Effects of Partial Substitution of W for Ti in Titanium Dioxide
Effects of Partial Substitution of W for Ti in Titanium Dioxide
Transactions on Electrical and Electronic Materials. 2011. Apr, 12(2): 68-71
Copyright ©2011, The Korean Institute of Electrical and Electronic Material Engineers
  • Received : January 28, 2011
  • Accepted : March 21, 2011
  • Published : April 25, 2011
Export by style
Cited by
About the Authors
Eun-Seok, Lee

Ti 1-x W x O 2-y solid solutions with compositions of x = 0.01(TW-1), x = 0.02(TW-2), x = 0.03(TW-3) and x = 0.04(TW-4) were prepared at 1,073 K in air under atmospheric pressure. All the solutions exhibited tetragonal symmetries. Nonstoichiometric chemical formulas have been obtained from oxidation-reduction titration and the partial substitution of W 6+ ions mainly caused the formation of Ti 3+ ion, rather than oxygen excess. Resistivities of the samples were highly dependent on humidity. The increase of the W amount resulted in an increase of Ti 3+ content, decrease of resistivity values and finally degradation of photocatalytic activities.
Titanium dioxide (TiO 2 ) has been widely investigated for as a photocatalyst due to its electronic and optical properties, nontoxicity, long-term stability, and low cost [1] . The phases of TiO 2 are anatase, rutile, and brookite. Their functional characteristics highly depend on their phases. TiO 2 is well known to have photocatalytic activity under ultraviolet (UV) light (band gap of 3.0-3.3 eV). However, it is desirable to develop a photocatalyst that efficiently absorbs visible light [2] , which occupies the main part of the solar spectrum.
Various attempts, such as sol-gel method [3] , thin film method [4] , microwave hydrothermal method [5] , have been made to develop those catalysts. Dopings of various transition metal ions or rare earth ions in TiO 2 have been intensively investigated for photocatalytic decomposition of organic compounds. It has been recently announced that the visible light active photocatalysts of TiO 2 can be obtained from substitution of Ti by transition metals, such as Cr, Ni or Fe [6 - 8] , or even by doping with nonmetal atoms [9 - 13] , such as nitrogen. Few of these studies investigated the mixed valence state [14] of Ti and its effects on the electrical [15] and photocatalytic properties. Thus, in this paper, those properties of each sample, such as crystal symmetry,unit cell volume change, mixed valence states of Ti, variations of oxygen amounts with temperature change, electrical resistivities,and photocatalytic degradation profiles, were examined after synthesizing the anatase type solid solutions (x = 0.01, 0.02, 0.03 and 0.04) of Ti 1-x W x O 2-y in air at 1,073 K (800℃).
Four different samples of the Ti 1-x W x O 2-y system with the compositions of x = 0.01(TW-1), x = 0.02(TW-2), x = 0.03(TW-3) and x = 0.04(TW-4) were synthesized from analytical reagents,TiO 2 (anatase, 99.9%) and WO 3 (99.99%) using standard ceramic techniques in air, after stoichiometric calculation. The starting materials were dried at 673 K for 2 hours to eliminate the water content before weighing. All materials were mixed and ground into fine powders for 2 hours using automatic mortar equipment (03-083-03, Samhwa, Seoul, Korea) to synthesize homogeneous solid solutions [16] . Then, they were stirred and dispersed in polyethylene beakers containing distilled water (200 mL), ethyl alcohol (10 mL), and ceramic beads (Cenobeads, CZC-1.2 mm,Cenotec Co., Changwon, Korea) for 72 hours to get the powders as fine as possible. Each mixture was reacted at 1,073 K in air for 24 hours and then slowly cooled with reactor after leaching and drying. The weighing, grinding, and heating processes were repeated three times under the same conditions to obtain homogeneous solid solutions. The pellets and the residual powder samples with respective compositions were sintered at 1,073 K in
Lager Image
X-ray diffractogram patterns of Ti1-xWxO2-y (x = 0.01 0.02 0.03 and 0.04) system prepared at 1073 K in air and slowly cooled with reactor.
air for 24 hours and cooled with the furnace, after pressing each powder sample into pellets with 10 mm diameter and 1~2 mm thickness under a pressure of 800 kg/cm2.
Each powder sample was analyzed by X-ray powder diffraction (PW1710 [Philips, Almelo, Netherlands], 2θ range: 20°~70°) to assure the homogeneous phase of the solid solution and to determine the related parameters. The observed d values were compared to the theoretical d values calculated from the leastsquare method [17] . Crystal systems, lattice parameters, and lattice volumes of the unit cells were determined, after miller indices of each line were reasonably confirmed (JCPDS data, #21-1272).
