Advanced
Eco-friendly selection of ship emissions reduction strategies with emphasis on SOx and NOx emissions
Eco-friendly selection of ship emissions reduction strategies with emphasis on SOx and NOx emissions
International Journal of Naval Architecture and Ocean Engineering. 2014. Sep, 6(3): 737-748
Copyright © 2014, The Society of Naval Architects of Korea
This is an Open-Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Published : September 30, 2014
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Ibrahim S. Seddiek
Department of Marine Engineering Technology, Arab Academy for Science, Technology & Maritime Transport, Alexandria, Egypt
Mohamed M. Elgohary
Department of Naval Architecture and Marine Engineering, Faculty of Engineering, Alexandria University, Alexandria, Egypt
Abstract
Increasing amounts of ships exhaust gases emitted worldwide forced the International Maritime Organization to issue some restricted maritime legislation for reducing the adverse environmental impacts arising from such emissions. Consequently, ships emission reduction became one of the technical and economical challenges that facing the ships, operators. The present paper addresses the different strategies that can be used to reduce those emissions, especially nitrogen oxides and sulfur oxides. The strategies included: applying reduction technologies onboard, using of alternative fuels, and follows one of fuel saving strategies. Using of selective catalytic reduction and sea water scrubbing appeared as the best reduction technologies onboard ships. Moreover, among the various proposed alternative fuels, natural gas, in its liquid state; has the priority to be used instead of conventional fuels. Applying one of those strategies is the matter of ship type and working area. As a numerical example, the proposed methods were investigated at a high-speed craft operating in the Red Sea area between Egypt and the Kingdom of Saudi Arabia. The results obtained are very satisfactory from the point of view of environment and economic issues, and reflected the importance of applying those strategies .
Keywords
INTRODUCTION
All over the study of properties, advantages and drawbacks of the different conventional marine fuels (Diesel oil and heavy fuel oil) , it can be showed that the traditional liquid marine fuels have worked competently through the most recent decades, particularly with regard to adaptability, performance, safety and the compliance with the emissions regulations. But in the last few years, some troubles have appeared due to its use, these include: the barriers of compliance with the new emissions regulations ( Fotis et al., 2014 ), the increase of the fuel cost, which presents the main element in the ships operating cost ( Banawan et al., 2013 ) and finally the sustainability issue ( Seddiek et al., 2013 ). Uncontrolled emissions from burning traditional marine fuel oils onboard ships have a significant impact upon our environment, especially with increase quantity of ship emissions: Nitrogen oxides (NOx), Sulfur oxides (SOx), Di-oxide (CO 2 ), Mono-oxide (CO), Particulates Matter (PM) and Hydrocarbons (HC) ( Welaya et al., 2013 ). A more comprehensive review was recently carried out by various organizations which are concerned with air pollution and discussed health and welfare impacts from burning the fuel oils and quantified the financial benefits that result from reducing these emissions ( Beecken et al., 2014 ). As a method toward ship emissions reduction, nowadays, the IMO regulations pushed the ships to use expensive fuel type in Ship Emissions Control Areas (SECAs) and will be forced to be worldwide by year 2020 ( Herdzik, 2011 ). Moreover, Marine Environment Protection Committee (MEPC) in its 57 th session planned to reduce NOx emissions to the lowest level by year 2016. There is no doubt that this will effect negatively in the ship economic due to the increase of operating cost, which encourage all who interest in marine field to search and present different proposals to find a solution for this problem. Thus, many attempts are carried out to search for a solution for that issue. The present paper discusses this issue from the point of view of statistics, regulations, and the proposed strategies for achieving this target.
STATISTICS AND REGULATIONS OF SHIPS, EMISSIONS
Several inventory studies suggested that in 2000, ocean-going ships have emitted around (600-900) thousands tones of CO 2 , 15% of all global NOx emissions and 4-9% of global SO 2 emissions ( Welaya et al., 2013 ). While in 2007, the quantity of gases emitted from ships estimated to be 25 and 15 million tons of NOx and SOx respectively, and have estimated around 2.7% of all global CO 2 are attributable to ships ( IMO, 2009 ). Other studies revealed that shipping-related PM emissions are responsible for 3-8% of global P.M 2.5 -related mortalities ( Eide et al., 2013 ).
