Advanced
Performance Enhancement of Organic Light-emitting Diodes with an Electron-transport Layer of Bathocuproine
Performance Enhancement of Organic Light-emitting Diodes with an Electron-transport Layer of Bathocuproine
Transactions on Electrical and Electronic Materials. 2016. Feb, 17(1): 37-40
Copyright © 2016, The Korean Institute of Electrical and Electronic Material Engineers
This is an open-access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0) which permits unrestricted noncommercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : December 12, 2015
  • Accepted : January 01, 2016
  • Published : February 25, 2016
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Jin-Woong Honga
ealab@kw.ac.kr
Yi-Wei Guo
Jong-Yeol Shin
ealab@kw.ac.kr
Tae Wan Kim
Abstract
Performance enhancement of organic light-emitting diodes (OLEDs) is investigated in a device structure of ITO/TPD/Alq 3 /LiF/Al and ITO/TPD/Alq 3 /BCP/LiF/Al. Here, bathocuproine (BCP) is used as an electron-transport layer. Current density-voltage-luminance characteristics of the OLEDs show that the performance of the device is better with BCP layer than without BCP layer. The current density, luminance, luminous efficiency, and external-quantum efficiency are improved by approximately 22%, 50%, 2%, and 18%, respectively. Since the BCP layer lowers the electron energy barrier, electron transport is facilitated and the movement of hole is blocked as the applied voltage increases. This results in an increased recombination rate of holes and electrons.
Keywords
1. INTRODUCTION
The development of science in the 20 th century has contributed greatly to human civilization, especially, in the evolution of displays and the internet. In addition, the 21 st century has come with great capacity and the information age based on high-speed information processing technologies. The basis of information processing technology is the various developments of large and small displays according to the contributions of computers and telecommunication. Recently, light-emitting diode (LED) has been applied to a display. The LED is classified as inorganic and organic LED. For the inorganic LED, the driving voltage of the device is 100 [V] or more, and it is difficult to fabricate large displays because the device is produced by vacuum deposition [1] . In particular, a blue LED is difficult and expensive. However, the OLED has a great advantage for display because it can overcome the disadvantage of inorganic LED [2 , 3] . Thus, the OLED is a promising device in the future, because it can easily produce various colors depending on the choice of synthesized materials. Conventional displays such as CRT, PDP, and TFT-LCD are expected to be replaced by the flexible OLED [4] .
In 1963, Pope et al., studied LED made with organic material composed of anthracene mono-crystalline [5 , 6] . The device using the anthracene was composed of a thick crystal and required a high driving voltage of around 100 [V]. The power conversion efficiency of the device using the anthracene was ≤ 0.1%, and the external-quantum efficiency was at least 5%. In 1987, Tang and VanSlyke reported green OLED operated at a low voltage by using a low molecule [7 , 8] ; and subsequently in 1990, Friend in Cambridge University reported green OLED using the polymer PPV. Since then, tremendous research has been carried out to obtain the OLED with high efficiency and robust durability [9 , 10] . Several studies were conducted in order to understand conduction mechanism and dynamic behavior of charge carriers. The necessity of research on the equivalent circuit analysis led to studies, such as that of Roy, who analyzed the equivalent circuit including the organic layer to a resistive component and a capacitive component [11 , 12] . Pospisil reported that complex impedance is affected from the resistive to the capacitive contribution depending on the frequency and the applied voltage [13] . In 2013, Narayan et al., studied an effect of hole injection and hole blocking layer on the performance of OLEDs with the use of CuPc and bathocuproine (BCP), respectively [14] . In this paper, we present the influence and effect on the electrical properties of the OLEDs with an insertion of electron-transport layer of BCP.
2. EXPERIMENTAL
- 2.1 Specimen
Indium-Tin-Oxide (ITO) substrate was used as an anode, which has a surface resistance of approximately 8 [Ω/sq].
Figure 1 shows the patterned shape of the ITO electrode. The size of the glass is 20 [mm] × 20 [mm] and that of the patterned ITO line is 5 [mm] × 20 [mm].
PPT Slide
Lager Image
Patterned shape of the ITO electrode.
