Advanced
Flutter Characteristics of a Morphing Flight Vehicle with Varying Inboard and Outboard Folding Angles
Flutter Characteristics of a Morphing Flight Vehicle with Varying Inboard and Outboard Folding Angles
International Journal of Aeronautical and Space Sciences. 2013. Jun, 14(2): 133-139
Copyright ©2013, The Korean Society for Aeronautical Space Science
This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/bync/3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : February 27, 2013
  • Accepted : April 16, 2013
  • Published : June 30, 2013
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Pratik Shrestha
Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701, Republic of Korea.
Min-Soo Jeong
Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701, Republic of Korea.
In Lee
Department of Aerospace Engineering, Korea Advanced Institute of Science and Technology (KAIST), Daejeon 305-701, Republic of Korea.
inlee@kaist.ac.kr
Jae-Sung Bae
School of Aerospace and Mechanical Engineering, Korea Aerospace University, Goyang 412-791, Republic of Korea.
Kyo-Nam Koo
Department of Aerospace Engineering, University of Ulsan, Ulsan 680-749, Republic of Korea.

Abstract
Morphing aircraft capable of varying their wing form can operate efficiently at various flight conditions. However, radical morphing of the aircraft leads to increased structural complexities, resulting in occurrence of dynamic instabilities such as flutter, which can lead to catastrophic events. Therefore, it is of utmost importance to investigate and understand the changes in flutter characteristics of morphing wings, to ensure uncompromised safety and maximum reliability. In this paper, a study on the flutter characteristics of the folding wing type morphing concept is conducted, to examine the effect of changes in folding angles on the flutter speed and flutter frequency. The subsonic aerodynamic theory Doublet Lattice Method (DLM) and p-k method are used, to perform the flutter analysis in MSC.NASTRAN. The present baseline flutter characteristics correspond well with the results from previous study. Furthermore, enhancement of the flutter characteristics of an aluminum folding wing is proposed, by varying the outboard wing folding angle independently of the inboard wing folding angle. It is clearly found that the flutter characteristics are strongly influenced by changes in the inboard/outboard folding angles, and significant improvement in the flutter characteristics of a folding wing can be achieved, by varying its outboard wing folding angle.
Keywords
1. Introduction
Operating aircraft efficiently can significantly help to reduce their operating costs. However, the efficiency of the aircraft that are widely used today in the aviation industry is limited, due to their design constraints. Therefore, aircraft that are capable of morphing their wing forms are highly desired over conventional aircraft with fixed wings, since they can be operated efficiently at different flight profiles [1] .
In the past, several aircraft have been designed that can change their wing surface plan form, for optimal performance in flying at different flight conditions. For instance, the Grumman F-14 [2] can change its sweep angle from 20° to 67.5° for high speed flight, of up to Mach 2.4. The Rockwell International B-1 [3] can sweep its wings forward, during takeoff, landing and high altitude cruise, and the wings are swept aft, for subsonic and supersonic flight. The XB-70 supersonic bomber [4] can fold its wingtip while travelling at high speed, in order to trap the shockwave under the wings. The folded wing tip could also be used for lateral directional stability, substituting the need for a larger and heavier vertical fin.
Current morphing aircraft concepts being developed involve far more radical changes in their wing shape, so as to perform efficiently at varying flight conditions. The Hyper- Elliptic Cambered Span (HECS) morphing wing concept, being developed by researchers at NASA, can provide 15% better lift to drag ratio, compared to planar and elliptical wings [5] . The NextGen Aeronautics variable sweep and variable root chord concept, also known as the bat wing concept [6] , involves sweeping of the wing from 15° to 45°, for efficient high lift, cruise and dash operation. Furthermore, the stealth operation-capable folding wing concept being developed by Lockheed Martin can vary its span by 100%, and plan form area by 120%, for cruise and loiter missions [7] . Its unfolded configuration allows the aircraft to be used for efficient loitering, whereas folding the wing reduces the wing’s surface area, for flying at high speed.