IMO regulations regarding nitrogen oxides had planned to achieve NOx emissions reduction through three Tiers. Tier I for ships keel lay-down after 1January 2000, Tier II , for ships keel lay-down after 1January 2011, which requires achievement of 15% emissions reduction of Tier I, and lastly Tier III for ships keel lay-down after 1January 2016 with 85% emissions reduction of Tier I ( Lin and Lin, 2006 ). The current allowable NOx emission level according to IMO regulation depends on the speed category of the engine and ranges from (17 g/kWh ) for engine speed 130r/min to (9.984 g/kWh ) for engine speed 2000 r/min ( IMO, 2009 ). Annex VI regulations of Marine Pollution (MARPOL) prevention convention on sulfur oxide requiring a maximum 3.50% content sience 1 January 2012 and 0.50% by 1 January 2020 globally. Moreover, Annex VI also imposed a 1.5% sulfur limit on marine fuels in Emission Control Areas (ECAs) effective since May 2006, this limit was reduced to 1.0% sulfur effective from 1 July 2010 and will be further reduced to 0.1% sulfur beginning January 2015 ( Gritsenko and Yliskyla, 2013 ; Herdzik, 2011 ). Regarding HC emissions; MEPC in its 57 th session ( IMO, 2008a ) showed the importance of decreasing availability of halons gas in addition to prohibit any new installations containing ozone-depleting substances on all ships by year 2020. So, this session, presented amended regulation 14, for P.M emissions, which in conjunction with SOx limitations (as minimizing of fuel sulfur content leads to reduction of PM emissions). Furthermore, MEPC 58 th session ( IMO, 2008b ) introduced the Energy Efficiency Design Index (EEDI) as a theoretical measure for the mass of CO 2 emitted per unit of transport work (grams CO 2 per ton nautical mile) but until now there is no certain mandatory limit ( Seddiek et al., 2013 ).
METHODS OF SHIP EMISSIONS REDUCTION
To carry out ships emission reduction process, a set of techniques could be done separately or as a complex concept, including using of: emissions reduction technology, alternative fuels, and fuel saving strategies, as follows:
- Ship emissions reduction based on applying reduction technologies onboard
Technologies for emissions reduction can be divided into three general areas: In -engine, Fuel -related and Exhaust cleaning technologies. The most emissions reductions technologies are concerned with NOx and SOx emissions due to their bad effect on the marine environment ( Seddiek et al., 2013 ).
- NOx emissions reduction technology
Many researches ( Stationary, 2000 ; Andersson and Winnes, 2011 ; Lamas and Rodriguez, 2012 ; Lamas et al., 2013 ) showed the possibility of achieving acceptable NOx emissions reduction. One of the old methods that used was adding water to the liquid fuel ( Genesis Engineering Inc., 2003 ). So, using the puriNOx product, who mix Lubrizol, s proprietary additives with liquid fuels to form a stable product may cause reduction of about 20% & 50% for NOx and P.M respectively ( Stationary, 2000 ). Recently, it was shown by ( Lamas et al., 2013 ) that several engine’s internal modifications may achieve NOx reduction by considerable percentage. Practically, Selective Catalytic Reduction (SCR) system is currently used onboard many ships and considered the best efficient method of NOx reduction than the other methods due to its durability and compliance with most commercial ships ( Andersson and Winnes, 2011 ; Woodyard, 2004 ).
- SOx emissions reduction technology
Some, attempts are carried out for improving of marine fuel oil regarding SOx emissions for a clean environment and for keeping the running cost as low as possible. One of these attempts is mixing heavy fuel oil with thermal oil processed from Waste Plastics, but practically it was too difficult due to some technical problems ( Banawan et al., 2010 ). Worldwide concerns about emissions of SOx emissions from marine vessels have created an impetus to replace high sulfur marine residual oil with cleaner lower sulfur fuels. Two such fuels being discussed as substitutes for residual oil are Marine Gas Oil (MGO) and marine diesel oil (MDO) ( Bengtsson et al., 2011 ). Moreover, seawater scrubbing system appeared as an efficient SOx emissions reduction ( Andreasen and Mayer, 2007 ). Widespread adoption of seawater scrubbing will likely be dependent upon satisfactory resolution of the issue of its impact on water quality and ship operating cost ( Johansson et al., 2013 ). The IMO MARPOL regulations, the European Union (EU) regulations and the US EPA regulations are aligned except on some points of detail. They all allow for equivalents and so permit the use of Exhaust Gas Cleaning Systems (EGCS), which are called scrubbers. They have to achieve the same limits on SOx content of the exhaust whatever fuel is burnt as if the ship was burning fuel with a sulfur content less than 0.1%. Each scrubber also has to be approved as an equivalent by the flag administration of the vessel so some different flag state requirements may apply.