The mixed valences of titanium and oxygen nonstoichiometries of calcined powder specimens (Ti 3+ (1-x) tTi 4+ (1-x)(1-t) W 6+ xO 2-y (y = -x+(1-x)t/2), x = 0.01(TW-1), 0.02(TW-2), 0.03(TW-3) and 0.04(TW-4)) at room temperature were determined by oxidationreduction titration (Ti 3+ → Ti 4+ + e - ) using 0.01N-KMnO 4 solution in micro-burette. The mole ratio (t values) of Ti 3+ ion to total Ti ion (t value) was calculated using the following formula.
Lager Image
where, N: normality of KMnO 4 solution, ΔV: volume difference between blank test and sample test, M: formula weight of each sample excluding x × t/2 from oxygen 2-y value, and m: sample weight). The results allowed determinations of the nonstoichiometric formulas of the specimens combined with electroneutrality and mass balance conditions.
The electrical resistivities of the pellet-type samples were measured using 236 SMU instrument (Keithley Co., Cleveland, OH,USA). Maintaining constant current, voltages were measured at room temperature (24℃) under atmospheric air pressure
X-ray powder diffraction data of the Ti1-xWxO2-ysystem.
Lager Image
X-ray powder diffraction data of the Ti1-xWxO2-y system.
(relative humidity ≥60%). A special 4-probe apparatus (probe distance: 1.6 mm) fabricated with quartz and platinum wire was used in this resistivity measurement. Four sharp platinum wires were contacted on the shallow holes on the pellet surface. Two springs made of platinum wire were also used to prevent the contacts from working loose. Resistivity data were processed applying Valde's method [16 , 18] .
TG/DTA experiments were conducted by referring to some studies [16 , 19] on perovskites. The instrument model was TG/DTA 220 (Seiko Instruments Inc., Chiba, Japan) and reference material Pt wire (15.520 mg) in the TG/DTA study. The study temperature was raised at 40℃/min in the range of 50-400℃ in this TG/DTA. The weight change data were converted into percentage values for reasonable comparison.
Absorbance spectra were recorded for the samples anatasetype TiO 2 (TiO 2 -A), TW-1 and TW-2 with UV-vis spectrophotometer (Scinco S-3100, LabPlo plus) with a water-jacketed 8-position multi-cell holder for their absorbance in the range of 200-600 nm. Each 4 mL of the emulsion was taken, excluding precipitated solid materials, after vigorous shaking of solutions with each 1 g sample in 40 mL water, leaving them for 4 hours.
Methylene blue (MB) was chosen as the probe material to test the activity [2 , 20] of the five catalysts (TiO 2 -A, TW-1, TW-2, TW-3, and TW-4). The experiment was carried out simultaneously for the catalysts in a quartz-glass reactor (4 mL) in sunlight for 120 minutes, between 12:00 noon and 02:00 pm. The MB aqueous solution (10 -4 M) with each emulsified catalyst in a quartz-glass cylinder was exposed to sunlight during the experiment. Absorbance was recorded every 30 minutes at 665 nm wavelength against appropriate blanks.
The prepared specimens of each composition can be written as follows; TW-1: Ti 3+ 0.99t Ti 4+ 0.99(1-t) W 6+ 0.01 O 2-y (x = 0.01), TW-2:Ti 3+ 0.98t Ti 4+ 0.98(1-t) W 6+ 0.02 O 2-y (x = 0.02), TW-3: Ti 3+ 0.97t Ti 4+ 0.97(1-t) W 6+ 0.03 O 2-y (x = 0.03), and TW-4: Ti 3+ 0.96t Ti 4+ 0.96(1-t) W 6+ 0.04 O 2-y (x = 0.04). Colors of the synthesized specimens gradually changed from white to very weak yellow, denoting some absorption in the visible region [2] .
Figure 1 shows the X-ray diffractograms (XRD) with compositional changes from x = 0.01 to 0.04, which approximated to the tetragonal structure. Not all the XRD patterns exhibited peak splitting or broadening beyond the instrumental resolution. The indexations of the synthesized samples were performed by referring to the JCPDS data (21-1272, space group: I4 1 ) of TiO 2 -anatase system.
Other patterns of TiO 2 , such as rutile (JCPDS: 21-1276), were not observed. It was concluded that the materials with compositional range x = 0.01-0.04 were monophasic compounds with tetragonal symmetry. Table 1 presents related parameters.
When x = 0.1 and 0.2 (not presented in this paper) unreacted
Lager Image
Variations of Ti3+ ratio and resistivity.
Amounts of Ti3+Ti4+and O2-determined by oxidation-reduction titration of the Ti3+(1-x)tTi4+(1-x)(1-t)W6+xO2-y(y = -x + (1 - x)t/2) system.CR: cooled with reactor.
