors of RGO/epoxy nanocomposites with different RGO loading amounts. We investigated the effect of RGO loading amounts on the mechanical properties of the epoxy nanocomposites. It was found that the presence of RGO improved both flexural strength and modulus of the epoxy nanocomposites till the RGO loading reached 0.4 wt%, and then decreased. The optimum loading achieved about 24.5 and 25.7% improvements, respectively, compared to the neat-epoxy composites. The observed mechanical reinforcement might be an enhancement of mechanical interlocking between the epoxy matrix and RGO due to the unique planar structures.
1. Introduction
Graphene, the thinnest known material in the cosmos, exhibits many outstanding properties, like extremely high strength (~130 GPa) and modulus (~1000 GPa)
[1]
, high thermal conductivity (~5000 W/(m
3
∙K))
[2]
, and very high electrical conductivity (~6000 S/cm)
[3]
, all due to its sp
2
-hybridized carbon atoms.
There have been many studies on graphene synthesis methods; the most common synthesis method is a top-down processing of graphite to graphene oxide (GO) by strong oxidation and mechanical exfoliation
[4]
. GO is an insulator by nature due to an abundance of oxygen-functional groups, but it can be reduced chemically or thermally to form electrically conductive graphene materials.
Graphene has been used as a nanofiller in a wide range of polymer matrices including polystyrene
[5]
, polyurethane
[6]
, polypropylene
[7]
, polycarbonate
[8]
, poly(vinyl alcohol)
[9]
, and so on. Graphene based nanocomposites have been investigated for their superior electrical, thermal, and mechanical properties
[10
-
12]
. The incorporation of various nano-sized reinforcements into an epoxy matrix can maximize the advantages of structural composites
[13
-
15]
. Remarkable improvements in physical and mechanical properties of polymer composites have been reported upon the addition of a small amount of graphene
[16
-
18]
.
In order to enhance the properties of graphene based nanocomposites, improving the dispersion of the graphene in polymer has remained the most important issue to be resolved. It is well known that graphene will normally become entangled due to intermolecular van der Waals forces and will aggregate in the polymer matrix. The resulting poor dispersion of graphene significantly lowers its efficiency as a reinforcement, and in particular, can lead to a different impact on the mechanical properties of polymer composites. A variety of processing methods, including in situ polymerization, melt mixing, and solution blending, have been proposed to disperse graphene in polymer matrix
[19
,
20]
.
In this work, we prepared chemically reduced GO (RGO) for use as a mechanically enhancing filler in an epoxy matrix. The nanocomposites of epoxy resin with RGO were prepared by thermal curing process. The flexural properties of the RGO/ epoxy nanocomposites were investigated as a function of RGO loading amount.
2. Experimental
- 2.1. Materials and sample preparation
GO was produced using the Hummers’ method as a starting material for graphene
[21]
. The chemically reduced GO was prepared as follows: 1) 1 g of GO was dispersed into distilled water using ultra-sonication; 2) 1 g of hydroquinone was added to the GO solution, and the mixture was heated to 150℃ for 24 h; 3) the GO solution was thoroughly dried at 80℃ in a vacuum oven after washing with distilled water and ethanol at a ratio of 1:1.
The epoxy polymer used in this study was diglycidyl ether of bisphenol A, supplied by Kukdo Chem. of Korea (YD-128, an epoxide equivalent weight of 185-190 g/eq, a density of approximately 1.16 g/cm
3
at 25℃). 4,4›-Diaminodiphenyl methane was used as a curing agent for the epoxy polymer. The epoxy polymer and RGO powder were fed into a beaker, with ultra-sonication at 80℃ for 12 h to enhance the dispersion state of the RGO in the epoxy matrix. The composites were mixed with RGO at the weight percent loading range of 0-0.5 wt%. The stoichiometric amount of curing agent was added to the RGO/ epoxy mixtures. The mixtures were poured into a designed mold and degassed at 120℃ for 20 min in a vacuum oven. Then, the curing processes were performed, at 120℃ for 1 h and 150℃ for 2 h. Finally, samples were post-cured at 180℃ for 1 h in a convection oven.