- Other emissions reduction technology
In addition to the technologies used to reduce both NOx and SOx, there are some other technologies which are used for other pollutants such as P.M, CO 2 and HC. A less concern is paid for those pollutant comparative with NOx and SOx emissions. This is due to the fact that NOx and SOx emissions have the higher negative effect towards environment and human health issues. The most common technologies used for PM emissions reductions are using of: low sulfur fuel oil, and catalyzed particulate filter ( Daniel et al., 2012 ). CO emissions reduction achieved through improving the process of fuel combustion inside the engines to insure the complete combustion process. Moreover, reduction of CO 2 and HC will be achieved as a part of whole ship’s emissions reduction technology ( Seddiek et al., 2012 ; Banawan et al., 2013 ). Currently, a combined SCR systems can be used for reducing NOx, CO, and HC emissions together. This systems work in two efficient stages, the oxidation stage for CO and HC emissions reduction and the SCR stage provide NOx emissions reduction. Applying the basic or combined SCR system is the matter of economic considerations and the essential of a certain emissions reduction. Table 1 summarizes the average emissions reduction percentages as a result of using the mentioned and other emissions reduction technologies for marine diesel engines.
Available methods for reducing ship emissions (Buhaug et al., 2009;EPA, 2009;Ariana et al., 2006;Woodyard, 2004).
PPT Slide
Lager Image
*Switching from residual fuel to distillate fuel
- Ships emissions reduction based on using of alternative fuels
The main alternative marine fuel types may be found in two forms - liquid and gaseous fuels. Liquid marine alternative fuels include: Methanol, Ethanol, and Bioliquid fuel, among them methanol has the promise to use for marine application in the future ( Kolwzan et al., 2012 ). On the other hand, the main alternative gasses fuels include: Hydrogen, Propane, and natural gas. Among the previous types, Hydrogen and natural gas showed many attempts to applied onboard ships, and more emphasis on those fuels regarding their characteristics can be illustrated as follows:
- Hydrogen
A variety of alternative hydrogen energy production technologies are available in practice, including: Steam reforming, Off-gas cleanup, Electrolysis Photo process, thermo chemical process and Partial oxidation of hydrocarbons ( Hagh, 2004 ). Until now the use of hydrogen as a main fuel for marine power plants is very restricted due to some technical problems ( Christos et al., 2014 ).
- Natural gas
The use of natural gas also offers a number of environmental benefits over other fossil fuels, particularly liquid fuels ( Elma et al., 2014 ; Seddiek et al, 2013 ; Banawan et al., 2010 ). The combustion of natural gas releases very small amounts of sulfur dioxide and nitrogen oxides, virtually no ash or particulate matter and lower the levels of carbon dioxide, carbon monoxide, and other reactive hydrocarbons ( Bengtsson, 2011 ). Many researchers showed the possibility of using natural gas for marine application either for ships powering system ( El-Gohary, 2012 ; El-Gohary and Seddiek, 2013 ) or for electric generation, using fuel cells ( Welaya et al., 2011 ; 2013 ). The compression had been presented by ( Radwan et al., 2007 ; Banawan et al., 2010 ) among the most marine alternative fuels and the other one, which was presented by ( Bengtsson et al., 2011 ) between current onboard fossil fuel and liquefied natural gas indicated that NG considers the best alternative fuel for marine applications.
- Ships emissions reduction based on fuel saving strategies
Several studies, aiming to saving and reducing fuel consumption and consequently exhaust gases emissions onboard ships, have shown that there are different methods to achieve that. The present section describes some of the main strategies which may be applicable onboard ships in order to achieve maximum fuel saving.
