Advanced
Design Feature-Based Jetfighter Shape Modeling
Design Feature-Based Jetfighter Shape Modeling
International Journal of Aeronautical and Space Sciences. 2013. Sep, 14(3): 222-228
Copyright ©2013, The Korean Society for Aeronautical Space Science
This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/bync/3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : May 03, 2013
  • Accepted : August 13, 2013
  • Published : September 30, 2013
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Jing Zang
School of Aeronautic Science and Engineering, Beihang University, Beijing, China
Hu Liu
School of Aeronautic Science and Engineering, Beihang University, Beijing, China
Tianping Liu
BUAA Research Institute Co., Ltd, Beihang University, Beijing, China
liutp@buaa.edu.cn
Xianping Ni
School of Aeronautic Science and Engineering, Beihang University, Beijing, China

Abstract
A jetfighter shape modeling method based on design features is researched, to improve the efficiency of shape modeling in the stage of conceptual aircraft design. The aircraft’s general design features and shape parameters, including geometric and position parameters, are described. The coordinate systems of the entire aircraft and its components are defined. As a sample of local shape, a method of inlet intake modeling is introduced. The whole process of the modeling method is proposed. Three examples of different jetfighters are listed, to describe the achievement of basic layout, which includes four main elements. The Fusion of Components can be achieved by regulating the details of the sections of the fuselage. Sample Cases of typical layouts are shown to verify the effectiveness of the proposed method, which provides the basis for further analysis and optimization.
Keywords
1. Introduction
The conceptual design is a very important stage in the process of aircraft development [1] . The work in this stage has a decisive impact on the aircraft’s final capability, and the designers need to raise multiple design proposals with high quality, for comparison and selection. In order to make full use of advanced analysis and optimization methods, the aircraft’s shape should be easily and quickly modeled, without hindering the progress of the conceptual design [2] .
Antoine and Kroo developed a framework for aircraft conceptual design and environmental performance studies [3 - 4] . Denney et al. used an improved parametric geometry for propulsion-airframe integration [5] . Nunez et al. presented a novel methodology for enabling the visualization and exploration of data obtained during aircraft multi-objective optimization at the conceptual design stage [6] .
To provide suitable models, the theories and technologies of CAD-based models are researched quite widely. Amadori et al. used CAD-Tools to achieve models in a distributed conceptual design framework [7] . Li and Keane researched robust parametric CAD models in a knowledge-based geometry repair system [8] . However, CAD tools are more suitable for later preliminary and detail, instead of conceptual design [9] .
Besides the CAD-based modeling, some methods of parametric modeling built into the aircraft conceptual design software have been developed, such as RDS from the American Conceptual Research Corporation; ACSYNT from Virginia Polytechnic Institute and State University and the NASA Ames Research Center; and the Synthetic Environment for Aircraft Conceptual Design (SEACD) and Open Conceptual Aircraft Design System (OpenCADS) from Beihang University [9 - 14] . In addition, Rodriguez and Sturdza developed a rapid geometry engine (RAGE), for preliminary design analysis without labor-intensive CAD support [15] . Suwaratana and Rodriguez researched a method for using the RAGE geometry modeler to achieve a more efficient conceptual design process [16] . Hahn developed the Vehicle Sketch Pad (VSP) as a parametric geometry modeler for conceptual aircraft design [17] . Gloudemans and McDonald used VSP to accomplish parametric models for high fidelity analysis [18] . Raymer researched the geometry mathematics of the Design Layout Module of RDS-Professional aircraft design software [19] . However, the traditional parametric modeling software is based on the geometric characteristics of components, and easy to achieve fast and accurate modeling of components, but lacks the ability for grasping the whole shape’s design features.
The research in this paper is completed on the basis of OpenCADS, which includes the modules of design, analysis and optimization. Its built-in examples library of aircraft and dozens of databases of airfoil, engine, and landing gear provide a strong support to complete the design. However, OpenCADS uses a feature-based component modeling method, without parameter definition of the general layout. Therefore, OpenCADS still has the potential to be improved for rapid modeling. This paper will try to focus on the general design features of the jetfighter, not CAGD (Computer Aided Geometric Design), such as the research from Athanasopoulos et al. [20] . The design of the advanced jetfighter embodies state-of-the-art aviation technology, and will be the object to be modeled in this paper. This article describes how to summarize the design features of a typical jetfighter, and achieve rapid shape modeling, based on the features.