There are many challenges faced by such radical morphing concepts. Among them, occurrence of dynamic aeroelastic instability, such as the flutter of lifting surfaces, is of serious concern for the development of morphing aircraft. Such instability can result in the disastrous failure of flight vehicle structures, such as the vertical fin flutter incidents that occurred in the F117 stealth fighter, and E-6 Tacamo [8] . Therefore, it is of utmost priority to investigate the flutter characteristics of morphing aircraft, to ensure that the newly developed morphing wings are safe and reliable.
The flutter behavior of Lockheed Martin’s folding concept is the main research interest discussed in this paper. Research done by Zhao and Hui [9] showed that structural and aerodynamic characteristics of a folding wing are largely dependent on its folding angle. As a result, its flutter speed is also characterized by its folding angle. Additionally, unstable mode changes, as the folding angle is increased, and the flutter behavior of the folding wing,
Lager Image
Flutter analysis procedure
are strongly influenced by structural and aerodynamic damping. Mathew et al. [10] found that the folding wing’s folding angle, hinge stiffness and weight are all strongly inter-related to each other. Its bending modes are considerably influenced by the stiffness of the hinge. The bending modes of the folding wing are dominated by the structural stiffness, for higher spring stiffness at higher folding angles.
In this paper, modal/flutter analyses of a folding wing are performed, and these modal/flutter characteristics are validated with results from previous research [9] . Then, to develop folding wings with better flutter characteristics, further investigation is performed, by varying inboard/ outboard folding angles. Through this research, combinations of inboard/outboard folding angles are determined, to avoid the flutter phenomenon, as the wing configuration is changed.
2. Flutter Analysis
- 2.1 Flutter Analysis Overview
In order to investigate the flutter phenomenon of a folding wing, structural and aerodynamic models are created using MSC.PATRAN FlightLoads. The structural model of the folding wing is composed of the geometry, element, load/ boundary conditions (BC), material, and property. The aerodynamic model contains the aerodynamic conditions/ properties for the flutter analysis. The research discussed here deals with subsonic flow; therefore the subsonic surface aerodynamic theory Doublet Lattice Method (DLM) [11] implemented in MSC.NASTRAN is used, for calculating the aerodynamic forces.
Aerodynamic grids points and structural grid points do not coincide with each other. Therefore, spline approximation is used, to obtain aerodynamic forces on structural grid points. Finally, MSC.NASTRAN is used for flutter analysis of the folding wing, using the p-k method [12] . The procedure for performing the flutter analysis is illustrated in Fig. 1 .
- 2.2 Flutter Solution Method: p-k Method
In this p-k method, the solution for the flutter problem is found by solving the eigenvalue problem. Neglecting the structural damping, the flight vehicle’s equation of motion, considering only the external loading from the aerodynamic forces, can be written as
Lager Image
where, [ M ] is the mass matrix, [ K ] is the stiffness matrix, { u } is the displacement, and the function on the right hand side represents the aerodynamic forces.
Aerodynamic forces are given by the summation of motion dependent and motion independent aerodynamic forces, and can be written as
Lager Image
Then by substituting Eq. (2) in Eq. (1), and assuming the unsteady aerodynamic forces depend only on displacements, the equation of motion can be rewritten as
Lager Image
where, ρ is the free stream air density, V is the velocity, and [ Q ] is the aerodynamic force matrix. The generalized aerodynamic matrix [ Q ] is a function of the Mach number and reduced frequency. Since the equation is homogenous, a simple exponential function of time can be used to describe Eq. (3).
By using
Lager Image
and substituting it in Eq. (3), the eigenvalue problem is transformed to
Lager Image
In Eq. (5), by substituting
Lager Image
the p-k flutter solution can be written as
Lager Image
where, b is a reference semi-chord of the lifting surface, and p refers to the complex response frequency and eigenvalue. The complex response frequency and eigenvalue, p can be expressed as
Lager Image
where, k is the reduced frequency, and γ denotes the decay rate coefficient.