- Ship resistance reduction
Ship's fuel consumption is a part of ship's powering calculation, which depends mainly on the ship's resistance. There are many options to reduce ship resistance, such as anti-fouling, ship's weight reduction as traditional methods ( Apostolos, 2010 ; TAYLAN, 2010 ; Philippe, 2009 ) and air bubbles as a new concept ( Winkler, 2009 ). Each method of them can contribute by different fuel saving percentages according to ship type.
- Renewable energy
Although there is a high degree of preference for renewable energy over fossil fuels as energy source for ship power, the study of development of a renewable infrastructure for marine transportation is still in the first steps. Wind energy, Solar energy, Wave energy, and Hydrogen combustion present the most common sources of renewable energy that may be used onboard ships ( Alexandros et al., 2010 ; Mekhilef et al., 2011 ).
- Energy performance improvement
The contribution of marine power plant efficiency in issue of fuel saving may be achieved through fuel quality improvement and engine tuning process ( Rosli, 2008 ; Fredrik, 2008 ). Engine tuning process can be achieved through tuning of fuel system, air system, and exhaust system.
- Energy conservation management
In the maritime field, energy conservation and management processes onboard ships are made more efficient, concerning the fuel to help stretch the fuel budget as far as possible and make ships more environmentally friendly ( Oihane et al., 2012 ; Gerasimos and George, 2013 ; Kjeld, 2009 ; Elgohary, 2009 ). One of the new proposed waste heat recovery application was presented by ( Seddiek et al., 2012 ), which showed the possibility of using exhaust gases to operate absorption air condition unit.
- Reduce ship speed
Fuel consumption and the amount of ships exhaust gas emissions are in direct relation. Consequently, saving any amount of ship fuel consumption will affect positively on marine environment ( Harilaos et al., 2009 ). Furthermore, with the continuous fuel price increment, some companies forced to reduce their ships speed ( Shuaian and Qiang, 2012 ). An estimate of fuel saving percentage as a result of speed reduction was introduced and expressed by ( Banawan et al., 2013 ):
- Shore side power connection
A huge amount of fuel is consumed by auxiliary engines at the ports. (P.M) emissions are responsible for approximately 60000 cardiopulmonary and lung cancer deaths annually, with most of those deaths occurring along the coasts ( Yang et al., 2011 ). Shore power connection system used to saving the quantity of fuel consumption through ships berthing periods. The economical and environmental benefits due to applying of shore power connection were demonstrated by ( Hall, 2010 ; Seddiek et al., 2013 ).
CHOICE OF THE SUITABLE EMISSIONS REDUCTION METHOD
There are many factors affecting choice of the suitable ship emissions reduction method which include ship type, power rating, economic issue, adaptability, and compliance with the current and future emission regulations. As a case study, the present paper handling this factors in case of applying the previous methods onboard high speed passenger ships Choice of these types is the matter of power rating which conjuncts directly with the amount of exhaust gas emitted from ships. Moreover, these ships call ports on more regular basis in short time compare to any other ships which make them more effect in the health of population at the areas near from ports. According to the nature of ships, operating and based on the previous researches, carried out by ( Elma et al., 2014 ; Christos, 2014 ; Johansson et al., 2014 ) using of alternative fuels and emission reduction technologies seem the most suitable methods to be applied for passenger ships, especially from the point of view of applicability.
CASE STUDY
In recent years, the number of short-voyage passenger ships sailing in the Red Sea area has increased. There is no doubt that these ships have contributed to develop maritime transport in this area. On the other hand, it was shown by ( Seddiek et al., 2012 ; Seddiek et al., 2013 ) that the high power of these ships contributed to the increasing gaseous emission rate and affect adversely on the environment in this area. The present paper discusses the viability of applying the mentioned two methods onboard one of the high-speed crafts operating in the Red Sea area, called Alkahera, as shown in Fig. 1 . The ship operates between Hurghada port in Egypt and Duba port in the Kingdom of Saudi Arabia. The ship's technical data is summarized as shown in Table 2 .
PPT Slide
Lager Image
High-speed craft Al-Kahera.
