Advanced
Physioelectrochemical Investigation of Electrocatalytic Oxidation of Saccharose on Conductive Polymer Modified Graphite Electrode
Physioelectrochemical Investigation of Electrocatalytic Oxidation of Saccharose on Conductive Polymer Modified Graphite Electrode
Journal of Electrochemical Science and Technology. 2015. Sep, 6(3): 88-94
Copyright © 2015, The Korean Electrochemical Society
This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0/) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : June 01, 2015
  • Accepted : June 22, 2015
  • Published : September 30, 2015
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
A. Naeemy
Departement of Chemistry, Faculty of Science, K. N. Toosi university of technology, Tehran, Iran
Anaeemy@yahoo.com
A. Ehsani
Departement of Chemistry, Faculty of Science, Qom university, Qom, Iran
Anaeemy@yahoo.com
M. Jafarian
Departement of Chemistry, Faculty of Science, K. N. Toosi university of technology, Tehran, Iran
M. Moradi
Departement of Chemistry, Faculty of Science, K. N. Toosi university of technology, Tehran, Iran

Abstract
In this study we investigated the electrocatalytic oxidation of saccharose on conductive polymer- Nickel oxide modified graphite electrodes based on the ability of anionic surfactants to form micelles in aqueous media. This NiO modified electrode showed higher electrocatalytic activity than Ni rode electrode in electrocatalytic oxidation of saccharose. The anodic peak currents show linear dependency with the square root of scan rate. This behavior is the characteristic of a diffusion controlled process. Under the CA regime the reaction followed a Cottrellian behavior and the diffusion coefficient of saccharose was found in agreement with the values obtained from CV measurements.
Keywords
1. Introduction
Electrocatalytic processes involving the oxidation of sugars are of great interest in many areas, ranging from medical applications to waste water treatment and from the construction of biological fuel cells to analytical applications in the food industry [1 - 3] . On the other hand, the electrochemical detection of carbohydrates are important in many areas [4] . The investigation of glucose electrochemical oxidation began in 1960s, and has remained a very active research area [5] . Bagotzky and Vassilyev [6] first reported the electro-oxidation behavior of glucose in an acidic medium. At about the same time, Bockris et al. [7] studied this reaction at high temperature in alkaline solutions. Considerable attention has been directed to the use of biofuel cells on account of their mild operating conditions and diverse applications [8] . Biofuel cell systems utilize biocatalysts such as enzymes and microorganisms as the electrocatalyst instead of transition metal catalysts that are utilized in the conventional fuel cell systems. Several organic compounds and especially biomass based compounds such as sugars and alcohols can be utilized in biofuel cells and in principle highly efficient energy conversion can be achieved compared to the transition metal-based fuel cells [9] . Different metal electrodes, Ni [10 - 12] , Au [13] , Pt [14] and Cu [15] provide simple way for the catalytic oxidation of carbohydrates at constant applied potentials. On Ni- and Cu-electrodes, compared to Pt- and Au-electrodes, the reaction is greatly enhanced as a result of their catalytic effect [16 , 17] . Previous studies provided evidence of a reaction mechanism involving electron transfer mediated by a surface-bound Ni 2+ /Ni 3+ (or Cu 2+ /Cu 3+ ) redox couple [16 , 17] .
Conducting electroactive polymers are novel materials which are either being successfully used or expected to find use in various fields of many technological applications [18] . Among many applications of conducting polymers, electrochemical sensor applications seem to be very promising. Electrodes, modified with conducting polymers, possess many interesting features that can be exploited for numerous electroanalytical and sensor applications. Particularly, elucidating the bioelectrochemistry and electroanalysis of biologically important substances, are under intense research with the use of chemically modified electrodes. Several conducting polymers, such as polypyrrole (PPy), polyaniline (PANI), polythiophene (PTH) and poly ortho amino phenol (POAP), have been already in extensive use in order to immobilize desired chemical species and enzymes for development of sensors [19 - 23] .
Moreover, the possibility of dispersing metallic particles inside the polymers gives electrodes with higher surface areas, enhanced electrocatalytic activities and facilitates electron transfer due to semi conducting properties [24 - 28] and change in fermi level toward the oxidation of organic molecules [29] . Organic-inorganic composite have attracted consid-erable attention as they can combine the advantages of both components and may offer special through reinforcing or modifying each other [30] . Electrodeposition is an effective way to make composite films with a large variety of tunable parameters and so has the advantage of convenient film control.