- 2.2. Characterization
The micro-structural characteristics of the GO and RGO were investigated using X-ray diffraction (XRD, Model D2 Phaser, BRUKER Co.). The curing behaviors were monitored by differential scanning calorimetry (DSC, Model DSC 200, NETZSCH Co.) from 50 to 250℃ at a heating rate of 10℃/min under an N
2
flow. The flexural properties were measured by an Instron universal testing machine (UTM, Model LR5K, LLOYD Co.) according to ASTM D-790. The average values were obtained from the results of five tests. The fracture surfaces of RGO/epoxy composites after the flexural stress test were observed by scanning electron microscopy (SEM, Model S-4200, Hitachi Co.).
3. Results and Discussion
XRD patterns of graphite showed an intensive diffraction (002) peak at 2 theta = 26.6°, reflecting a
d
-spacing of 3.35 Å between the graphitic interlayers. It was found that a well-defined diffraction peak of GO was observed at 2 theta = 12.8°, indicating that the interlayer spacing or gap increased to 6.91 Å. After the chemical reduction, the asymmetric diffraction peak of RGO was revealed at around 2 theta = 11°and 24°. This result confirmed that the RGO were exfoliated into stacking layered sheets.
Wide X-ray diffraction patterns of graphite (a), graphene oxide (GO) (b), and reduced GO (RGO) synthesized in this study (c).
DSC curves of the RGO/epoxy mixtures are shown in
Fig. 2
, Grapheneinvestigating the curing behaviors of the RGO/epoxy nanocomposites. All samples showed a single exothermic peak at a high temperature, more than 150℃, originating from the decomposition of functional groups in the epoxy-based composites
[18]
. The main exothermic peaks of RGO/epoxy nanocomposites were observed to be at a higher temperature than those for neat-epoxy composites. It was confirmed that this was due to the steric hindrance effect on the curing process with the addition of RGO particles. The higher volume fraction of RGO increased the surface area in contact with the epoxy matrix, which could anchor the chain mobility
[22
23]
.
Differential scanning calorimetry curves of reduced graphene oxide (RGO)/epoxy nanocomposites with different RGO loading amounts.
The effect of the RGO loading amounts on the mechanical properties of RGO/epoxy nanocomposites was investigated with flexural measurements. As shown in
Fig. 3
, the enhancement effect produced by the presence of RGO can be clearly distinguished. The flexural properties increased with increasing RGO loading amounts up to 0.4 wt%, and then decreased. The flexural strength and modulus of RGO-0.4 was determined to be 102 and 2210 MPa, respectively. It was found that the enhancement of flexural properties was strongly related to the interfacial adhesion between the RGO and epoxy matrix. The overloading of RGO (RGO-0.5) produced poor flexural properties, resulting from the aggregation of RGO in the epoxy matrix. Excessive interfacial contacts, between both the RGO/RGO and RGO/matrix, weaken the flexural properties of RGO/epoxy nanocomposites
[24]
. From the results, we found that the appropriate amount of RGO led to a superior reinforcement effect in the matrix.
Flexural strength and modulus of graphene oxide (RGO)/epoxy composites with different RGO loading amounts.
To understand the influence of added RGO on the mechanical properties of the epoxy nanocomposites, the fracture surfaces of the samples after impact tests were characterized with SEM, as shown in
Fig. 4
. A smooth surface (
Fig. 4
) was observed in the RGO-0 sample. The fracture surfaces of the RGO/epoxy nanocomposites appeared rougher and more varied in comparison with RGO-0, indicating that higher fracture energy was required
[25
,
26]
. However, the sample with excessive RGO loading, RGO-0.5, exhibited an agglomeration of RGO and some defects in the matrix. It was found that in this case the RGO had acted as stress concentrators and reduced the strengthening effects of RGO in the matrix
[26]
.
Scanning electron microscope images of graphene oxide (RGO)/epoxy nanocomposites; (a) RGO-0, (b) RGO-0.1, (c) RGO-0.2, (d) RGO-0.3, (e) RGO- 0.4, and (f ) RGO-0.5.