Lager Image
Amounts of Ti3+ Ti4+ and O2- determined by oxidation-reduction titration of the Ti3+(1-x)tTi4+(1-x)(1-t)W6+xO2-y (y = -x + (1 - x)t/2) system. CR: cooled with reactor.
tungsten oxide peaks appeared, depending on their composition.It was expected little difference would exist in lattice volume,when we consider the similar ionic radius of Ti 4+ (0.745 nm)and W 6+ (0.740 nm). The results of the oxidation-reduction titration performed later showed that the amounts of Ti 3+ (0.810 nm)and O 2- ions did not vary markedly. As shown in Table 1 , the unit cell volumes did not distinctly change.
It was possible to measure the amounts of Ti 3+ and Ti 4+ ions in each sample and finally to determine the nonstoichiometric chemical formulas, applying the oxidation-reduction titration method using 0.01N-KMnO 4 solution and assuming that W ion would maintain its oxidation state of 6+ . Table 2 lists the nonstoichiometric data of the products from the chemical analysis,where y refers to oxygen deficiency.
It was expected that the partial substitution of W would cause both the formation of Ti 3+ and excessive oxygen (negative y value),considering the electroneutrality condition.
Lager Image
where, Ti and TiTi' denote Ti ion sites and Ti 3+ at Ti ion site, respectively.It turned out that the partial substitution of the higher valenced W ions resulted mainly in the formation of Ti 3+ ion, not in oxygen excess, in this system. That is, increasing the amount of W ion, the ratio of Ti 3+ (Ti 3+ /Ti(%)) increases steadily, but 2-y retains almost the same values.
A relationship exists between Ti 3+ /Ti(%) ratio and resistivity ( Fig. 2 ); increasing the amount of W, the resistivity values decrease. This kind of tendency was also observed later in the catalytic activity experiment using methylene blue. The resistivity data were obtained from each pellet-type specimen (dia. = 10 mm, probe distance: 1.6 mm) at room temperature (297 K) with relative humidity ≥60%. These values were highly sensitive to hu
Lager Image
Variations of oxygen content (weight %) in air vs. temperature for each sample.
Lager Image
Absorbance spectra of the catalysts TiO2-A TW-1 TW-2 and TW-3.
midity. That is, supply of heat from an electrical dryer instantly made the resistivities of all the pellet samples infinite; they needed considerable time to regain their resistivity values. These results posit that all the emulsified powder samples in water will have considerable conductivities and that will affect the photocatalytic activity of this W-doped TiO 2 system.
Thermogravimetry (TG) experiments were performed with increasing temperature from 323 K (50℃) to 673 K (400℃) to check the changes of oxygen content with temperature change. The conversions of TG raw data into weight percentages ( Fig. 3 ) and in the nonstoichiometric expressions (2-y values) based on the data from the oxidation-reduction titration method ( Table 2 ), assuming that the weight changes were caused only by oxygen content with temperature change. TW-1 and TW-2 exhibited gradual decrease of weight with increasing temperature; 2-y values of TW-1 changed from 1.989 (99.91%, 323 K) to 1.962 (98.55%,673 K) and the amount of Ti 3+ was nearly zero over the entire temperature range.
TW-2 showed a similar tendency (2-y = 1.999 [100%, 323 K] and 1.974 [98.82%, 673 K]) to TW-1. TW-3 and TW-4 showed a slight increase in weight. 2-y values of TW-3 changed from 2.014 (100.47%, 323 K) to 2.024 (100.93%, 673 K). Mole ratios of Ti 3+ (0.11) and Ti 4+ (0.86) at 400℃ could be calculated from these values. Nonstoichiometric values of TW-4 are as follows; 2-y = 2.031(100.84%, 323 K) to 2.051 (101.84%, 673 K), Ti 3+ (0.18, 673 K) and Ti 4+ (0.78, 673 K).
UV-vis absorption spectra of the catalysts, TiO 2 -A, TW-1, TW-2,and TW-3 are shown in Fig. 4 .
While TiO 2 -A has the strongest absorption below 400 nm, the
Lager Image
Photocatalytic degradation profiles of the catalysts TiO2-A TW-1 TW-2 TW-3 and TW-4.
absorbances of TW-1 and TW-2 are much smaller than those of TiO 2 -A. The sample TW-3 and TW-4 (not shown in Fig. 4 ) exhibited almost zero absorbance in the entire wavelength range. However, it can be seen from Fig. 4 that TW-1 and TW-2 have significant absorbance above 400 nm in the visible region compared to undoped TiO 2 -A. Figure 5 shows the MB degradation with five different catalysts. It is noticeable that the photocatalytic activity of W-doped TiO 2 is considerably reduced with composition change. TW-2, TW-3, and TW-4 have almost no photocatalytic activities.