The purpose of the present work is to study the electrochemical oxidation of saccharose on a G/POAP-NiO film in a solution of 1 M NaOH aiming at the elucidation of the mechanism, derivation of the kinetic parameters of the process and the usefulness of the electrocatalytic process.
2. Experimental
- 2.1. Materials
Ortho amino phenol (OAP), Sodium hydroxide, lithium perchlorate, nickel nitrate, sodium dodecyl sulfate (SDS) and saccharose used in this work were Merck product of analytical grade and were used without further purification. Doubly distilled water and pyrrole was used throughout.
- 2.2. Apparatus
Electrochemical studies were carried out in a conventional three electrode cell powered by an electrochemical system comprising of EG&G model 273 potentiostat/galvanostat and Solartron model 1255 frequency response analyzer. The system is run by a PC through M270 commercial software via a GPIB interface. Saturated Calomel Electrode (SCE), a Pt wire and a graphite (G) electrode were used as the reference, counter and working electrodes, respectively. All studies were carried out at 298 ± 2 K.
- 2.3. Preparation of NiO-POAP electrodes via electrodeposition
Films of POAP were formed on the graphite surface using an OAP monomer solution (0.01 M OAP in 0.1 M LiClO 4 and 0.1 M HClO 4 ) and (0.01 M OAP in 0.1 M LiClO 4 , 0.1 M HClO 4 and 0.005 M SDS). The electropolymerization was carried out by potential cycling (40 cycles at a scan rate of 50 mV/s between -0.2 and 0.9 V versus SCE. In order to incorporate Ni (II) ions into the POAP film, the freshly electropolymerised graphite electrode was placed at open circuit in a well stirred aqueous solution of 0.1 mol L −1 Ni (NO3) 2 . Nickel was accumulated by complex formation between Ni (II) in solution and amines sites in the polymer backbone [31 , 32] in a given period of time. The polarization behavior was examined in 0.1 mol L −1 NaOH for G/POAP-NiO using cyclic voltammetry. This technique allows the oxide film formation in parallel with inspecting the electrochemical reactivity of the surface. Voltammograms were recorded by cycling the potential between 0.1 and 0.8 V at 100 mV s −1 until a stable voltammogram was obtained. A mixture of NiO 2 and NiO-OH may coexist in the films displayed characteristic NiO x electroactivities as previously reported for nickel oxides [25] .
3. Results and discussion
Figs. 1a , b presents cyclic voltammogram (CV) of a G/Ni- POAP and G/ Ni-SDS-POAP electrode in 0.1 M NaOH solution recorded at a potential sweep rate of 100 mV s −1 . In the sweep a pair of redox peaks is assigned to Ni 2+ / Ni 3+ redox couple in alkaline media. The larger Ni response at the G/Ni-SDS-POAP respect G/Ni- POAP electrode is proposed to be the SDS enhances the catalytic properties of nickel oxide through fine dispersion of the catalyst particles into the conductive polymer matrix to results in a drastic increase in surface area.
PPT Slide
Lager Image
Consecutive cyclic voltammogram of G/Ni-POAP (a) and G/Ni-SDS-POAP (b) electrodes in 0.1 M NaOH at a scan rate of 100 mV s−1.
Fig. 2a shows cyclic voltammograms of G/Ni-SDS-POAP and other electrodes in 0.1 M NaOH solution in the absence and presence of 0.003 M saccharose at a potential sweep rate of 10 mV s −1 . As can be seen in 0.003 M saccharose G/Ni-SDS-POAP electrode generates higher current density for electro-oxidation in NaOH solution. The histograms of these behavior and difference between different electrodes response are presented in Fig. 2b . The larger saccharose response at the G/Ni-SDS-POAP electrode is due to the composite material which enhances the catalytic properties of nickel oxide through fine dispersion of the catalyst particles into the conductive polymer matrix to results in a drastic increase in surface area. The electrocatalytic behavior of any material depends on various factors such as: (i) the position of the energy levels of the reactive species and the electrode material; (ii) the charge-transfer process across the electrode/electrolyte interface; (iii) the diffusion of the reactants into/near the electrode surface; and the surface morphology of the electrode. These results may be explained on the basis of electrochemical reactions at a semiconductor electrode. Here, POAP is considered as a p-type semiconductor. The impurity doping level will be situated above the uppermost valence level since POAP is a p-type material. Since the electrode is in an anodic condition, electrons are abstracted from the electrolyte and these combine with holes in the semiconductor. In the present study, it is therefore clear that charge transfer at the electrode/electrolyte interface has the most influence on the electro-oxidation of saccharose when using a semi-conducting polymer electrode. It should also be noted that such charge transfer processes are also important in electrochromism and photo-electrochemical effects. In the first step of charge transport within POAP films, which are considered to be p-type semiconductors where holes are majority carriers, there are two processes of importance, inter chain and intra chain transport. The intra chain transport of charge takes place along the main chain, which is facilitated due to extended conjugation. The inter chain charge transport occurs mainly across one chain to the other by hopping mechanism.
