Low Speed Thrust Characteristics of a Modified Sonic Arc Airfoil Rotor through Spin Test Measurement

International Journal of Aeronautical and Space Sciences.
2012.
Sep,
13(3):
317-322

This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/bync/ 3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

- Received : July 30, 2012
- Accepted : September 26, 2012
- Published : September 30, 2012

Download

PDF

e-PUB

PubReader

PPT

Export by style

Share

Article

Metrics

Cited by

TagCloud

The low speed aerodynamic characteristics for a modified sonic arc airfoil which is designed by using the nose shape function of sonic arc, the shape function of NACA four-digit wing sections, and Maple are experimentally investigated. The small rotor blades of a modified sonic arc and NACA0012 airfoil are precisely fabricated with a commercially available light aluminum(Al 6061-T6) and are spin tested over a low speed range (3000rpm-5000rpm). In a consuming power comparison, the consuming powers of NACA0012 are higher than that of modified sonic arcs at each pitch angle. The measured rotor thrust for each pitch angle is used to estimate the rotor thrust coefficient according to momentum theory in the hover state. The value of thrust coefficients for both two airfoils at each pitch angle show almost constant values over the low Mach number range. However, the rotor thrust coefficient of NACA0012 is higher than that of the modified sonic arc at each pitch angle. In conclusion, the aerodynamic performance of NACA0012 is better than that of modified sonic arcs in the low speed regime. This test model will provide a convenient platform for improving the aerodynamic performance of small scale airfoils and for performing design optimization studies.
_{∞}
< 0.8. It is then compared and analyzed with the aerodynamic performance of the NACA0012 airfoil. Harris
[5]
also develops the SC(1, 2)-0174 airfoils which is the modified supercritical airfoil. It is a 14% thick airfoil designed for a lift coefficient of 0.7. This airfoil is tested not only at transonic speeds but also at low speeds in the Langley wind tunnel. In particular, the effects of varying Mach number from 0.10 to 0.32 at a Reynolds number of 6.0 x 10
^{6}
are included in the wind-tunnel test results
[5]
. McGhee et al.
[6]
developed new NASA lowand mid- speed airfoils from the initial low-speed family airfoils. The thickness ratio of the initial airfoils designed for a sectional lift coefficient of 0.4 is changed from 9% to 21%. The new NASA airfoils are developed to increase the cruise Mach number of low-speed airfoils while retaining good high-lift and low speed characteristics. For example, the new NASA airfoils are designed for
C_{l}
=0.3 at
M
_{∞}
=0.15.
Rusak et al.
[7]
investigate the improvement of the aerodynamic efficiency of small-scale airfoils by using a temperature differential between the upper and lower surface and the heat transfer effect with numerical simulations, asymptotic analysis, and experimental work. In the experimental work, the microrotor blades with 6-in (15.24-cm) diameters are spin tested at several blade pitch angle settings ranging from 9 to 15 deg. The microrotor blades are fabricated by using a commercial thermoelectric alloy material that exhibits the Peltier effect which occurs when any two members of the thermoelectric series are connected to form a junction. The application of a control voltage across the thickness of the airfoil results in a temperature differential between the upper and lower airfoil surfaces. This temperature differential influences the rotor aerodynamic performance, and this is measured and compared with the computational results.
As stated above, the supercritical airfoil to enhance the aerodynamic performance of civil airplane wings flying in a transonic regime is developed and its aerodynamic characteristics are tested for both transonic speed and low speed. The results are compared with aerodynamic characteristics of NACA0012 airfoil.
In the present study, the experimental investigations of the aerodynamic characteristics for modified sonic arc airfoils in low speed regimes are conducted as the continuing work of references
[8
,
9]
which are numerical studies for this airfoil in both transonic flow and low speed flow. This airfoil is designed by using the nose shape function of sonic arcs proposed by Rusak
[10]
, the shape function of NACA fourdigit wing sections, and the commercial program Maple.
Here
є
is the thickness ratio of airfoil,
c
is the airfoil chord, and
is the surface function of modified sonic arc airfoil. The surface function
can be obtained as follows.
Using the TSD theory, Schwendenman et al.
[11]
show that the asymptotic shape of sonic arc
is given by the parametric representation:
where -∞ <
v
^{*}
< +∞ and Г(z) is the Gamma function. The arc becomes sonic at a Mach number determined by the relation:
This is the highest critical Mach number which can be achieved for any airfoil with a given thickness ratio at zero angle of attack. Equation (1)-(3) describe a sonic arc at a zero angle of attack. The flow around the sonic arc was studied in detail by Rusak
[10]
. He suggests that the arc shape at the nose of the asymptotic shape (as