One key advantage of using the p-k method for determining the flutter characteristics is that it allows flutter analysis to be carried out, based on any given velocity. Additionally, it provides realistic approximate estimates of system damping at subcritical speeds, and at subcritical damping conditions, damping values closely characterize the physical damping. However, the results acquired using p-k methods can be difficult to interpret, due to frequent mode switching, and in this method, the reduced frequency cannot be equal to 0.
Using the p-k method, the flutter phenomenon can be found, when γ =0. So, once the flutter analysis is completed, V-g and V-f plots are drawn, to find the flutter speed and flutter frequency, when the sign of damping value changes from negative to positive.
3. Folding Wing Flutter Characteristics
- 3.1 Baseline Folding Wing
The structure of the folding wing consists of: fuselage, inboard folding wing and outboard folding wing, as shown in Fig. 2 (a). These three substructures are connected to each other by a hinge element, with a torsional stiffness of 4Nm/rad. The folding configuration of the folding wing is illustrated in Fig. 2 (b). For the baseline folding wing case, the inboard wing segment folds from 0° to 120°, while the outboard wing rotation angle remains at 0°.
Modeling of the isotropic folding wing structure is done in MSC.PATRAN FlightLoads, with respect to the dimension presented in Fig. 2 (a). The fuselage, inboard wing and the outboard wing, with thickness of 2mm, 1mm and 1mm, respectively, are assigned with aluminum material properties. A clamped boundary condition is applied to the fuselage section. Properties of the baseline folding wing are tabulated in Table 1 .
- 3.2 Baseline Folding Wing Flutter Analysis
The modal analysis of the baseline folding wing is performed using MSC.NASTRAN solution sequence SOL 103. Figure 3 shows the changes in natural frequency of the four lowest modes of the folding wing, as the inboard wing folding angle (IWFA) is increased from 0° to 120°.
Significant change in natural frequencies can be observed, due to changes in the wing’s structural geometry. The 3rd mode natural frequency is the most affected, with increase in the IWFA. The present modal results, when compared
Lager Image
Folding wing configuration
with the reference results [9] , show the results to be in good agreement with each other.
Flutter analysis is carried out in MSC.NASTRAN, using solution sequence SOL 145. The flutter speed and flutter frequency of the folding wing are calculated for IWFA from 0° to 120°, and plotted as shown in Fig. 4 .
Varying the IWFA from 0° to 120° results in drastic changes in the flutter speed and frequency of the folding wing, as shown in Figs. 4 (a) and (b) respectively. It is observed that the flutter characteristics of the folding wing structure are dominated by instability of the 2nd mode for an IWFA between 0° to 93°, 4th mode for an IWFA between 94° to 112°, and 3rd mode beyond 112° of the IWFA.
For the region between 0° and 60° of IWFAs, flutter results in torsion of the inboard wing, and coupled bending and
Baseline folding wing properties
Lager Image
Baseline folding wing properties
torsion of the outboard wing, due to second mode instability, as visualized in Fig. 5 (a). Flutter instability of the 2nd mode occurs in this region, due to the merging of the 1st and 2nd modes. In the folding angle against flutter speed plot shown in Fig. 4 (a), flutter speed increases slightly by 31m/s to 33m/s, between IWFAs of 0° to 20°. When the IWFA is increased from 20° to 60°, the folding wing flutter speed decreases by 18%, to about 27m/s. Minor change in flutter frequency can be observed in Fig. 4 (b), i.e. it remains at about 12Hz.
Whereas, the second mode instability dominating the flutter characteristics between 60° and 93° IWFA, is due to the merging of the 2nd and 3rd modes. This results in the torsion of the inboard wing, and the bending of the outboard wing, as shown in Fig. 5 (b). Increase in the IWFA from 60° to 93° results in sharp increase in flutter speed, from 27.4m/s to 49.9m/s, while the flutter frequency drops by about 15% to 9.958Hz.
