Design and Analysis of a Vibration-driven AA Size Electromagnetic Energy Harvester Using Magnetic Spring

Transactions on Electrical and Electronic Materials.
2012.
Jun,
13(3):
125-128

This is an open-access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0) which permits unrestricted noncommercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

- Received : February 20, 2012
- Accepted : May 29, 2012
- Published : June 25, 2012

Download

PDF

e-PUB

PubReader

PPT

Export by style

Share

Article

Metrics

Cited by

TagCloud

This paper describes the design, simulation and characterization of an AA size electromagnetic energy harvester that is capable of converting environmental vibration into electrical energy. A magnetic spring technique is used to scavenge energy from low frequency external vibrations. The generator is characterized by ANSYS 2D finite element analysis, and optimized in terms of moving mass, fixed magnet size, coil width and load resistance. The optimized energy harvester is able to generate 53.5 mW of average power at 8.1 Hz resonance frequency, with a displacement of 0.5 mm.
^{2}
).
In this paper, we present the design and analysis of an AA size electromagnetic energy harvester that uses a magnetic spring. A
Schematic diagram of the magnetic spring transducer.
magnetic spring type generator has the advantages of low resonance frequency, simple construction process and easy vibration under off-resonance conditions
[11]
. The output of the transducer is maximized by optimizing the fixed magnet size, coil width, coil position, and load resistance. Moreover, nonlinear behavior of the harvester is reduced, by increasing the height of the moving magnet compared with the coil width.
F
is applied to the system. By applying Newton’s second law to the moving magnet, we can write:
where,
m
is the moving magnet mass,
x
is the relative displacement between moving magnet and generator housing, and
P
is the gravitational force.
The force between top and moving magnet can be expressed as
[12]
:
where,
r
is the distance between two poles,
Q=H_{c}.A, H_{c}
is the coercive force, and
A
is the pole surface area.
Similarly, the force between bottom and moving magnet is:
Flux density distribution for three positions of the moving magnet at (a) 10 mm, (b) 20 mm, and (c) 30 mm from the top magnet.
So, the spring constant (
k
), can be written in the following form:
Equation (1) can be written as:
where,
D_{p}
and
D_{e}
are the parasitic damping coefficient and electromagnetic damping coefficient, respectively.
Therefore, the solution of the displacement of (6) can be formulated as:
The average generated power at resonance (i.e. ω=ω
_{n}
=√(k/m)) can be written as:
ANSYS 2D finite element analysis was used to evaluate the nonlinear behavior of the flux density across the coil surface. For convenience and ease of fabrication, an air gap of 1 mm was chosen between the moving magnet and the inner surface of the cylinder.
The average flux density across the coil surface was calculated by dividing the surface into 15 paths and taking the average for
Simulation parameters.
Flux density across the coil surface with respect to the position of the moving magnet.
moving magnet positions in the space between the top and bottom fixed magnets.
Figures 3
(a)-(c) show the patterns of magnetic flux density for three positions of moving magnets at 10 mm, 20 mm and 30 mm from the top magnet, respectively. The simulation parameters are shown in
Table 1
.
The next section discusses the optimization of output by maximizing the moving mass, fixed magnet sizes, coil width, coil position and load resistance in detail.
^{2}
moving magnet size at 8.8 Hz resonance frequency.
Similarly, for the optimization of the fixed magnet at the top and bottom ends of the tube, a trade-off is required between the
Open circuit voltage vs. resonance frequency for different moving magnet size.
Open circuit voltage and frequency vs. top (A) and bottom (B) magnet size.
Open circuit voltage vs. coil width at resonance frequency.
flux density and mass displacement. As shown in
Fig. 5
, when a 1x1 mm2 size magnet is used at the top and bottom, the device operates at a lowest resonance frequency (7.8 Hz). However, at this time, the output voltage is low (9.67 V). An optimum voltage of 11.4 V is obtained when a 1×1 mm
^{2}
and 2×2 mm
^{2}
size magnet is used at the top and bottom, respectively.
Figure 6
shows the open circuit voltage for different coil widths. As observed, a smaller coil width (5 mm) gives a higher output voltage (12.96 V), indicating that there is less possibility of flux enclosing than that with a larger coil width. Flux lines that are totally enclosed by the coil do not have any contribution to the resultant output voltage, because the total flux linkage for
Open circuit voltage vs. coil center position from the middle point of the cylinder.
Optimized parameters of proposed harvester.
those flux lines with the coil is constant [15].
For our model, the resting point of the moving magnet is slightly lower than the middle position, due to gravitational force. Under the excitation, the speed of the moving magnet is high around the resting point, and gradually decreases towards the end of the tube, due to the opposite poles of the fixed magnets at the top and bottom.
Fig. 7
shows the variation of output voltage at different coil centre positions from the middle point of the tube. As can be seen, the output reaches its maximum value of 13.88 V when the position is 2 mm below the middle point, since the speed of the moving magnet is maximum around this position.
The output power was calculated by Matlab simulation, using a variable resistor (0-500 Ω). A maximum average power of 53.5 mW was obtained at 97 Ω load resistance, as shown in
Fig. 8
. The optimized parameters of the proposed AA size electromagnetic energy harvester are given in
Table 2
.
Measured power vs. load resistance at resonance condition.