PPT Slide
Lager Image
Aircraft’s shape parameters
2. Parametric Description of the General Design Features
The engines, airborne equipment and load of a typical jetfighter are always finished products. In the aircraft design process, the modeling of these products is generally finished separately, so that the components of finished products are not included in the jetfighter’s shape in this paper.
The design features of the aircraft’s whole shape include the shape features of the various components, and the assembly relationships among them. To describe the aircraft shape parameters based on the design features, the geometric and position parameters of the various components should be defined ( Fig. 1 ). The geometric parameters are used to determine the shape of a single component. Moreover, the position parameters are used to determine the component’s assembly relationship with others. In addition, the components of an aircraft can be divided into fuselagelike and wing-like components. Fuselage-like components include the traditional fuselage, canopy and inlet; winglike components include the wing, empennage and others. Compared to the components’ geometry features summary method [11] , design feature-based modeling can better describe the basic shape of the entire aircraft completely, and contribute to a faster forming of the aircraft shape scheme. However, different types of aircraft may have greatly different shapes, so that the method proposed in this paper applies only to jetfighters.
As shown from Fig. 1 , the shape of the fuselage-like component is built with setting its contour line and sections ( Fig. 2 ), and the shape of the wing-like component is built with setting its geometric parameters, such as taper ratio
PPT Slide
Lager Image
Modeling of the fuselage-like component
and sweep angle. Its important to note that only the right side model is built based on the settings, and the use of the left side is generated by the mirror mode. To preserve continuity at the symmetry plane, the user is allowed to set the tangential vector in the section. Moreover, the positioning of the fuselagelike component is completed by setting the coordinates of the component’s origin, and the positioning of wing-like components is completed by setting the position coordinates, including the front root point and assembly angle.
The type of curves used in OpenCADS is the B-Spline curve. The B-Spline is defined as:
PPT Slide
Lager Image
In the equation, Pi means the vertice of the control polygon. Ni,k(t) is the B-Spline basis function.
3. Shape Modeling Method
Firstly, inherited from OpenCADS, the coordinate system should be defined ( Fig. 3 ). There are three sub-coordinate systems in this coordinate system, with different usage. The coordinate system Oxyz is regarded as the coordinate system of modeling, and the management reference point of the model’s actual geometry information. O'x'y'z' is the absolute coordinate system of the fuselage, and the head point of the fuselage is usually set as the origin of the coordinate system. O''x''y''z'' is the coordinate system of fuselage components
PPT Slide
Lager Image
Definition of the coordinate system
used for the modeling of components. The various fuselage components are completely assembled through the coordinate origin’s position of the absolute coordinate system of the fuselage [12] . In this paper, the origin of the fuselage component’s coordinate system is defined on the front surface of the fuselage component, and the origin of the wing component’s coordinate system is defined on the leading edge root point.
The process of design feature-based jetfighter shape modeling can be summed up in three stages, including basic layout modeling, local shape modeling, and fusion of components ( Fig. 4 ). The accomplishing means is to respectively set the geometry and position parameters of the fuselage-like components and wing-like components.
- 3.1 Basic Layout Modeling
In this paper, the basic layout is defined as the four main elements, including layout type, engine type, vertical tail type, and inlet location ( Fig. 5 ).
  • The layout type actually represents the relative relationship between the main wing and horizontal tail. Typical advanced jetfighters take the conventional type and canard type, and rarely take the tailless type.
  • Modern jetfighters are equipped with single or dual engines. The twin-engine jetfighter needs more fuselage space, so that larger sections should be set in fuselage modeling. Moreover, more space should be left for inlets.
PPT Slide
Lager Image
Modeling process
PPT Slide
Lager Image
Elements of basic layout
  • Advanced fighters usually have single or dual vertical tails. The rough shape and location of vertical tails need be determined first in the stage of basic layout modeling, and can be adjusted in the stage of components fusion.
  • Inlet types of different jetfighters have many differences. Both sides and abdomen types of air intakes, or the modifications of these two forms, are common.
Jetfighter shapes are classified through the above four elements. Jetfighters with the identical four elements can be regarded as having the same basic layout.
To completely achieve the basic layout, the rough shapes of five major components, including the forward fuselage, rear fuselage, main wing, vertical tail, and horizontal tail (canard), should be modeled and positioned. The fuselage is divided into two parts at the position near the inlet’s intake, for inlet modeling in the stage of local shape modeling ( Fig. 6 ). The rectangle with solid line depicts the forward fuselage,
PPT Slide
Lager Image
Two parts of the fuselage
PPT Slide
Lager Image
F-35 as conventional type
and the rectangle with dotted line depicts the rear fuselage.