x
→ 0 or as
v
^{*}
→ +∞) changes like;
The
nose shape is exactly the nose of the sonic slender semi-infinite body. This special nose shape results in minimal pressure drag contribution among all the power law shapes
with 2/5≤
n
≤1. The nose shape of equation (4) may contribute to the design of improved airfoils with a higher critical Mach number or with reduced drag.
The thickness distribution for NACA four-digit wing sections
[12]
is given by the formula;
Now, we can construct the modified sonic arc airfoil with a nose shape of the body given by equation (4) and a tail angle of NACA four-digit wing sections. Experience with computations shows that the maximum thickness of this airfoil should be located at
=0.415 for the highest critical free stream Mach number. The modified airfoil shape
is given by the formula;
where
c
=1,
h
_{2}
=0.8469,
a
_{1}
=-0.2645,
a
_{2}
=1.3018,
a
_{3}
=-3.6896 and
a
_{4}
=1.8054. The sonic arc and the modified shape with
є
=0.12 are shown in
Fig.1
.
Geometry of Modified Sonic Arc Airfoil є=0.12, Sonic Arc Airfoilє=0.12, and NACA0012 Airfoil
Rotor Blades with Pitch Angle
Experimental Apparatus
50cm distance). The rotor blades are tested from 3000rpm to 5000rpm in room temperature (293.15K) in a low-humidity environment. The platform is rectangular (no taper or sweep), the aspect ratio is 4.5 [9cm radius and 2cm chord], camber is 0%, and the blades are untwisted. The test data for the hovering rotor is collected by the commercial program LabView. The rotor blades are tested at several blade pitch settings ranging from 3 to 12 degree. In order to obtain accurate data, the load cell is fitted on the zero adjustment first. Motor speed is increased by a control lever and we keep the rotor rotating up to the steady state at a fixed rpm. Then ten data per second are collected for ninety seconds by Labview. The mean value of the collected data is calculated and this mean value is regarded as the thrust at a given rpm.
The measured consuming powers for NACA0012 and modified sonic arc airfoils at a given pitch angle are shown in
Fig.4
~
Fig.6
. The curve fitting lines analogized by the least-square regression method are added in all the figures. The consuming powers are increasing as rotor blade speeds are increased in all the figures. Moreover, the consuming powers of NACA0012 are higher than that of the modified sonic arc at each pitch angle. As the pitch angle is increased, the consuming power for both two airfoils is also increased. For example, at a 3 deg. pitch angle, the estimated values of consuming power are 0.52[watt] for NACA0012 and
Measured consuming power vs Rotor speeds with a 3 deg.pitch angle
Measured consuming power vs Rotor speeds with a 6 deg.pitch angle
Measured consuming power vs Rotor speeds with a 12 deg.pitch angle
0.13[watt] for the modified sonic arc at about 4500[rpm]. At a 6 deg. pitch angle, it is 0.62[watt] for NACA0012 and 0.35[watt] for the modified sonic arc at about 4500[rpm]. At a 12 deg. pitch angle, it is 1.45[watt] for NACA0012 and 1.30[watt] for the modified sonic arc at about 4500[rpm].
The experimental data of thrust for each pitch angle are listed in
Table 1
~
Table 3
. These measured rotor thrusts for each pitch angle are used to estimate the rotor thrust coefficients according to momentum theory in the hover state
[13]
. The rotor thrust coefficient is defined on the basis of the rotor disk area A and the tip speed
V_{tip}
=Ω
R
by
C_{T}
=
T
(1/2
ρA
(Ω
R
)
^{2}
) which is the equation (2.31) in reference
[13]
. Here
T
is the rotor thrust, Ω is angular velocity, and
A
=Ω
R
^{2}
(9cm radius).
Fig.7
~
Fig.9
shows the rotor thrust coefficient. The corresponding Mach number range for the rotor blade speeds (3000rpm-5000rpm) is between 0.082 and 0.137. In
Fig.7
, the average of the rotor thrust coefficient is 0.000192 for NACA0012 and 0.000128 for the modified sonic arc. The average thrust coefficient of NACA0012 is 50 % higher than that for the modified sonic arc at a 3 deg. pitch angle. In
Fig.8
, it is 0.000485 for NACA0012 and 0.000398 for the modified sonic arc. The average thrust coefficient of NACA0012 is 22% higher than that for the modified sonic arc at a 6 deg. pitch angle. In
Fig.9
, it is 0.00126 for NACA0012 and 0.00103 for the modified sonic arc. The average thrust coefficient of NACA0012 is 22% higher than that for the modified sonic arc at a 12 deg. pitch angle. In all the figures, the rotor thrust coefficient of NACA0012 is higher than the
Thrust[gf] Measurement for a 3 deg. pitch angle
Thrust[gf] Measurement for a 6 deg. pitch angle
Thrust[gf] Measurement for a 12 deg. pitch angle
Rotor thrust coefficient vs Mach number with a 3 deg. pitchangle
Rotor thrust coefficient vs Mach number with a 6 deg. pitchangle
Rotor thrust coefficient vs Mach number with a 12 deg. pitchangle
rotor thrust coefficient of the modified sonic arc at a given pitch angle. When the pitch angle is doubled, the rotor thrust coefficient of NACA0012 is increased by two and a half times and that of the modified sonic arc is increased by two and a half or three times. Therefore, the aerodynamic performance of NACA0012 is better than that of the modified sonic arc in the low speed regime (3000rpm-5000rpm).