4. Conclusions
In this work, we prepared chemically RGO for use as a mechanically enhancing filler in an epoxy matrix. The mechanical properties of the RGO/epoxy nanocomposites were investigated as a function of RGO loading amount. From the results, it was found that the flexural strength and modulus of RGO/epoxy nanocomposites were ~24.5% and ~25.7% greater, respectively, than those of the neat epoxy composites, when the added RGO amount was 0.4 wt% .
Acknowledgements
This research was financially supported by the Ministry of Education, Science Technology (MEST) and National Research Foundation of Korea (NRF) through the Human Resource Training Project for Regional Innovation (No. 2012-10-A-04-046-13- 010100).
Lee C
,
Wei X
,
Kysar JW
,
Hone J
2008
Measurement of the elastic properties and intrinsic strength of monolayer graphene
Science
http://dx.doi.org/10.1126/science.1157996
321
385 -
Balandin AA
,
Ghosh S
,
Bao W
,
Calizo I
,
Teweldebrhan D
,
Miao F
,
Lau CN
2008
Superior thermal conductivity of single-layer graphene
Nano Lett
http://dx.doi.org/10.1021/nl0731872
8
902 -
Du X
,
Skachko I
,
Barker A
,
Andrei EY
2008
Approaching ballistic transport in suspended graphene
Nat Nanotechnol
http://dx.doi.org/10.1038/nnano.2008.199
3
491 -
Lee SY
,
Park SJ
2012
Comprehensive review on synthesis and adsorption behaviors of graphene-based materials
Carbon Lett
http://dx.doi.org/10.5714/CL.2012.13.2.073
13
73 -
Stankovich S
,
Dikin DA
,
Dommett GHB
,
Kohlhaas KM
,
Zimney EJ
,
Stach EA
,
Piner RD
,
Nguyen ST
,
Ruoff RS
2006
Graphene-based composite materials
Nature
http://dx.doi.org/10.1038/nature04969
442
282 -
Jung YC
,
Kim JH
,
Hayashi T
,
Kim YA
,
Endo M
,
Terrones M
,
Dresselhaus MS
2012
Fabrication of transparent, tough, and conductive shape-memory polyurethane films by incorporating a small amount of high-quality graphene
Macromol Rapid Commun
http://dx.doi.org/10.1002/marc.201100674
33
628 -
Song P
,
Cao Z
,
Cai Y
,
Zhao L
,
Fang Z
,
Fu S
2011
Fabrication of exfoliated graphene-based polypropylene nanocomposites with enhanced mechanical and thermal properties
Polymer
http://dx.doi.org/10.1016/j.polymer.2011.06.045
52
4001 -
Potts JR
,
Murali S
,
Zhu Y
,
Zhao X
,
Ruoff RS
2011
Microwave-exfoliated graphite oxide/polycarbonate composites
macromolecules
http://dx.doi.org/10.1021/ma2007317
44
6488 -
Salavagione HJ
,
Martínez G
,
Gómez MA
2009
Synthesis of poly(vinyl alcohol)/reduced graphite oxide nanocomposites with improved thermal and electrical properties
J Mater Chem
http://dx.doi.org/10.1039/b904232f
19
5027 -
Shiu SC
,
Tsai JL
2014
Characterizing thermal and mechanical properties of graphene/epoxy nanocomposites
Composites B
http://dx.doi.org/10.1016/j.compositesb.2013.09.007
56
691 -
Wang X
,
Jin J
,
Song M
2013
An investigation of the mechanism of graphene toughening epoxy
Carbon
http://dx.doi.org/10.1016/j.carbon.2013.08.032
65
324 -
Castelain M
,
Martínez G
,
Ellis G
,
Salavagione HJ
2013
A versatile chemical tool for the preparation of conductive graphene-based polymer nanocomposites
Chem Commun
http://dx.doi.org/10.1039/c3cc43729a
49
8967 -
Liang J
,
Huang Y
,
Zhang L
