Synthesis and Electrochemical Performance of Polypyrrole-Coated Iron Oxide/Carbon Nanotube Composites
Synthesis and Electrochemical Performance of Polypyrrole-Coated Iron Oxide/Carbon Nanotube Composites
Carbon letters. 2012. Jul, 13(3): 157-160
Copyright ©2012, Korean Carbon Society
This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License ( by-nc/3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : April 11, 2012
  • Accepted : May 21, 2012
  • Published : July 31, 2012
Export by style
Cited by
About the Authors
Dae-Won, Kim
Korea CCS R&D Center, Korea Institute of Energy Research, Daejeon 305-343, Korea
Ki-Seok, Kim
Korea CCS R&D Center, Korea Institute of Energy Research, Daejeon 305-343, Korea
Soo-Jin, Park
Korea CCS R&D Center, Korea Institute of Energy Research, Daejeon 305-343, Korea

In this work, iron oxide (Fe 3 O 4 ) nanoparticles were deposited on multi-walled carbon nanotubes (MWNTs) by a simple chemical coprecipitation method and Fe 3 O 4 -decorated MWNTs (Fe-MWNTs)/polypyrrole (PPy) nanocomposites (Fe-MWNTs/PPy) were prepared by oxidation polymerization. The effect of the PPy on the electrochemical properties of the Fe- MWNTs was investigated. The structures characteristics and surface properties of MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy were characterized by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. The electrochemical performances of MWNTs, Fe- MWNTs, and Fe-MWNTs/PPy were determined by cyclic voltammetry and galvanostatic charge/discharge characteristics in a 1.0 M sodium sulfite electrolyte. The results showed that the Fe-MWNTs/PPy electrode had typical pseudo-capacitive behavior and a specific capacitance significantly greater than that of the Fe-MWNT electrode, indicating an enhanced electrochemical performance of the Fe-MWNTs/PPy due to their high electrical properties.
1. Introduction
Electrochemical capacitors or supercapacitors have attracted increased interest due to their high power density compared to that of conventional capacitors [1 - 3] . Electrochemical capacitors have been developed to provide power pulses for a wide range of application areas including transportation, consumer electronics, medical electronics, and military devices [4] . According to the energy storage mechanism, two kinds of electrochemical capacitors have been examined: 1) electric double layer capacitors (EDLC) using carbon having a very high surface area as the electrode material [5] ; 2) conducting polymers [6] or metal oxide based pseudo-capacitors [7] .
In pseudo-capacitors, charge is stored by the electrical charge transport in redox reaction on the electroactive species. These species in pseudo-capacitors formed metal oxides and conducting polymers on the electrode surface, accelerating the redox reactions [8 , 9] .
Polypyrrole (PPy) is one of the most important conducting polymers; it is used in a wide range of applications owing to its relatively facile processability, mechanical flexibility, low cost, electrical conductivity, and thermal and chemical stability [10] .
Carbon nanotubes (CNTs), as EDLC electrode materials, have attracted much attention because of their high electrical conductivity, unique entangled network, and dominant porous character [11] . Nowadays, significant interest has been generated in research that mixes CNTs with various inorganic and organic substances by physical and chemical approaches to prepare multifunctional composites. A variety of CNT composites have been prepared and investigated [12 , 13] . Recently, extensive efforts have been made to prepare functional PPy- CNT composites that exhibit enhanced electrical, thermal or mechanical properties relative to PPy or to CNTs alone [14] .
Much research on supercapacitors is aimed at increasing both the power and the energy densi-ty as well as lowering fabrication costs while using environmentally friendly materials. The development of advanced composite materials based on the use of metal oxide-carbon nanotubes for supercapacitor electrodes has been studied in the hope that these materials can provide improved capacitive behaviors due to their enhanced stability, high conductivity, and pseudo-capacitance [15 , 16] .
In this work, a novel PPy-coated Fe 3 O 4 / multi-walled CNT (MWNT) nanoparticle composite (Fe-MWNT/PPy) has been prepared by the coprecipitation of Fe3+ and Fe 2+ and the in situ polymerization of pyrrole. The characterization and electrochemical performance of Fe-MWNTs/Ppy are performed to determine its potential use as a supercapacitor electrode.
2. Experimental
- 2.1. Materials
MWNTs produced via chemical vapor deposition method were purchased from Nano Solution Co. (Korea, degree of purity: ≥95 wt%, diameter; 10-25 nm, length: 10-50 μm). Ferric chloride (FeCl 3 ·6H 2 O), ferrous chloride (FeCl 2 ·4H 2 O), pyrrole, ammonium persulfate (APS), and ammonium hydroxide aqueous solution (NH 4 OH, 25 wt%) were obtained from Aldrich.