Figure 2 shows the process involved in making the ITO anode. At first, insulating tape is attached on top of the ITO glass with a width of 5 [mm]. The place that is not taped on the ITO glass, was etched by exposing it to the stream of aqua regia mixed with hydrochloric acid (HCI) and nitric acid (HNO 3 ) with a volume ratio of 3:1 for 40 [min]. Ultrasonic wash was conducted in acetone for 25 [min], subsequently, in the solution mixed with ammonia and hydrogen peroxide and deionized water of volume ratio 1:1:5 at 80℃ for 60 [min]; and again, in acetone at 50℃ for 20 [min]; and finally in isopropyl alcohol at 50℃ for 20 [min]. After the ultrasonic cleaning, deionized water was applied for 20 [min] and it was completely dried.
PPT Slide
Lager Image
Etching and cleaning process of the ITO substrate.
- 2.2 Experiment
Figure 3 shows a device structure of the OLED in our experiment; ITO(170 nm)/TPD(40 nm)/Alq 3 (60 nm)/BCP(0 or 5 nm)/LiF(1 nm)/Al. ITO and Al are used as the anode and cathode, respectively. The BCP layer is made to 0 or 5 nm thickness. For the deposition method, all the organics are deposited using thermal vapor deposition at a pressure of 5 × 10 −6 [Torr]. Deposition rates of TPD, Alq 3 , and (BCP and LiF) are 1.0 [Å/s], 1.5 [Å/s], and 0.2 ~ 0.3 [Å/s], respectively. Al of 99.99% purity purchased from Aldrich Co. is evaporated using a tungsten boat. The active area of the device is made to a size of 3 × 5 [mm 2 ] by using a shadow mask.
PPT Slide
Lager Image
Device structure of the OLED used in our experiment.
Figure 4 shows the energy-level diagrams of the OLEDs (a) with and (b) without the BCP layer. The values of HOMO (Highest Occupied Molecular Orbital) and LUMO (Lowest Unoccupied Molecular Orbital) for the hole-transporting TPD material are 5.4 [eV] and 2.2 [eV], respectively; those for the emissive Alq 3 material are 5.8 [eV] and 3.1 [eV], respectively; those for the electron-transport BCP material are 6.4 [eV] and 2.9 [eV], respectively; and LUMO of the electron-injecting LiF material is 3.0 [eV].
PPT Slide
Lager Image
Energy-level diagrams of the (a) ITO/TPD/Alq3/LiF/Al and (b) ITO/TPD/Alq3/BCP/LiF/Al.
The value of LUMO is decreased by approximately 0.6 [eV[ with insertion of the electron-transport BCP layer. The injection of the electron is facilitated due to decreases in the value of HOMO by approximately 0.6 [eV],. The device performance is improved by the increases in recombination rate of the electron and the hole due to blocking of the hole transport [15] . Four organic materials are used in our device fabrication.
Table 1 shows the name and the molecular structure of the organic materials used. In this experiment, the current density-voltage-luminance characteristics of OLEDs are measured with the Keithley 6517 electrometer and Keithley 2000 multimeter, and a Programmable Vupower Co. as the DC Power supply. Lab-view program is used to control the voltage and the current, and the silicon photodetector is placed at the front of the device to measure the photocurrent. The DC current is measured with the Keithley 2000 multimeters depending on the applied voltage.
Name and molecular structure of the organic materials.
PPT Slide
Lager Image
Name and molecular structure of the organic materials.
Figure 5 shows the schematic of the current density-voltage-luminance measuring system.The photocurrent is proportional to the number of photons generated by the illumination of light to the photodector, and the DC current flowing through the device is proportional to the number of electrons. Therefore, the light-emitting efficiency and the external-quantum efficiency of the device are obtained through the photocurrent and the DC current. All the experiments are conducted at room temperature; the applied voltage to the device is increased by 0.25 [V/s]; and the measuring delay time is 1,000 [ms].
PPT Slide
Lager Image
Schematic of measuring current density-voltage-luminance characteristics.
3. EXPERIMENTAL RESULTS AND DISCUSSION
Figures 6 shows the current density-voltage characteristics for the devices with/without the electron- transport BCP layer. Even though the figure shows a similar nonlinear characteristic, there is a difference in current density below 10 [V] for the devices with/without the BCP layer. However, when the applied voltage is above 10 [V], the current density in the device with the BCP layer is slightly higher than that without BCP layer.
PPT Slide
Lager Image
Current density-voltage characteristics.