,
Wang Y
,
Ma Y
,
Guo T
,
Chen Y
2009
Molecular-level dispersion of graphene into poly(vinyl alcohol) and effective reinforcement of their nanocomposites
Adv Funct Mater
http://dx.doi.org/10.1002/adfm.200801776
19
2297 -
Sánchez M
,
Campo M
,
Jiménez-Suárez A
,
Ureña A
2013
Effect of the carbon nanotube functionalization on flexural properties of multiscale carbon fiber/epoxy composites manufactured by VARIM
Composites B
http://dx.doi.org/10.1016/j.compositesb.2012.09.063
45
1613 -
Lv S
,
Ma Y
,
Qiu C
,
Sun T
,
Liu J
,
Zhou Q
2013
Effect of graphene oxide nanosheets of microstructure and mechanical properties of cement composites
Constr Build Mater
http://dx.doi.org/10.1016/j.conbuildmat.2013.08.022
49
121 -
Feng H
,
Wang X
,
Wu D
2013
Fabrication of spirocyclic phosphazene epoxy-based nanocomposites with graphene via exfoliation of graphite platelets and thermal curing for enhancement of mechanical and conductive properties
Ind Eng Chem Res
http://dx.doi.org/10.1021/ie400483x
52
10160 -
Wan YJ
,
Tang LC
,
Yan D
,
Zhao L
,
Li YB
,
Wu LB
,
Jiang JX
,
Lai GQ
2013
Improved dispersion and interface in the graphene/epoxy composites via a facile surfactant-assisted process
Composites Sci Technol
http://dx.doi.org/10.1016/j.compscitech.2013.04.009
82
60 -
Li Z
,
Wang R
,
Young RJ
,
Deng L
,
Yang F
,
Hao L
,
Jiao W
,
Liu W
2013
Control of the functionality of graphene oxide for its application in epoxy nanocomposites
Polymer
http://dx.doi.org/10.1016/j.polymer.2013.09.054
54
6437 -
Kuilla T
,
Bhadra S
,
Yao D
,
Kim NH
,
Bose S
,
Lee JH
2010
Recent advances in graphene based polymer composites
Prog Polym Sci
http://dx.doi.org/10.1016/j.progpolymsci.2010.07.005
35
1350 -
Tang LC
,
Wan YJ
,
Yan D
,
Pei YB
,
Zhao L
,
Li YB
,
Wu LB
,
Jiang JX
,
Lai GQ
2013
The effect of graphene dispersion on the mechanical properties of graphene/epoxy composites
Carbon
http://dx.doi.org/10.1016/j.carbon.2013.03.050
60
16 -
Hummers WS
,
Offeman RE
1958
Preparation of graphitic oxide
J Am Chem Soc
http://dx.doi.org/10.1021/ja01539a017
80
1339 -
Jiang T
,
Kuila T
,
Kim NH
,
Ku BC
,
Lee JH
2013
Enhanced mechanical properties of silanized silica nanoparticle attached graphene oxide/epoxy composites
Composites Sci Technol
http://dx.doi.org/10.1016/j.compscitech.2013.02.018
79
115 -
Fang M
,
Zhang Z
,
Li J
,
Zhang H
,
Lu H
,
Yang Y
2010
Constructing hierarchically structured interphases for strong and tough epoxy nanocomposites by amine-rich graphene surfaces
J Mater Chem
http://dx.doi.org/10.1039/c0jm01620a
20
9635 -
Li Z
,
Young RJ
,
Wang R
,
Yang F
,
Hao L
,
Jiao W
,
Liu W
2013
The role of functional groups on graphene oxide in epoxy nanocomposites
Polymer
http://dx.doi.org/10.1016/j.polymer.2013.08.026
54
5821 -
Lim SR
,
Chow WS
2011
Fracture toughness enhancement of epoxy by organo-montmorillonite
Polym Plast Technol Eng
http://dx.doi.org/10.1080/03602559.2010.531427
50
182 -
Shen J
,
Huang W
,
Wu L
,
Hu Y
,
Ye M
2007
The reinforcement role of different amino-functionalized multi-walled carbon nanotubes in epoxy nanocomposites
Composites Sci Technol
http://dx.doi.org/10.1016/j.compscitech.2007.04.025
67
3041 -