1. Introduction

During the last half century, much research investigating new airfoil design or modification of existing airfoils have been conducted. Especially, transonic small disturbance (TSD) theory may be applied in the aerodynamic design of wings of civil transport airplane and military fighters and in the design of helicopter blades, compressors, and turbines. Many algorithms for Euler solutions or Navier-Stokes equations for transonic flows demonstrate the difficulties in understanding the aerodynamic characteristics of the flows and its complex nonlinear nature as the geometry, the angle of attack, and the speed are changed
[1]
. However, theoretical approaches to transonic flow which can clarify its nature will provide a useful tool for aerodynamic analysis and the design of airfoils and wings in such conditions
[2]
.
To improve the aerodynamic performance of civil airplane and fighter wings in transonic flows, Whitcomb et al.
[3]
suggest the supercritical airfoil which consists of a flat upper surface and cambered lower surface in the trailing edge. Such a flat upper surface creates a shock wave delay in which shock waves may appear beyond the critical Mach number. This delay results in the reduction of drag around airfoils. Also the cambered lower surface in a trailing edge compensates for lift loss around the wings due to a flat upper surface. Spaid et al.
[4]
modify the supercritical airfoil of Whitcomb a little and measure the surface pressure and drag around the modified airfoil over the range of the far field Mach number, 0.6 < M
2. Airfoil Design

The special modified airfoil with a higher critical free stream Mach number and with lower pressure drag at transonic speeds can be constructed by using TSD theory. We call it a “modified sonic arc airfoil”. This airfoil is characterized by arcs which are close to the sonic arc along the forward part of the airfoil up to the maximum thickness point and which connect to a sharp tail. It has a nose shape given by equation (4) and a tail angle of NACA four-digit airfoil family (a sharp tail is used for practical aerodynamic reasons to minimize the boundary layer separation near the trail edge). This newly-designed airfoil is described by the formula
Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

3. Experimental Study

To investigate the aerodynamic performance of the modified sonic arc airfoil, the small rotor blades of the modified sonic arc and NACA0012 airfoil are spin tested like in reference
[7]
. First, the rotor blades of the modified sonic arc and NACA0012 airfoil are designed with CATIA which is a commercial drawing program, and then the rotor blades are accurately fabricated with a commercially available light aluminum(Al 6061-T6) using the 5-axis high speed manufacturing machine called CAM (computeraided manufacturing) machine.
Fig. 2
shows the rotor blades with pitch angles where the diameter of the rotor blade is 18cm and the diameter of the hub is 2.2cm. The experimental apparatus consists of a highly sensitive load cell for measuring rotor thrust, a laser light source coupled to a frequency counter to measure rotor speed, and a corelessdc motor with associated fixtures which connect the rotor blades to the motor output spindle.
Fig. 3
shows the test apparatuses mounted on two columns (50cm height and
Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Thrust[gf] Measurement for a 3 deg. pitch angle