The achievement of the basic layouts are illustrated by the examples of F-35, JAS-39, and LCA, respectively, corresponding to the conventional type, canard type and tailless type ( Figs. 7 - 9 ). Points A, B, C, D, and E in the figures represent coordinate system origins of the forward fuselage, rear fuselage, main wing, vertical tail, and horizontal tail (canard). After the shapes modeling, the basic layout of the jetfighter can be sketched, by setting the position parameters of these major components ( Table 1 ).
The basic layout determines the basic shape of the aircraft ( Fig. 10 ). The local shape modeling and fusion of components should be finished based on the basic layout, too. Moreover, the completed basic layout can be saved as a project, for shape modeling of the same or a similar aircraft design. Therefore, the stage of basic layout modeling is the core of the design feature-based jetfighter shape modeling method.
PPT Slide
Lager Image
JAS-39 as canard type
PPT Slide
Lager Image
LCA as tailless type
The position of major components
PPT Slide
Lager Image
The position of major components
- 3.2 Local Shape Modeling
The stage of local shape modeling is to model the details of the jetfighter, usually including canopy, inlet and nozzle. Although not significant as the basic layout, local details are also important manifestations of the design features.
The following is an example of inlet intake, to illustrate the local shape modeling. In order to sort out the design features of the inlet intake, the elements, including basic type, location type and section shape, are defined ( Fig. 11 ).
  • In this paper, the basic type refers to the conventional type and DSI (Diverterless Supersonic Inlet), which has become quite popular in recent years.
  • As previously described, the location type includes the
PPT Slide
Lager Image
Basic layout of the Mirage-200
PPT Slide
Lager Image
Features of inlet intake
PPT Slide
Lager Image
Sections of different inlet intakes
  • both sides type and abdomen type. The space where the inlet intake is located should be left to the stage of basic layout modeling.
  • The common section types of inlet intake can be divided into semicircular, rectangular, and diamond.
Summarizing the design features, the complex inlet intake is decomposed into simple geometric shapes that will be respectively modeled, by setting the contour lines and sections. It is worth noting that in the inlet intake modeling, the section shape embodies more design features ( Fig. 12 ).
- 3.3 Fusion of Components
Through the first two stages, the basic shape of the entire jetfighter has been formed. Contemporary jetfighters often have a wing-fuselage fusion design with a smooth transition between the components, so a step is needed to modify the details of the junctions. The means of realization is regulating the details of the sections of the fuselage, to accommodate the other components. It is worth noting that the basic layouts of some jetfighters may be similar, but there are great differences between their fuselages and other components. Therefore, the sections of fuselage need a great adjustment, when the shape modeling is based on the existing projects of basic layouts.
PPT Slide
Lager Image
Sections of different mid-fuselages
Figure 13 shows the sections of two mid-fuselages. The left one is traditional, and nearly circular. The right one embodies a stealth design with wing-fuselage fusion, and has a wide bottom, because of the equipped buried bomb
PPT Slide
Lager Image
Example of EF-2000
PPT Slide
Lager Image
Example of F-15
PPT Slide
Lager Image
Example of Mirage-2000
bay. Moreover, the figure obviously shows the deformation on both sides of the section, in order to better join the wing.
The fusion of components may not be decisive to the shape of the aircraft, but it is significant in improving the result of the modeling. In addition, a semi-automatic function is provided, to help the user to adjust the model. At this research stage, the semi-automatic function is achieved by fixing the contact section of the two connected fuselagelike components, and the contact airfoil profile of the two wing-like components.
4. Sample Cases
Figures 14 - 16 show more advanced finished jetfighter models that are completed by the design feature-based jetfighter shape modeling method. To cover the basic layouts of the form of the state-of-the-art fighter, the normal layout, no tail and canard layout, with distinct layout features of the wing-like components and inlets, are included [21 , 22] . From these sample cases, this method’s capability of jetfighter shape modeling can be verified.
5. Conclusion
The shape model of an aircraft is significant in the stage of conceptual design. Through improving OpenCADS, a method of design feature-based jetfighter shape modeling is researched. The general design features of a jetfighter are described. Through three stages, which are basic layout modeling, local shape modeling and fusion of components, the shape of a jetfighter can be achieved. Three sample cases of advanced jetfighters are listed, to verify the capability of the shape modeling method. The jetfighter shape modeling method based on design features can achieve a new design more quickly than the traditional parametric modeling, resulting in speeding the next process of analysis and optimization, to boost the general concept design.