PPT Slide
Lager Image
cyclic voltammograms of G/Ni-SDS-POAP and other electrodes in 0.1 M NaOH solution in the absence and presence of 0.003 M saccharose at a potential sweep rate of 10 mV s−1.
Figs. 3a , b show cyclic voltammograms of G/Ni-POAP and G/Ni-SDS-POAP electrodes in the 0.1 M NaOH solution in the presence of various concentrations of saccharose at a potential sweep rate of 10 mV s −1 . At G/Ni-SDS-POAP electrodes, oxidation of saccharose appeared as a typical electrocatalytic response. The anodic charge increased with respect to that observed for the modified surface in the absence of saccharose and it was followed by decreasing the cathodic charge upon increasing the concentration of saccharose in solution. In the presence of 0.003 M saccharose with the potential sweep rate of 10 mV s −1 , the ratio of anodic to cathodic charge in the presence of saccharose was 89/8 while in its absence it was 72/63. Charge is obtained by integrating the anodic and cathodic peaks after background correction.
PPT Slide
Lager Image
cyclic voltammograms of G/Ni-POAP (a) and G/NiSDS-POAP (b) electrodes in the 0.1 M NaOH solution in the presence of various concentrations of saccharose at a potential sweep rate of 10 mV s−1.
The anodic current in the positive sweep was proportional to the bulk concentration of saccharose ( Fig. 3b inset) and any increase in the concentration of saccharose caused an almost proportional linear enhancement of the anodic current. So, catalytic electrooxidation of saccharose on G/Ni-SDS-POAP seems to be certain.
The decreased cathodic current that ensued the oxidation process in the reverse cycle indicates that the rate determining step certainly involves saccharose and that it is incapable of reducing the entire high valent nickel species formed in the oxidation cycle. The electrocatalytic oxidation of saccharose occurs not only in the anodic but also continues in the initial stage of the cathodic half cycle. Saccharose molecules adsorbed on the surface are oxidized at higher potentials parallel to the oxidation of Ni(II) to Ni(III) species. The later process has the consequence of decreasing the number of sites for saccharose adsorption that along with the poisoning effect of the products or intermediates of the reaction tends to decrease the overall rate of saccharose oxidation. Thus, the anodic current passes through a maximum as the potential is anodically swept. In the reverse half cycle, the oxidation continues and its corresponding current goes through the maximum due to the regeneration of active sites for adsorption of saccharose as a result of the removal of adsorbed intermediates and products. Surely, the rate of saccharose oxidation as signified by the anodic current in the cathodic half cycle drops as the unfavorable cathodic potentials are approached.
Fig. 4 shows the cyclic voltammograms of G/Ni-SDS-POAP electrode in 0.1 M NaOH in presence of 0.001 M saccharose at a scan rate of 10 mV s −1 for 400 cycles. It is observed that the current density of electro-oxidation of saccharose is almost constant in 400cycles due to the stability of electrocatalyst in this cycle number and indicating that saccharose reacted with the surface and no poisoning effect on the surface was observed.
PPT Slide
Lager Image
Repeated cyclic voltammograms of 0.001 M saccharose oxidation on G/Ni-SDS-POAP electrode at 10 mV s−1, cycle number: 1, 5, 10, 50, 100, 150, 200, 250, 300, 400.