M/V Alkahera main technical data.
PPT Slide
Lager Image
M/V Alkahera main technical data.
- Applying emissions reduction technologies
Fig. 2 shows a simple scheme for emissions reduction model, which can be installed onboard the case. It consists of SCR system for NOx emissions reduction , followed by sea water scrubber system. The present study had been relied on the characteristic and performance of ship’s main engines, SCR system, and Scrubber system. All data were computed using Engineering Equations Solver (EES) program for environmental and economic results.
PPT Slide
Lager Image
Simple model of main components for SCR & water scrubber system inside engine room.
To evaluate the importance of installation of SCR and sea water scrubber system from the view point of environment; quantity of ship's emissions that could be reduced in case of applying these systems may be estimated from the following equation for both NOx and SOx emissions.
PPT Slide
Lager Image
where ( ERQ ) emission reduction quantity is ( Lf ) is load factor, ( Ef ) is emission factor, ( Rp ) is emissions factor reduction percentage due to installation of SCR, ( P ) engine power rating, ( tT ) ship sailing time. On the other hand, the main draw-back of applying these systems is the additional annual costs. Economically, applying SCR system will show some extra costs including: Urea consumption, investment costs , running costs (urea) and maintenance cost. Moreover, the main component of the catalyst requires rebuilding depending on the type of fuel during operation. There is noticeable uncertainty concerning the time estimate; this study assumes a grim window of 5 years and these costs may be expressed as follows:
PPT Slide
Lager Image
where ( Ci ) is total capital installation cost, which depends on fuel sulfur content, ( N ) ship working years after installation, ( i ) interest percent, ( CO ) annual maintenance cost , ( FC ) fuel cost increment in case of using marine gas oil, ( CM ) annual operating cost. Take into consideration that the life time of SCR will depends on sulfur content.
- Applying alternative fuels
Discussion of using alternative fuels as a strategy for ship emissions reduction revealed that natural gas appears as the most common alternative fuel onboard ships. One of the most outcomes of applying this strategy is the environmental benefit, which may be quantified as follows:
PPT Slide
Lager Image
where LfDO and EfDO are load factor, emission factor in case of diesel engines. So, LfDO and EfNG are load factor, emission factor for natural gas, while C 1 and C 2 are percentage of diesel oil and natural gas in case of dual-fuel engines. It should be taken into consideration that using of natural gas will be during sailing only. The typical exhaust gas compositions of burning diesel fuel inside marine internal combustion engine can be tabulated as shown in Table 3 . Moreover, consumed power, specific fuel consumption, and emissions Factors of diesel and dual-fuel natural gas engines can be illustrated as shown in Table 4 ( Banawan et al., 2010 ; Seddiek et al., 2013 ).
Typical composition of exhaust gases.
PPT Slide
Lager Image
Typical composition of exhaust gases.
Engines data and emissions factors.
PPT Slide
Lager Image
Engines data and emissions factors.
To adapt the diesel engine to dual-fuel (diesel -methane) engine, a conversion process should be carried out. This includes modification of the main engines parts such as (fuel injector, piston, and valves). In addition, adding NG supply system including NG storage spaces, supply piping and valves, gas detection units and alarms, exhaust ventilation system, and other minor components. Cost analysis of using natural gas, in form of Liquefied Natural Gas (LNG): instead of diesel oil onboard ships it depends on some essential items, including the present and future of diesel fuel prices trend, cost of conversion onboard diesel engine to dual-fuel engine and the difference in maintenance, operation and bunkering costs.