- 2.2. Preparation of Fe-MWNTs
The pristine MWNTs were purified by impregnating them with 5 M HNO 3 for 5 h at room temperature. Purified MWNTs was washed using distilled water until pH 7.0 was obtained. After vacuum filtration, the sample was dried for 24 h at 120℃ in a vacuum oven.
Fe-MWNTs were prepared by suspending 1.0 g of purified MWNTs in 200 mL of distilled water containing 1.0 g FeCl 2 ·4H 2 O and 2.7 g FeCl 3 ·4H6H 2 O at 50℃ under an N 2 atmosphere. Then, 0.5 mL of NH 4 OH solution was slowly added to the above solution under continuous stirring to promote complete growth of the nanoparticle crystals. Subsequently, the composites were centrifugally separated from the solution, washed with distilled water until a pH 7.0 was reached, and dried at 100℃ for 12 h in vacuum. The chemical reaction of the Fe 3 O 4 precipitation is as follows [17] .
Lager Image
- 2.3. Preparation of Fe-MWNTs/PPy
To prepare Fe-MWNT/PPy, the obtained Fe-MWNTs were dispersed in 150 mL of 0.1 M HCl solution. Subsequently, 1 mL of pyrrole was added. After the solution was stirred mechanically for 10 min, it was mixed with an aqueous solution of APS. The polymerization of pyrrole was allowed to proceed for 5 h at approximately 0-5℃ . Then, the final product was washed with copious amounts of water and absolute ethanol and was dried under vacuum at 80℃ for 24 h.
- 2.4. Characterization
The structures of the MWNTs and Fe-MWNTs were characterized using X-ray diffraction (XRD, BRUKER D2 PHASER) with CuKα radiation. The XRD patterns were obtained in 2 θ ranges between 20̊ and 80̊ at a scanning rate of 5̊ /min.
The surface characteristics of the MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy were determined using X-ray photoelectron spectroscopy (XPS, VG Scientific Co., ESCALAB MK- II) with an Al Kα (hν = 1486.6 eV) X-ray source.
For the electrochemical investigation, cyclic voltammetry (CV) and galvanostatic charge-discharge tests were performed using an electrochemical analyzer (Iviumstat, Ivium Technologies) to evaluate the electrochemical performance in the potential range between -0.9 V and 0 V in the 1 M Na 2 SO 3 electrolyte solution.
3. Results and Discussion
Fig. 1 shows XRD patterns of the MWNTs and Fe-MWNTs. Diffraction peaks assigned to the MWNTs at 2θ = 26.5̊ and 43̊ can be clearly seen in the XRD curves of the MWNTs and Fe- MWNTs, indicating that the MWNT structure was not destroyed after the successive deposition of Fe 3 O 4 . The XRD patterns exhibit typical characteristic peaks of Fe 3 O 4 at 2θ = 30.2̊ , 35.4̊ , 46.6̊ , 53.7̊ , 57.3̊ , and 62.8̊ , which is in agreement with the standard values (JCPDS card no. 75-0033). The grain size of the Fe 3 O 4 particles was calculated from the major diffraction peak (311) using the Debye-Scherrer equation [18] .
Lager Image
where L c is the particle size (nm), K is the Scherrer constant (= 0.9), λ is the X-ray wavelength (CuKα = 0.154 nm), θ is the angle at the peak maximum, and β 1/2 is the width (radians) of the peak at half the height. According to equation, the deposited Fe 3 O 4 particles have an average grain size of 14 nm.
The MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy were also characterized using XPS analysis. Fig. 2 shows the wide scan spectrum, in which the photoelectron lines at binding energies of about 285, 533, 400, and 711 eV are attributed to C 1s , O 1s , N 1s , and Fe 2p , respectively. The peaks at 285 eV correspond
Lager Image
X-ray diffraction curves of multi-walled carbon nanotubes (MWNTs) and Fe-MWNTs.
Lager Image
X-ray photoelectron spectroscopy curves of multi-walled carbon nanotubes (MWNTs), Fe-MWNTs, and Fe-MWNTs/PPy.