Chronoamperograms were recorded by setting the working electrode potentials to the desired values and measuring the catalytic rate constant on the G/Ni-SDS-POAP electrode surface. Fig. 5a presents chronoamperogram for the G/Ni-SDS-POAP electrode in the absence and presence of saccharose over the concentration range 0.0 - 0.006M. The applied potential step was 540 mV. Plotting the net currents versus the minus square roots of time results in linear dependencies ( Fig. 5b ). Therefore, a diffusion-controlled process is dominant for electrooxidation of drugs. By using the slopes of these lines, we can obtain the diffusion coefficients of the drugs according to the Cottrell equation [33] :
PPT Slide
Lager Image
(a); Double steps chronoamperograms of G/NiSDS-POAP electrode in the absence and presence of saccharose over the concentration range 0.0-0.006M. (b); the net currents versus the minus square roots of time for the chronoamperogram presented in Fig. 5a.
PPT Slide
Lager Image
where D is the diffusion coefficient, and C* is the bulk concentration. The mean values of the diffusion coefficients for saccharose were 4.26×10 −6 cm 2 s on the G/Ni-SDS-POAP surface. Chronoamperometry can also be used to evaluate the catalytic rate constant according to [33] .
PPT Slide
Lager Image
where I cat and I L are the currents in the presence and absence of the saccharose, respectively, and γ = k 0 Ct is the argument of the error function. k 0 is the catalytic rate constant, and t is elapsed time. In cases where γ > 1.5, erf( γ 1/2 ) is almost equal to unity, and Eq. (2) can be reduced
PPT Slide
Lager Image
From the slopes of the I cat / I L versus t 1/2 plots, the mean values of k 0 obtained for saccharose were 7.86 × 10 4 cm 3 mol −1 s −1 and 7.24 × 10 4 cm 3 mol −1 s −1 in the surface of G/Ni-SDS-POAP and G/Ni-POAP electrodes respectively.
Electrochemical impedance spectroscopy is one of the best techniques for analyzing the properties of conducting polymer electrodes and charge transfer mechanism in the electrolyte/electrode interface. It has been broadly discussed in the literature using a variety of theoretical models. Fig. 6 shows the Nyquist diagrams of G/Ni-SDS-POAP electrodes recorded at the oxidation peak potential of saccharose as dc-offset. Diagrams of G/Ni-SDS-POAP consist of a small semicircle terminated to depressed capacitive semicircles at low frequency end of the spectrum. The equivalent circuit compatible with the Nyquist diagram recorded in the presence of saccharose was depicted in Fig. 6 . To obtain a satisfactory impedance simulation of methanol electro-oxidation, it is necessary to replace the capacitor C with a constant phase element ( CPE ) in the equivalent circuit [34 - 46] . The most widely accepted explanation for the presence of CPE behavior and depressed semicircles on solid electrodes is microscopic roughness, causing an inhomogeneous distribution in the solution resistance as well as in the double-layer capacitance. The parallel combination of charge transfer resistance R 1 and constant phase element CPE 1 accounts for the injection of electrons from the conductive polymer to the back metallic contact. R 2 and CPE 2 represent the saccharose oxidation.
PPT Slide
Lager Image
Nyquist diagrams of G/Ni-SDS-POAP electrodes recorded at the saccharose oxidation peak potential as dcoffset for 0.001 M saccharose.
A number of mechanisms have been proposed for the electro- oxidation of alcohols on Ni in alkaline solutions. While Fleischmann et al. [33] assumed catalytic/intermediate role for NiOOH in the course of an anodic potential sweep.
On the basis of our study and consistent with the literature [28 , 33 , 47 , 48] the following mechanism is proposed for the mediated electro-oxidation of saccharose on G/Ni-SDS-POAP and the corresponding kinetics is formulated. The redox transition of nickel species present in the film is
PPT Slide
Lager Image
and saccharose is oxidized on the modified surface via the following reaction
PPT Slide
Lager Image
PPT Slide
Lager Image
where Ni 3+ sites are regenerated by the power source and on the Ni 3+ oxide surface by direct electro-oxidation
PPT Slide
Lager Image
PPT Slide
Lager Image
Eqs. (5) and (6) are according to Fleischmann mechanism and in Eqs. (7) and (8), Ni 3+ used as active surface for saccharose oxidation.