In this study, the control of particle size was difficult, because all the samples were prepared by traditional solid reaction (not by sol-gel method). It is worthwhile to point out here that even though only a small portion of prepared samples can be emulsified in water, possible uses as a photocatalyst may exist. This study concluded that the increase in the amount of W causes an increase of the portion of Ti 3+ , decrease of resistivities (increases of conductivities) and ultimately degradations of photocatalytic activities.
Ti 1-x W x O 2-y solid solutions with compositions of x = 0.01(TW-1, Ti 3+ 0.04 Ti 4+ 0.95 W 6+ 0.01 O 1.99 ), x = 0.02(TW-2, Ti 3+ 0.04 Ti 4+ 0.94 W 6+ 0.02 O 2.00 ), x = 0.03(TW-3, Ti 3+ 0.05 Ti 4+ 0.92 W 6+ 0.03 O 2.01 ) and x = 0.04(TW-4, Ti 3+ 0.05 Ti 4+ 0.91 W 6+ 0.04 O 2.01 ) were synthesized at 1073K in air under atmospheric pressure. XRD study showed that all the solutions had tetragonal symmetries and the unit cell volumes did not distinctly change. The resistivity values decreased with the increase of x value (amount of W). TG analysis showed that while, with increasing temperature, TW-1 and TW-2 exhibited a gradual decrease in weight, TW-3 and TW-4 showed a slight increase in weight. While TiO 2 -A had the strongest absorption below 400 nm, the absorbances of TW-1 and TW-2 were much smaller than those of TiO 2 -A. The photocatalytic activities of W-doped TiO 2 varied considerably with composition. TW-2, TW-3, and TW-4 had almost no photocatalytic activity.
Luo H , Takata T , Lee Y , Zhao J , Domen K , Chem Yan 2004 Mater. 16 846 -    DOI : 10.1021/cm035090w
Gandhe A. R , Fernandes J. B 2005 Bull. Catal. Soc. India 4 131 -
Gandhe A. R , Naik S. P , Kakodkar S. B , Fernandes J. B 2006 Catal. Commun. 7 285 -    DOI : 10.1016/j.catcom.2005.09.013
Wang Z. S , Huang C. H , Li F. Y , Weng S. F , Yang S. M 2001 J.Photochem. Photobiol. A: Chem. 140 255 -    DOI : 10.1016/s1010-6030(01)00411-7
Murugan A. V , Samuel V , Ravi V 2006 Mater. Lett. 60 479 -    DOI : 10.1016/j.matlet.2005.09.017
Anpo M , Dohshi S , Kitano M , Hu Y , Takeuchi M , Matsuoka M 2005 Ann. Rev. Mater. Res. 35 1 -    DOI : 10.1146/annurev.matsci.35.100303.121340
Klosek S , Raftery D 2001 J. Phys. Chem. B 105 2815 -    DOI : 10.1021/jp004295e
Wu J. C. S , Chen C. H 2004 J. Photochem. Photobiol. A: Chem. 163 509 -    DOI : 10.1016/j.jphotochem.2004.02.007
Joung S. K , Amemiya T , Murabayashi M , Itoh K 2006 Chem. Eur. J. 12 5526 -    DOI : 10.1002/chem.200501020
Umebayashi T , Yamaki T , Itoh H , Asai K 2002 Appl. Phys. Lett. 81 454 -    DOI : 10.1063/1.1493647
Ohno T , Mitsui T , Matsumura M 2003 Chem. Lett. 32 364 -    DOI : 10.1246/cl.2003.364
Lettmann C , Hildenbrand K , Kisch H , Macyk W , Maier W. F 2001 Appl. Catal. B: Environ 32 215 -    DOI : 10.1016/s0926-3373(01)00141-2
Burda C , Lou Y , Chen X , Samia A. C. S , Stout J , Gole J. L 2003 Nano Lett. 3 1049 -    DOI : 10.1021/nl034332o
Ariyo C , Gonzalez P , Holappa L 2004 VII International Conference on Molten Slags Fluxes & Salt The South African Instituteof Mining and Metallurgy Johannesburg Republic of SouthAfrica 125 -
Lee E. S 2004 Bull. Korean Chem. Soc. 25 859 -    DOI : 10.5012/bkcs.2004.25.6.859
Lee E. S 2002 J. Korean Ind. Eng. Chem. 13 224 -
Lee E. S 1996 J. Ind. Eng. Chem. 2 151 -
Valdes L. B 1954 Proc. IRE 42 420 -    DOI : 10.1109/JRPROC.1954.274680
Lee E. S 2008 J. Ind. Eng. Chem. 14 701 -    DOI : 10.1016/j.jiec.2008.02.011
Gandhe A. R , Fernandes J. B 2005 J. Solid State Chem. 178 2953 -    DOI : 10.1016/j.jssc.2005.06.034