1. INTRODUCTION

Wireless sensors have recently become very popular, due to their portability and wide range of applications in remote and physically inaccessible locations. These sensors require a compact, low cost, long operating life and light-weight energy source
[1]
. Usually, fixed energy alternatives, such as batteries and fuel cells are used as a power source for those sensors. However, batteries have the limitation of short operational life. Therefore, it is impractical to use batteries as an energy source for applications that require sensors to be installed for long duration or in physically inaccessible locations, such as biomedical implants and structure embedded micro sensors
[2]
. Moreover, recent advances in battery energy density are lagging compared with advances in micro-system technology
[3]
. As a result, the battery size is often more bulky than the system itself. Energy harvesting from ambient energy sources is a possible alternative to batteries, converting energy from an existing source within their environment into usable electrical energy. Therefore, a fully self-sustaining system can be implemented by using energy harvesting techniques; and this will also reduce the problems of interconnection, electronic noise and control complexity. There are several environmental energy sources such as thermal, solar, tidal and wave energy, acoustic noise, wind and vibration
[4]
. Vibration is more attractive, since it is inherent in nature
[5
,
6]
.
In this work, we designed an AA size electromagnetic energy harvester. Pioneering work on AA size transducers has been carried out by research groups
[7
,
8]
, who proposed two AA size energy harvesters using a spring mass system, which is capable of producing a maximum 120 μW and 830 μW power at 70.5 Hz and 100 Hz resonance frequency, respectively. Korla et al.
[9]
described a generator of the same size using a piezoelectric transduction technique, which was able to generate a power of 625 μW at 50 Hz resonance frequency. However, resonance frequency of the stated harvesters is very high. On the other hand, ambient vibration frequencies are very low (1-10 Hz)
[6]
. Efforts have also been conducted to reduce the operating frequency of harvesters; e.g. using a frequency up-conversion technique, it is possible to operate the transducer at 25 Hz resonance frequency
[4]
. However, it can generate only 3.79 μW maximum power. Tzeno et al.
[10]
developed a bi-stable mechanical structure to scavenge energy from a low frequency environment. They showed that their device could harvest a peak power of 288 μW at 10 Hz resonance frequency, but the system input acceleration is very high (9.8 m/ s
Lager Image

2. DESIGN

- 2.1 Generator structure

Figure 1
is a schematic diagram of a magnetic spring generator. A moving magnet is inserted into a hollow plastic straw. Then, two opposite poles fixed magnets have been placed vertically, in such a way that each pair of facing surfaces of magnets has the same pole. A coil of enamel coated copper wire is wrapped horizontally around the outer casing of the plastic straw. When an external force is applied to the structure, the middle magnet starts to oscillate, due to magnetic repulsion of the two fixed magnets and hence AC voltage will be induced in the coil.
- 2.2 Modeling and simulation

The proposed energy harvester can be described by a spring mass system. Assume that a sinusoidal force
Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Lager Image

Simulation parameters.

Lager Image

Lager Image

3. RESULTS AND DISCUSSION

When the axial movement of the magnet is less than the coil width, the response (i.e. flux density vs. distance) shows some nonlinearity towards the ends
[11]
. The nonlinearity can be reduced by increasing the axial movement of the magnet, since increase of the moving magnet mass reduces the linear stiffness coefficient. As observed from
Fig. 3
, the response shows more linearity with the increase of size of the moving magnet.
During optimization, we find out the output voltage for different sizes of moving magnet by keeping all other parameters (e.g. fixed magnet sizes, coil width and coil position) constant. As the size of the moving magnet increases, flux density across the coil also increases, however, displacement speed of the moving magnet decreases
[13
,
14]
. Hence, a trade-off is required between the flux density and the moving magnet’s displacement speed, to optimize the output voltage. As depicted in
Fig. 4
, a maximum voltage of 10.4 V is obtained for a 6×14 mm
Lager Image

Lager Image

Lager Image

Lager Image

Optimized parameters of proposed harvester.