The annual saving or increment cost [ ACI ] due to shifting to natural gas may be expressed as follows:
PPT Slide
Lager Image
where, ( CA ) the capital cost of conversion from diesel oil to dual-fueled engine, ( N ) is the expected working years after conversion process, ( i ) annual interest ( FSC ) the difference between fuel cost of diesel and natural gas, (Δ bunkering) is the difference cost between ship bunkering process of diesel oil and NG and ( SCM&O ) the difference between maintenance and operating cost of diesel and natural gas engines. Moreover, annual fuel cost difference ( FSC ) could be estimated as follows:
PPT Slide
Lager Image
where, ( sfcD.O ), and ( fcD.O ) are specific fuel consumption, and fuel cost of diesel fuel oil. ( sfcLNG ), ( fcLNG ), and ( D.Op ) are specific fuel consumption, fuel cost, diesel oil percent in case of dual-fuel. LNG fuel cost is different from area to other worldwide taking various factors into account such as cost of production, liquefaction, logistic, and bunkering process. The fuel price, in 2013, was about 11-12 USD/mmBTU for LNG ( Harsema, 2013 ) and nearly 20 USD/mmBTU for marine diesel oil ( Bunker world, 2014 ). Figs. 3 and 4 represent the environmental and economic outcome due applying the emissions reduction strategies. It can be noticed that applying of those strategies will achieve nearly the same emission reduction regards NOx, SO X , and P.M emissions. On the other hand, LNG will achieve more CO 2 reduction and cause more HC emissions as shown in Fig. 3 .
PPT Slide
Lager Image
Ship’s emission reduction @ various strategies.
PPT Slide
Lager Image
Ship’s Cost saving @ various strategies.
As the present paper emphasis on SOx and NOX emissions; using of the basic type of SCR (which designed mainly for NOx emissions) will be considered rather than using of the combined system which is more expensive than the basic system. From Fig. 3 it can be noticed that the higher NOx emissions reduction percentage could be done through using of (SCR + MGO) system, while applying of (SCR + Sea water scrubber) system which may achieve maximum SOx and HC emissions reduction. On the other hand using of natural gas as alternative fuel will contribute in reducing CO 2 emissions more than any other proposed system. A part of this conclusion is due to the fact that NG has lower Carbone content than diesel oil and consequently the combustion of these products of it will contain less CO 2 emissions. On the other hand, HC emissions will increase when using NG instead of diesel oil as the main fuel in internal combustion engines, since diesel engines are operated at a much leaner mixture than NG engines are, especially for converted engines ( Banawan et al., 2010 ).
Economically, Fig. 4 presents the average cost saving or increment due to applying the proposed emissions reduction strategies. From the Figure it can be excluded that using of natural gas as an alternative fuel, in LNG form, will be economically either without or with adding the conversion cost. As shown; applying LNG fuel for main engines can achieve annual cost saving of 50 and 18 ( $/kW ) in case of LNG without and with adding conversion cost, respectively. Conversely, both SCR with MGO (of 0.1% sulfur content ) and SCR with sea water scrubber systems will cause increasing of the annual ship operating cost by about 35 and 45( $/kW ) , respectively.
CONCLUSION
Emissions from ships represent one of the important issues that concern those interested in maritime domain, as it has a negative impact on the marine environment. The present paper discussed the various methods which could carry out to reduce those emissions. Using of SCR and water scrubber systems as treatment technology onboard ships or natural gas as alternative fuel appeared as the best methods from the point view of environmental. Applying one of them depends on some criteria such as the required emission reduction percentage. Those methods were studied to be used for one of passenger ships working at the Red Sea. The results showed the possibility to achieve valuable emission reduction percentage by using of SCR and scrubber systems, but it will be costly and add more ship operating cost. On the other hand, using of LNG as alternative fuel will convince from the view point of environmental and economic issues.
ABBRIVIATION
PPT Slide
Lager Image
Acknowledgements
This work was funded by the Deanship of Scientific Research (DSR), King Abdulaziz University, Jeddah, under grant no. (980-118-D1435). The authors, therefore, acknowledge with thanks DSR technical and financial support.