Lager Image

Thrust[gf] Measurement for a 6 deg. pitch angle

Lager Image

Thrust[gf] Measurement for a 12 deg. pitch angle

Lager Image

Lager Image

Lager Image

Lager Image

4. Conclusion

The low speed aerodynamic characteristics of the modified sonic arc airfoil which is designed by using the nose shape function of the sonic arc, the shape function of NACA four-digit wing sections, and the Maple are experimentally investigated. The small rotor blades of the modified sonic arc and NACA0012 airfoil are precisely fabricated with a commercially available light aluminum(Al 6061-T6) using a 5-axis high speed manufacturing machine and then they are spin tested over the low speed range (3000rpm-5000rpm). In the consuming power comparison, the consuming powers of NACA0012 is higher than that of the modified sonic arc at the given pitch angle. The measured rotor thrust is used to estimate the rotor thrust coefficient. The value of the rotor thrust coefficient at each pitch angle shows to be almost consistently over the low Mach number range. For example, the average thrust coefficient for NACA0012 is 0.000198 and that for the modified sonic arc is 0.000128 at a 3 deg. pitch angle. In conclusion, the aerodynamic performance of NACA0012 is better than that of the modified sonic arc in the low speed regime. This test model will provide a convenient platform for improving the aerodynamic performance of small scale airfoils and for performing design optimization studies.
Acknowledgements

This work was supported by a grant from 2011 ResearchFund of ACE(Advancement of College Education).

Nixon D.
1988
Unsteady Transonic Aerodynamics, Progressin Astronautics and Aeronautics
AIAA
Washington DC, USA

Cole J. D.
,
Cook L. P.
1986
Transonic Aerodynamics
North-Holland
New York, USA

Whitcomb R. T.
,
Clark L. R.
1965
“An Airfoil Shape forEfficient Flight at Supercritical Mach Numbers”
NASA TMX-1109

Spaid F. W.
,
Dahlin J. A.
,
Roos F. W.
,
Stivers L. S.
1983
“An Experimental Study of Transonic Flow about a Supercritical Airfoil. Static Pressure and Drag data Obtainedfrom Tests of a Supercritical Airfoil and an NACA0012 Airfoilat Transonic Speeds, Supplement”
NASA-TM-81336- SUPPL

Harris D. C.
,
McGhee R. J.
,
Allison D. O.
1980
“Low-Speed Aerodynamic Characteristics of a 14-percent-ThickNASA Phase 2 Supercritical Airfoil Designed for a LiftCoefficient of 0.7”
NASA TM 81912

McGhee R. T.
,
Beasley W.D.
,
Whitcomb R. T.
1979
“NASA Low- and Medium-Speed Airfoil Development”
NASA Technical Memorandum 78709

Kim J.M.
,
Rusak Z.
,
Koratkar N.
2003
“Small-ScaleAirfoil Aerodynamic Efficiency Improvement by SurfaceTemperature and Heat Transfer”
AIAA Journal
41
(11)
2105 -
2113

Lee J.C.
2007
“Aerodynamic performance of ModifiedSonic Arc Airfoil”
Journal of Korean Society for Aeronautical and Space Sciences
35
(7)
581 -
585

Lee J.C.
2012
“Low Speed Aerodynamic Characteristicof Modified Sonic Arc Airfoil”
Journal of Korean Society for Aeronautical and Space Sciences
40
(2)
139 -
145

Rusak Z.
1995
“Transonic Flow around Optimum CriticalAirfoils”
SIAM Journal of Applied Mathematics
55
(5)
1455 -
1467

Schwendenman D. W.
,
Kropinski M.C.A.
,
Cole J.D.
1993
“On the Construction and Calculation of OptimalNonlifiting Critical Airfoils”
ZAMP Journal of Applied Mathematics and Physics
44
556 -
571

Abbott I.H.
,
von Doenhoff A.E.
1959
Theory of WingSections
ver Publications Inc.
New York

Leishman J.G.
2000
Principles of Helicopter Aerodynamics
Cambridge Univ. Press
Cambridge, UK

Citing 'Low Speed Thrust Characteristics of a Modified Sonic Arc Airfoil Rotor through Spin Test Measurement
'

@article{ HGJHC0_2012_v13n3_317}
,title={Low Speed Thrust Characteristics of a Modified Sonic Arc Airfoil Rotor through Spin Test Measurement}
,volume={3}
, url={http://dx.doi.org/10.5139/IJASS.2012.13.3.317}, DOI={10.5139/IJASS.2012.13.3.317}
, number= {3}
, journal={International Journal of Aeronautical and Space Sciences}
, publisher={The Korean Society for Aeronautical & Space Sciences}
, author={Lee, Jang-Chang}
, year={2012}
, month={Sep}