Lager Image

4. CONCLUSIONS

In this paper, an AA size electromagnetic energy harvester has been presented, which can harvest energy from low frequency environmental vibrations. The output voltage of the transducer was maximized by optimizing the moving magnet size, fixed magnet sizes, and coil width. Moreover, nonlinear behavior of the generator was reduced, by increasing the height of the moving magnet relative to the coil width. The optimized harvester generated a maximum average power of 53.5 mW with an input displacement of 0.5 mm at 8.1 Hz frequency. The main advantages of the proposed magnetic spring type energy harvester are simple operation, low cost and long operating life. Furthermore, the generator is able to operate at 8.1 Hz resonance frequency. Therefore, the proposed generator would be very useful for supplying power in health care and environmental monitoring sensor system applications.
Lager Image

Acknowledgements

This work was supported by the Next Generation Military Battery Research Center Program of the Defense Acquisition Program Administration and the Agency for Defense Development, and a Korea Research Foundation Grant through Basic Research 2011 of the Korean Government, which was conducted by the Ministry of Education, Science and Technology (No. 2011- 0013831).

Roundy S.
,
Wright P. K.
,
Rabaey J.
(2003)
Compt. Commun
26
1131 -

Seah W. K. G.
,
Eu Z. A.
,
Tan H.P.
(2009)
Proc. of CTIF Wireless Conf., VITAE

Starner T.
(2002)
IEEE Computer
35
133 -
** DOI : 10.1109/ICSENS.2004.1426407**

Külah H.
,
Najafi K.
(2008)
IEEE Sens. J
8
261 -
** DOI : 10.1109/JSEN.2008.917125**

Sari I.
,
Balkan T.
,
Kulah H.
(2008)
Sens. Actuators A
145
405 -
** DOI : 10.1016/j.sna.2007.11.021**

Kulah H.
,
Najafi K.
(2004)
Proc. 17th IEEE Conf. on MEMS
237
** DOI : 10.1109/MEMS.2004.1290566**

Yuen S. C. L
,
Lee J. M. H.
,
Li W. J.
,
Leong P. H. W.
(2007)
IEEE Pervasive Comput
6
64 -

Lee J. M. H.
,
Yuen S.C.
,
Li W. J.
,
Leong P. H. W.
(2004)
Proc. Int. Symp. Circuits Syst
4
876 -
** DOI : 10.1109/ISCAS.2003.1206360**

Korla S.
,
Leon R.A.
,
Tansel I.N.
,
Yenilmez A.
,
Yapici A.
,
Demetgul M.
(2011)
J. Micromech. Microeng
42
265 -
** DOI : 10.1016/j.mejo.2010.10.018**

Galchev T.
,
Kim H.
,
Najafi K.
(2009)
Prof. of Eurosensors XIII Conf
1439 -
** DOI : 10.1016/j.proche.2009.07.359**

Mann B.P.
,
Sims N.D.
(2009)
J. Sound Vib
319
515 -
** DOI : 10.1016/j.jsv.2008.06.011**

Mukhopadhyay I. S.C.
,
Donaldson J.
,
Sengupta G.
,
Yamada S.
,
Chakraborty C.
,
Kacprzak D.
(2003)
IEEE Trans. Magn
39
3220 -
** DOI : 10.1109/TMAG.2003.816727**

Mizuno M.
,
Chetwynd D.G.
(2003)
J. Micromech. Microeng
13
209 -

Awaja N.
,
Sood D.
,
Vinay T.
(2009)
Sens. Trans. J
103
109 -

Duffy M.
,
Carroll D.
(2004)
IEEE 35th Ann. Power Electronics Specialists Conf
2075 -

Citing 'Design and Analysis of a Vibration-driven AA Size Electromagnetic Energy Harvester Using Magnetic Spring
'

@article{ E1TEAO_2012_v13n3_125}
,title={Design and Analysis of a Vibration-driven AA Size Electromagnetic Energy Harvester Using Magnetic Spring}
,volume={3}
, url={http://dx.doi.org/10.4313/TEEM.2012.13.3.125}, DOI={10.4313/TEEM.2012.13.3.125}
, number= {3}
, journal={Transactions on Electrical and Electronic Materials}
, publisher={The Korean Institute of Electrical and Electronic Material Engineers}
, author={Foisal, Abu Riduan Md
and
Chung, Gwiy-Sang}
, year={2012}
, month={Jun}