4. Conclusion
POAP was formed by cyclic voltammetry in monomer solution containing sodium dodesyl sulfate (SDS), on graphite (G) electrode surface. Then, Ni(II) ions were incorporated to electrode by immersion of the polymeric modified electrode having amine group in Ni(II) ion solution. The morphologies and elemental components of the film were inspected by scanning electron microscopy and EDS respectively. The nickel oxide film was tested for electro-oxidation of saccharose in alkaline media. The modified electrodes showed electrocatalytic activity for the oxidation of saccharose.
Acknowledgements
The authors would like to express their deep gratitude to the Iranian Nano Council for supporting this work.
References
Johnson D.C. , LaCourse W.R. 1995 Carbohydrate Analysis Elsevier Science Amsterdam
Katz E. , Willner I. , Kotlyar A.B. 1999 J. Electroanal. Chem. 479 64 -    DOI : 10.1016/S0022-0728(99)00425-8
Khoo S.B. , Yap M.G.S. , Huang Y.L. , Guo S.X. 1997 Anal. Chim. Acta. 351 1331 -
Johnson D.C. , Weber S.G. , Bond A.M. , Wightman R.M. , Shoup R.E. , Krull I.S. 1986 Anal. Chim. Acta 180 187 -    DOI : 10.1016/0003-2670(86)80007-1
Lei H.W. , Wu B.L. , Cha C.S. , Kita H. 1995 J. Electroanal. Chem. 382 103 -    DOI : 10.1016/0022-0728(94)03673-Q
Bagotzky V.S. , Vassilyev Yu.B. 1964 Electrochim. Acta 9 1329 -    DOI : 10.1016/0013-4686(64)87009-2
Bockris J.O’M. , Piersma B.J. , Gileadi E. 1964 Electrochim. Acta 9 1329 -    DOI : 10.1016/0013-4686(64)87009-2
Ikeda T. , Kano K. 2003 Biophys. Acta 1647 121 -
Bullen R.A. , Arnot T.C. , Lakeman J.B. , Walsh F.C. 2006 Biosens. Bioelectron. 21 2015 -    DOI : 10.1016/j.bios.2006.01.030
Zhao C. , Shao C. , Li M. , Jiao K. 2007 Talanta 71 1773 -
Morita M. , Niwa O. , Tou S. , Watanabe N. 1999 J. Chromatogr. A 837 17 -    DOI : 10.1016/S0021-9673(99)00047-3
Fleischmann M. , Korinek K. , Pletcher D. 1971 J. Electroanal. Chem. 31 39 -    DOI : 10.1016/S0022-0728(71)80040-2
Hilmi A. , Luong J.H.T. 2000 Anal. Chem. 72 4677 -    DOI : 10.1021/ac000524h
Skou E. 1977 Electrochim. Acta. 22 313 -    DOI : 10.1016/0013-4686(77)85079-2
Colon L.A. , Dadoo R. , Zare R.N. 1993 Anal. Chem. 65 476 -    DOI : 10.1021/ac00052a027
Fleischmann M. , Korinek K. , Pletcher D. 1972 J. Chem. Soc. Perkin Trans. 2 1396 -
Luo P.F.F. , Kuwana T. 1994 Anal. Chem. 66 2775 -    DOI : 10.1021/ac00089a028
Singh V. , Mohan S. , Singh G. , Pandey P.C. , Prakash R. 2008 Sens. Actuators B 132 99 -    DOI : 10.1016/j.snb.2008.01.007
Mokrane S. , Makhloufi L. , Hammache H. , Saidani B. 2001 J. Solid State Electrochem. 5 339 -    DOI : 10.1007/s100080000161
Upadhyay D.N. , Kolb D.M. 1993 J. Electroanal. Chem. 358 317 -    DOI : 10.1016/0022-0728(93)80447-P
Chen J. , Too C.O. , Wallace G.G. , Swiegers G.F. , Skelton B.W. , White A.H. 2002 Electrochim. Acta 47 27 -
Pandey P.C. , Upadhyay S. , Singh G. , Prakash Rajiv , Srivastava R.C. , Seth P.K. 2000 Electroanalysis 12 517 -    DOI : 10.1002/(SICI)1521-4109(200005)12:7<517::AID-ELAN517>3.0.CO;2-Y