4th mode instability occurs between IWFAs of 94° and 112°, due to merging of the 3rd mode and 4th mode. In this folding angle region, 4th mode instability results in the bending of
Lager Image
Modal characteristics of the baseline folding wing
the inboard wing, and coupled bending and torsion of the outboard wing, as shown in Fig. 5 (c). The flutter speed and flutter frequency remain relatively constant in this region, at about 50m/s and 26Hz, respectively.
Finally, in the IWFA region beyond 112° 3rd mode instability occurs, due to the merging together of the 2nd and 3rd mode. Merging of the 2nd and 3rd modes results in a mode shape of the folding wing similar to that for the case between an IWFA of 60° and 93° i.e. the torsion of the inboard wing, and the bending of the outboard wing. The mode shape for this case is visualized in Fig. 5 (d). Beyond 112° IWFA, change in dominant instability mode from the 4th mode to
Lager Image
Baseline folding wing flutter characteristics
Lager Image
Folding wing mode shape visualizations
3rd mode causes both the flutter speed and flutter frequency to drop, from 50.1m/s to about 20.3m/s, and from 26.441Hz to 13.916Hz, respectively.
The present flutter results of the baseline folding wing are compared with the reference results [9] , and the results are found to be in close agreement. From the present result, it can be concluded that the purpose of using a folding wing for high speed operation can be constrained, due to the flutter phenomenon. Therefore, in the following sections, the flutter speed of the folding wing is investigated, by varying both the inboard and outboard wing, to improve its flutter characteristics.
4. Flutter Analysis of a Folding Wing with Varying Inboard/Outboard Wing
In order to enhance the flutter characteristics of the folding wing, further analyses are done, by varying its outboard wing folding angle (OWFA), independent of the IWFA. Table 2 shows four cases of OWFA, for which flutter analyses are performed. A hinge stiffness of 4Nm/rad, similar to the baseline folding wing, is used for the flutter analysis.
Figure 6 shows the flutter speed for the IWFAs from 0° to 120°, and for the OWFAs from -30° to 30°, compared with the baseline flutter characteristics. Varying the OWFA causes the IWFA, at which the unstable mode dominating the flutter characteristics shifts from one mode to another, to change. As a result, folding the outboard wing causes the flutter characteristics of the folding wing to drastically differ, from the flutter characteristics of the baseline folding wing. For instance, compared to the baseline flutter characteristics, decreasing the OWFA below 0° causes the flutter instability mode to change at a lower IWFA; and increasing the OWFA above 0° causes the flutter instability mode to change at a higher IWFA. As a result, it can be observed that, as the
Outboard wing folding angle case
Lager Image
Outboard wing folding angle case
Combination of inboard and outboard folding angles for optimal flutter speed
Lager Image
Combination of inboard and outboard folding angles for optimal flutter speed
OWFA is decreased from 0° to -30°, the baseline flutter characteristics shift leftwards on the graph; and as the OWFA is increased from 0° to 30°, the baseline flutter characteristics shift rightwards.
This phenomenon makes it possible to select the best possible combination of IWFA and OWFA for operating the folding wing at maximum possible speed, as the inboard wing is folded from 0° to 120°. This allows the folding wing to be operated safely within a pre-determined region, with respect to the inboard/outboard folding angle combinations.
Inboard/outboard folding angle arrangements that deliver the best flutter behavior of the folding wing are listed in Table 3 . Figure 7 shows the optimal flutter speed attainable through the morphing of inboard/outboard wings, compared with the baseline folding wing flutter characteristics. From Fig. 7 , it can be observed that about 40% increase in flutter speed can be achieved at 50° IWFA, while flutter speed of about 50m/s can be maintained for the IWFA region between 60° to 120°. From the results presented in this section, seen that the flutter speed can be improved as the IWFA is changed, through variation in the OWFA. This characteristic can be especially beneficial, in
Lager Image
Inboard wing folding angle vs. flutter speed for various outboard folding angles
Lager Image
Comparison between baseline flutter speed and optimal flutter speed
allowing the folding wing to fold its wing, in order to fly at higher speed.