Figure 7 shows the corresponding luminance-voltage characteristics of the devices. The luminance characteristics become distinct above 6 [V]. Use of BCP layer to the device results in improvements of maximum current density and maximum luminance by approximately 22[%] and 50[%], respectively. The maximum current density is 305.6 [mA/cm 2 ] and 373.4 [mA/cm 2 ], and the maximum luminance is 4,004 [cd/m 2 ] and 5,989[cd/m 2 ] for the devices with/without the BCP layer, respectively. It is thought that the luminance is improved due to the increased recombination of holes and electrons in a device with the BCP layer by lowering the electron energy barrier. Thus, the BCP layer facilitates the movement of electrons and blocks the movement of holes.
PPT Slide
Lager Image
Luminance-voltage characteristics.
Figure 8 shows the luminous efficiency depending on the applied voltage for the devices with/without the electron-transport BCP layer. The maximum luminous efficiency of the device without BCP layer at a voltage of 7.75 [V] is about 6.05 [lm/W], and that of the device with BCP layer at a voltage of 8.75 [V] is approximately 6.17 [lm/W].
PPT Slide
Lager Image
Luminous efficiency (η)-voltage characteristics.
Figure 9 shows the external-quantum efficiency (η ext )-voltage characteristics for the devices with/without BCP layer. The maximum external-quantum efficiency for the device without BCP layer is approximately 0.546% at 7.75 V, and that for the device with BCP layer is approximately 0.644% at 9 V. Thus, the maximum luminous efficiency and the maximum external-quantum efficiency are improved by 2% and 18%, respectively, with the insertion of electron-transport BCP layer. These are summarized in Table 2 .
PPT Slide
Lager Image
External-quantum efficiency (ηext)-voltage Characteristics.
Maximum values of luminance and efficiencies for the devices with/without BCP layer.
PPT Slide
Lager Image
Maximum values of luminance and efficiencies for the devices with/without BCP layer.
4. CONCLUSIONS
Electrical and optical characteristics of the OLEDs were studied in a device structure of ITO/TPD/Alq 3 /LiF/Al ITO/TPD/Alq 3 /BCP/LiF/Al in order to investigate the effect of electron-transport BCP layer. Since the BCP layer lowers the electron energy barrier, the electron transport is facilitated and the movement of hole is blocked as the applied voltage increases. This results in an increased recombination rate of holes and electrons. The study results indicate that the current density, luminance, luminous efficiency, and external-quantum efficiency are improved by approximately 22%, 50%, 2%, and 18%, respectively. Thus, it is expected that the electron-transport BCP material could contribute to the next generation of flat-panel display industry.
Acknowledgements
“The work reported in this paper was conducted during the sabbatical year of Kwangwoon University in 2015”.
References
Ohmori Y. , Fujii A. , Uchida M. , Yoshino K. (1993) Appl. Phys. Lett. 62 3250 -
Hosokawa C. , Higashi H. , Kusumoto T. (1993) Appl. Phys. Lett. 62 3238 -
Zhang Z. L. , Jiang X. Y , X. H. Xu , Nagatomo T. , Omoto O. (1997) Synth. Met. 91 131 -
Vincett P. S. , Barlow W. A. , Hann R. A. , Roberts G. G. (1982) Thin Solid Films 94 171 -
Pope M. , Kallmann H. , Magnante P. (1963) J. Chem. Phys. 38 2042 -
Helfrich W. , Schneider W. G. (1965) Phys. Rev. Lett. 140 229 -
Tang C. W. , VanSlyke S. A. (1987) Appl. Phys. Lett. 51 913 -
Tang C. W. , Vanslyke S. A. (1989) J. Appl. Phys. 65 3610 -
Burroughes J. H. , Bradley D. C. , Brown A. R. , Marks R. N. , Mackay K. , Friend R. H. , Burn P. I. , Holmes A. B. (1990) Nature 347 539 -
Dodabalapur A. (1997) Solid State Communications 102 259 -
Roy S. , Kunndu S. , Roy S. K. , Pal A. J. 2002 Materials Chemistry and Physics 77 784 -
Lee Y. H. , Kim W. J. , Cho K. S. , Lee J. Y. , Kim T. W. , Hong J. W. (2008) Jour. of the Korean Physical Society 53 1460 -
Pospisil J. , Honskus J. , Fahnrich J. , Hlidek P. , Toman P. (1997) Journal of Luminescence 72 522 -
Narayan K. , Varadharajaperumal S. , Mohan Rao G. , Varma M. Manoj , Srinivas T. (2013) Curr. Appl. Phys. 13 18 -
Isii H. 2012 Device Physics, Material Chemistry, and Device Application of Organic Light Emittting Diodes Popular Ed. CMC Publishing 13 -