Lager Image
Cyclic voltammetry curves of multi-walled carbon nanotubes (MWNTs), Fe-MWNTs, and Fe-MWNTs/PPy at the scan rate of 50 mV/s in 1 M Na2SO3 electrolyte.
with the sp 2 hybridized carbon of the MWNTs [19] . The N 1s spectrum of Fe-MWNTs/PPy shows its peak at a binding energy of about 400 eV, which is characteristic of amine-like or neutral pyrrolium nitrogens (-NH- structure) [20] . In the case of Fe 2p , the core-level spectra of the Fe-MWNTs and Fe- MWNTs/PPy show very similar peaks at a binding energy of about 711 eV. It can be suggested that there is no significant chemical reaction between PPy and Fe-MWNTs, and that Fe-MWNTs are used as a template for the polymerization of conducting PPy.
The electrochemical performance of MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy was measured using CV and charge-discharge curves in 1 M Na 2 SO 3 electrolyte solution. Fig. 3 presents the CV curves of each electrode between a potential from -0.9 to 0 V at a scan rate of 50 mV/s. It can be seen that the MWNT electrodes have symmetrical, rectangular-shaped voltammograms, which is a characteristic feature of EDLCs. However, anodic peaks and cathodic peaks were observed in the CV for the Fe-MWNTs and Fe- MWNTs/PPy electrodes, which is attributed to the redox reactions of Fe 3 O 4 . The possible mechanism is as follows [21] :
Lager Image
Charge/discharge curves of multi-walled carbon nanotubes (MWNTs), Fe-MWNTs, and Fe-MWNTs/PPy with 0.2 A/g in 1 M Na2SO3 electrolyte.
Lager Image
Lager Image
The galvanostatic charge-discharge curves of MWNT, Fe- MWNT, and Fe-MWNTs/PPy electrodes were investigated at 0.5 A/g; the corresponding results are shown in Fig. 4 . It can be seen that the curve of the MWNT electrode is very symmetrical, indicating that the MWNT electrode has perfect EDLC behavior. However, the shapes of the charge-discharge behavior of the Fe- MWNT and Fe-MWNTs/PPy electrode did not show the characteristics of a pure electrochemical double-layer capacitor, which is in agreement with the result obtained from CV in Fig. 3 .
The specific capacitance can be measured by the galvanostatic charge-discharge behavior, according to the following equation [22] :
Lager Image
where I is the current of charge-discharge, t the discharge time, ΔV the potential window, and m the mass load of active materials. The calculated specific capacitances of the MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy are 20, 60, and 73 F/g, respectively. It is obvious that the specific capacitance of the Fe- MWNTs/PPy is improved by the coating of PPy, which enhances the electric conductivity, lowers the resistance, and facilitates the charge-transfer of the composites.
4. Conclusions
In this work, Fe-MWNTs/PPy was successfully prepared by the coprecipitation of Fe 3+ and Fe 2+ and the in situ polymerization of pyrrole. From the CV results, the prepared Fe-MWNT and Fe-MWNTs/PPy electrodes showed pseudo-capacitive characteristics in terms of their electrochemical reversibility and reactivity. Charge-discharge measurement of the prepared electrodes at 0.5 A/g yielded specific capacitances of 20, 60, and 73 F/g for MWNTs, Fe-MWNTs, and Fe-MWNTs/PPy, respectively. Among these electrodes, the Fe-MWNTs/PPy electrode exhibited excellent capacitive performance and had a high specific capacitance from -0.9 to 0 V in 1 M Na 2 SO 3 electrolyte due to pseudo-capacitance stemming from the redox reaction of Fe 3 O 4 and the high electric conductivity and increased charge transfer between Fe-MWNTs and PPy.
We acknowledge the financial support by grants from Korea CCS R&D Center, funded by the Ministry of Education, Science and Technology of Korean Government.