5. Conclusion
In this paper, improvement of the flutter characteristics of a folding wing is proposed, through variation of the OWFA, independent of the inboard wing segment. Firstly, baseline isotropic folding wing flutter analysis is carried out, using the p-k method in MSC.NASTRAN. The flutter results obtained through the present method corresponded well with the reference results. From the baseline flutter results of the isotropic folding wing, it can be concluded that folding of the inboard wing segment leads to drastic changes in the flutter characteristics of the folding wing; and its flutter behavior is strongly influenced by the 2nd, 3rd, and 4th mode instabilities. At higher IWFA, the folding wing’s flutter speed decreases, and therefore the purpose of high speed flight with folded wing is greatly hindered by such flutter phenomenon. Therefore, varying the inboard/outboard folding wings, to improve the flutter characteristics of the folding wing, is discussed in this paper.
By varying the OWFA, along with the inboard wing segment, it is found that the baseline folding wing’s flutter characteristics shift either to the left, when the OWFA is decreased, or to the right, when the OWFA is increased. Utilizing this shift in flutter characteristics, combinations of the inboard/outboard wing folding angles, as shown in Table 12, can be determined, for optimal flutter speed of the folding wing, which can provide better flutter performance, as the folding wing is morphed.
From the results presented in this paper, it can concluded that the flutter of folding wings can be avoided, for: (i) missions involving loitering, where an unfolded configuration is used for low speed flight, and (ii) high speed cruise missions, by varying both the inboard and outboard wings’ folding angles. This enables the folding wing concept to be used as efficiently, and as safely, as possible.
Acknowledgements
This research was supported by the Agency for Defense Development (ADD-11-01-08), and by the KARI (Korea Aerospace Research Institute), through the KARI-University Partnership Program. The authors are grateful for their support.
View Fulltext  
Canfield B. , Westfall J. 2008 “Distributed actuation system for a flexible in-plane Morphing wing, Advanced Course on Morphing Aircraft, Mechanisms and Systems” Lisbon, Portugal
Baugher J. 2000 Grumman F-14A Tomcat: Joe Baugher's Encyclopedia of American Military Aircraft
Withington T. 2006 B-1B Lancer Units in Combat (Osprey Combat Aircraft 60) Osprey Publishing London
Pace S. 1988 “Triplesonic Twosome” Wings 18 (1)
Lazos B. S. 2005 “Biologically inspired Fixed-Wing Configuration Studies” Journal of Aircraft 42 (5)
Wlezien R. W. , Horner G. C. , McGowan A. R. , Padula S. L. , Scott M. A. , Silcox R. J. , Simpson J. O. 1998 “The Aircraft Morphing Program” 39th AIAA/ASME/ASCE/ASC Structures, Structural Dynamics, and Materials Conference Long Beach, CA
Terrence A. W. 2006 “Morphing Aircraft Technology –New Shapes for Aircraft Design” Purdue University
Michael W. K. 1995 “A Historical Overview of Flight Flutter Testing” NASA Technical Memorandum 4720
Zhao Y. , Hu H. 2012 “Parameterized aeroelastic modeling and flutter analysis for a folding wing” Journal of Sound and Vibration    DOI : 10.1016/j.jsv.2011.08.028
Matthew P. S. , Brian S. , Franklin E. E. , Geoffrey J. F. 2008 “Vibration and flutter characteristics of a folding wing”, Morphing Aircraft Structures: Research in ARFL/RB
Albano E. , Rodden W. P. 1969 “A doublet lattice method for calculating lift distribution on oscillating wings in subsonic flows” AIAA Journal 7 (2) 279 - 285
Hodges D. H. , Pierce G. A. 2002 Introduction to Structural Dynamics and Aeroelasticity Cambridge University Press New York