Banik R.M. , Prakash Mayank, R. , Upadhyay S.N. 2008 Sens. Actuators B 131 295 -    DOI : 10.1016/j.snb.2007.11.022
Mahjani M.G. , Ehsani A. , Jafarian M. 2010 Synth. Met. 160 1252 -    DOI : 10.1016/j.synthmet.2010.03.019
Ehsani A. , Mahjani M. G. , Jafarian M. , Naeemy A. 2012 Electrochimica. Acta. 71 128 -    DOI : 10.1016/j.electacta.2012.03.107
Feizbakhsh A.R. , Naeemy A. , Ehsani A. , Aghasi A. , Danaee I. 2012 J. Chin. Chem. Soc. 59 1086 -    DOI : 10.1002/jccs.201100570
Ehsani A. , Mahjani M.G. , Jafarian M. 2011 Synth. Met. 161 1760 -    DOI : 10.1016/j.synthmet.2011.06.020
Ehsani A. , Mahjani M. G. , Jafarian M. , Naeemy A. 2010 Progress in organic coating 69 510 -    DOI : 10.1016/j.porgcoat.2010.09.007
Radhakrishnan S. , Adhikari A. , Awasti DK. 2001 Chem. Phys. Lett. 341 518 -    DOI : 10.1016/S0009-2614(01)00547-4
Berchmans S. , Gomathi H. , Rao GP. 1995 J. Electroanal. Chem. 394 267 -    DOI : 10.1016/0022-0728(95)04099-A
Ojani R. , Raoof J.-B. , Fathi S. 2009 Electrochim. Acta 54 2190 -    DOI : 10.1016/j.electacta.2008.10.023
Eramo F.D. , Marioli J.M. , Arevalo A.A. , Sereno L.E. 1999 Electroanalysis 11 481 -    DOI : 10.1002/(SICI)1521-4109(199906)11:7<481::AID-ELAN481>3.0.CO;2-7
Bard A.J. , Faulkner L.R 2001 Electrochemical Methods Wiley New York
Ehsani A. , Mahjani MG. , Jafarian M. 2012 Synth. Met. 162 199 -    DOI : 10.1016/j.synthmet.2011.11.032
Ehsani A. 2015 Prog. Org. Coat 78 133 - 139    DOI : 10.1016/j.porgcoat.2014.09.015
Ehsani A. , Mahjani MG. , Bordbar M. , Adeli S. 2013 J. Electroanal. Chem. 710 29 -    DOI : 10.1016/j.jelechem.2013.01.008
Ehsani A. , Mahjani M.G. , Jafarian M. 2011 J. Chem. 35 1 -
Ehsani A. , Mahjani M.G. , Adeli S. , Moradkhani S. 2014 Prog. Org. Coat. 77 1674 -    DOI : 10.1016/j.porgcoat.2014.05.027
Ehsani A. , Mahjani MG. , Moshrefi R. , Mostaanzadeh H. 2014 J. Shabani Shayeh, RSC. Adv. 4 2231 -
Ehsani A. , Nasrollahzadeh M. , Mahjani MG. , Moshrefi R. , Mostaanzadeh H. 2014 Ind. Eng. Chem. 20 4363 -    DOI : 10.1016/j.jiec.2014.01.045
Ehsani A. , Mahjani M.G. , Nasseri M. , Jafarian M. 2014 Methods Mater. 61 146 -
Ehsani A. , Jaleh B. , Nasrollahzadeh M. 2014 J. Power Sources. 257 300 -    DOI : 10.1016/j.jpowsour.2014.02.010
Ehsani A. , Adeli S. , Babaei F. , Mostaanzadeh H. , Nasrollahzadeh M. 2014 J. Electroanal. Chem. 713 91 -    DOI : 10.1016/j.jelechem.2013.12.003
Naghdi S. , Jaleh B. , Ehsani A. 2015 Bulletin of the Chemical Society of Japan 88 722 -    DOI : 10.1246/bcsj.20140402
Ehsani A. , Moshrefi R. , Ahmadi M. 2015 Electrochemical Science and Technology 6 (1) 7 -
Ehsani A. , Babaei F. , Mostaanzadeh H. 2015 J. of the Brazilian Chem. Soc. 26 331 -
Ehsani A. , Mahjani M G. , Babaei F. , Mostaanzadeh H. 2015 RSC Advances 5 30394 -    DOI : 10.1039/C5RA02297E
Ehsani A. , Vaziri-Rad A. , Babaei F. , Shiri H. Mohammad 2015 Electrochim. Acta 159 140 -    DOI : 10.1016/j.electacta.2015.01.204