Conway BE (1999) Electrochemical Supercapacitors: Scientific Fundamentals and Technological Applications Plenum Press New York
Bao L , Zang J , Li X (2011) Flexible Zn2SnO4/MnO2 core/shell nanocable? carbon microfiber hybrid composites for high-performance supercapacitor electrodes Nano Lett 11 1215 -    DOI : 10.1021/nl104205s
Simon P , Gogotsi Y (2008) Materials for electrochemical capacitors Nat Mater 7 845 -    DOI : 10.1038/nmat2297
Frackowiak E , Beguin F (2001) Carbon materials for the electrochemical storage of energy in capacitors Carbon 39 937 -    DOI : 10.1016/s0008-6223(00)00183-4
Li W , Chen D , Li Z , Shi Y , Wan Y , Wang G , Jiang Z , Zhao D (2007) Nitrogen-containing carbon spheres with very large uniform mesopores: the superior electrode materials for EDLC in organic electrolyte Carbon 45 1757 -    DOI : 10.1016/j.carbon.2007.05.004
Kim KS , Park SJ (2012) Bridge effect of carbon nanotubes on the electrical properties of expanded graphite/poly(ethylene terephthalate) nanocomposites Carbon Lett 13 51 -    DOI : 10.5714/CL.2012.13.1.051
Kim YH , Park SJ (2010) Effect of pre-oxidation of pitch by H2O2on porosity of activated carbons Appl Chem Eng 21 183 -
Kong LB , Lang JW , Liu M , Luo YC , Kang L (2009) Facile approach to prepare loose-packed cobalt hydroxide nano-flakes materials for electrochemical capacitors J Power Sources 194 1194 -    DOI : 10.1016/j.jpowsour.2009.06.016
Seo MK , Saouab A , Park SJ (2010) Effect of annealing temperature on electrochemical characteristics of ruthenium oxide/multi-walled carbon nanotube composites Mater Sci Eng B 167 65 -    DOI : 10.1016/j.mseb.2010.01.028
Wang H , Hao Q , Yang X , Lu L , Wang X (2009) Graphene oxide doped polyaniline for supercapacitors Electrochem Commun 11 1158 -    DOI : 10.1016/j.elecom.2009.03.036
Frackowiak E , Delpeux S , Jurewicz K , Szostak K , Cazorla-Amoros D , Béguin F (2002) Enhanced capacitance of carbon nanotubes through chemical activation Chem Phys Lett 361 35 -    DOI : 10.1016/s0009-2614(02)00684-x
Lee H , Kim H , Cho MS , Choi J , Lee Y (2011) Fabrication of polypyrrole (PPy)/carbon nanotube (CNT) composite electrode on ceramic fabric for supercapacitor applications Fabrication of polypyrrole 56 7460 -    DOI : 10.1016/j.electacta.2011.06.113
Li J , Yang QM , Zhitomirsky I (2008) Nickel foam-based manganese dioxide? carbon nanotube composite electrodes for electrochemical supercapacitors J Power Sources 185 1569 -    DOI : 10.1016/j.jpowsour.2008.07.057
Wei Z , Wan M , Lin T , Dai L (2003) Polyaniline nanotubes doped with sulfonated carbon nanotubes made via a self-assembly process Adv Mater 15 136 -    DOI : 10.1002/adma.200390027
Qu S , Wang J , Kong J , Yang P , Chen G (2007) Magnetic loading of carbon nanotube/nano-Fe3O4 composite for electrochemical sensing. Talanta 71 1096 -    DOI : 10.1016/j.talanta.2006.06.003
Park SK , Park SJ , Kim S (2012) Preparation and capacitance behaviors of cobalt oxide/ graphene composites Carbon Lett 13 130 -    DOI : 10.5714/CL.2012.13.2.130
Tao K , Dou H , Sun K (2008) Interfacial coprecipitation to prepare magnetite nanoparticles: concentration and temperature dependence Colloids Surf Physicochem Eng Aspects 320 115 -    DOI : 10.1016/j.colsurfa.2008.01.051
Zheng Y , Zhang M , Gao P (2007) Preparation and electrochemical properties of multiwalled carbon nanotubes?nickel oxide porous composite for supercapacitors Mater Res Bull 42 1740 -    DOI : 10.1016/j.materresbull.2006.11.022
Li Y , Tang L , Li J (2009) Preparation and electrochemical performance for methanol oxidation of pt/graphene nanocomposites Electrochem Commun 11 846 -    DOI : 10.1016/j.elecom.2009.02.009
Rezaul Karim M , Lee CJ , Sarwaruddin Chowdhury AM , Nahar N , Lee MS (2007) Radiolytic synthesis of conducting polypyrrole/carbon nanotube composites Mater Lett 61 1688 -    DOI : 10.1016/j.matlet.2006.07.100
Wu NL , Wang SY , Han CY , Wu DS , Shiue LR (2003) Electrochemical capacitor of magnetite in aqueous electrolytes J Power Sources 113 173 -    DOI : 10.1016/s0378-7753(02)00482-2
Kim DW , Rhee KY , Park SJ (2012) Synthesis of activated carbon nanotube/ copper oxide composites and their electrochemical performance J Alloys Compd 530 6 -    DOI : 10.1016/j.jallcom.2012.02.157