Acknowledgements
The authors wish to thank Mingqiang Luo, who supportedthe development of the software.
References
Gu S., F. 2001 Aircraft conceptual/preliminary design Beijing University of Aeronautics and Astronautics Press Beijing
Raymer D. P. 1999 Aircraft design: a conceptual approach 3rd edition AIAA Inc Reston
Nicolas E. A. , Ilan M. K. 2005 “Framework for Aircraft Conceptual Design and Environmental Performance Studies” AIAA JOURNAL 43 (10) 2100 - 2109    DOI : 10.2514/1.13017
Nicolas A. , Ilan K. , Karen W. , Garrett B. 2004 “A Framework for Aircraft Conceptual Design and Environmental Performance Studies” 10th AIAA/ISSMO Multidisciplinary Analysis and Optimization conference Albany, New York AIAA-2004-4314
Russell K. D. , Jimmy C. T. , Dimitri N. M. 2012 “Parametric Geometry for Propulsion-Airframe Integration” 50th AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition Nashville, Tennessee AIAA-2012-0548
Nunez M. , Maginot J. , Padulo M. , Guenov M. 2009 “Integrated Exploration and Visualization of Optimal Aircraft Conceptual Designs” 50th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference Palm Springs, California
Amadori K. , Johansson B. , Krus P. 2007 “Using CADTools and Aerodynamic Codes in a Distributed Conceptual Design Framework” 45th AIAA Aerospace Sciences Meeting and Exhibit Reno, Nevada AIAA-2007-964
Dong L. , Andras S. , Andy J. K. 2010 “A Knowledge-Based Geometry Repair System for Robust Parametric CAD Models” 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition Orlando, Florida AIAA-2010-1508
Liu H. , Wu Z. , Wang G. L. , Wang X. L. 2004 “Implementation of a Sketch Based Approach to Conceptual Aircraft Design Synthesis and Modeling” Chinese Journal of Aeronautics 17 (4) 207 - 214    DOI : 10.1016/S1000-9361(11)60238-0
Raymer D. P. 1992 “RDS: A PC-Based Aircraft Design, Sizing, and Performance System” AIAA Aircraft Design Systems Meeting Hilton Head, South Carolina AIAA-92-4226
Lu X. L. , Liu H. , Wu Z. 2006 “Components parameterization in helicopter conceptual design” Journal of Beijing University of Aeronautics and Astronautics 32 (1) 46 - 49
Luo M. Q. , Feng H. C. , Liu H. , Wu Z. 2009 “Rapid Cabin Design and Automated Scheme Adjustment for Civil Aircraft” Acta Aeronautica et Astrnautica Sinica 30 (1) 73 - 80
Luo M. Q. , Feng H. C. , Liu H. , Wu Z. 2009 “Rapid wing structure design and automated scheme adjustment for civil aircraft” Journal of Beijing University of Aeronautics and Astronautics 35 (4) 468 - 471
Luo M. Q. , Liu H. , Wu Z. 2008 “Prototype System Research on Open Conceptual Aircraft Design” Acta Aeronautica et Astrnautica Sinica 29 (4) 954 - 959
David L., R. , Peter S. “A Rapid Geometry Engine for Preliminary Aircraft Design” 44th AIAA Aerospace Sciences Meeting and Exhibit Reno, Nevada AIAA-2006-929
Dejapong L. S. , David L. R. 2011 “A More Efficient Conceptual Design Process Using the RAGE Geometry Modeler” 49th AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition Orlando, Florida AIAA-2011-159
Andrew S. H. 2010 “Vehicle Sketch Pad: A Parametric Geometry Modeler for Conceptual Aircraft Design” 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition Orlando, Florida AIAA-2010-657
James R. G. , Robert M. 2010 “Improved Geometry Modeling for High Fidelity Parametric Design” 48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition Orlando, Florida AIAA-2010-659
Daniel P. R. 2011 “Conceptual Design Modeling in the RDS-Professional Aircraft Design Software” 49th AIAA Aerospace Sciences Meeting including the New Horizons Forum and Aerospace Exposition Orlando, Florida AIAA-2011-161
Michael A. , Hassan U. , Gabriela G. C. 2009 “Parametric design of aircraft geometry using partial differential equations” Advances in Engineering Software 40 (7) 479 - 486    DOI : 10.1016/j.advengsoft.2008.08.001
China Aviation Information Center 2001 World Aircraft Manuals Air Press Beijing
Paul J. 2005 Jane’s All The World’s Aircraft.2004-2005 Jane’s Information Group Inc Alexandria