References
Alexandros G. , George P. , Stylianos P. 2010 Application and cost–benefit analysis of solar hybrid power installation on merchant marine vessels Ocean Engineering Journal 37 (7) 592 - 602
Andreasen A. , Mayer S. 2007 Use of Seawater Scrubbing for SO2 Removal from Marine Engine Exhaust Gas Energy Fuels 21 (6) 3274 - 3279
Andersson K. , Winnes H. 2011 Environmental trade-offs in nitrogen oxide removal from ship engine exhausts Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment 225 (1) 33 - 42
Apostolos P. 2010 Holistic ship design optimization Journal of Computer -Aided design 42 (11) 1028 - 1044
Ariana I.M. , Nishida O. , Fujita H. 2006 Removal of marine diesel particulate matter by electrostatic precipitator Available at:
Banawan A.A. , Mosleh M. , Seddiek I.S. 2013 Prediction of the fuel saving and emissions reduction by decreasing speed of a catamaran Journal of Marine Engineering and Technology 12 (3) 40 - 48
Banawan A.A. , El-Gohary M.M. , Sadek I.S. 2010 Environmental and economical benefits of changing from marine diesel oil to natural-gas fuel for short-voyage high-power passenger ships Journal of Engineering for the Maritime Environment 224 (2) 103 - 113
Beecken J. , Mellqvist J. , Salo K. , Ekholm J. , Jalkanen J.P. 2014 Airborne emission measurements of SO2, Knox and particles from individual ships using sniffer technique Atmospheric Measurement Techniques 7 1957 - 1968
Bengtsson S. , Andersson K. , Fridell E. 2011 A comparative life cycle assessment of marine fuels liquefied natural gas Journal of Engineering for the Maritime Environment 225 (2) 97 - 110
Buhaug Ø. , Corbett J.J. , Endresen Ø. , Eyring V. , Faber J. , Hanayama S. , Lee D.S. 2009 Second IMO GHG study International Maritime Organization (IMO) London
2014 Bunker world prices Available at:
Christos C. , Oceane B. , Hans A.T. , Andreas B. 2014 Alternative fuels for shipping, DNV& GL. Position Paper 17-2014 Det Norske Veritas(DNV) Norway
Daniel A. , Jørgen T. , Robert E. , Frank S.L. , Svend B. , Ditte K. 2012 Investigation of appropriate control measures (abatement technologies) to reduce Black Carbon emissions from international shipping LITEHAUZ Denmark
Eide M.S.S.B. , Dalsøren Ø. , Endresen B. , Samset G. 2013 Reducing CO2 from shipping -do non - CO2 effects matter? Atmospheric Chemistry Physical 13 4183 - 4201
Elma K. , Bengtsson E.F. , Karin E.A. 2014 Fuels for short sea shipping: A comparative assessment with focus on environmental impact Journal of Engineering for the Maritime Environment 228 44 - 54
El-Gohary M.M. , Saddiek I. 2013 Utilization of alternative marine fuels for gas turbine power plant onboard ships International Journal of Naval Architecture and Ocean Engineering 5 (1) 21 - 32
Elgohary M.M. Energy Conservation: passenger and container ships case studies Alexandria Engineering Journal 48 (2) 151 - 159
El-Gohary M.M. 2012 The future of natural gas as a fuel in marine gas turbine for LNG carriers Journal of Engineering for the Maritime Environment 226 371 - 377
2009 Regulatory impact analysis: control of emissions of air pollution from category 3 marine diesel engines U.S. Environmental Protection Agency(EPA) USA
Eyring V. , Isaksen I.S.A. , Berntsen T. , Collins W. , Endresen O. , Grainger R. , Moldanova J. , Schlarger H. , Stevenson D. 2010 Transport impacts on atmosphere and climate: shipping Atmospheric Environment 44 (37) 4735 - 4771
Fotis D.K. , John M.P. , George J.T. 2014 Control system for fuel consumption minimization–gas emission limitation of full electric propulsion ship power systems Journal of Engineering for the Maritime Environment 228 17 - 28
Herdzik J. 2011 LNG as a marine fuel- possibilities and problems Journal of KOENS Powertrain and Transport 18 (2) 169 - 176
Fredrik H. 2008 A review on the use of gas and steam turbine combined cycles as prime movers for large ships Journal of Energy Conversion and Management 49 (12) 3458 - 3467
2003 Technical and other options for reducing marine vessel emissions in the Georgian basin. Technical report, March 26, 2003 Genesis Engineering Inc. Available at:
Gerasimos T. , George L. 2013 Techno-economical analysis of single pressure exhaust gas waste heat recovery systems in marine propulsion plants Journal of Engineering for the Maritime Environment 227 83 - 97
Gritsenko D. , Yliskyla¨-Peuralahti J. 2013 Governing shipping externalities: Baltic ports in the process of Sox emission reduction Journal of Maritime Studies 12 (10)
Hagh B.F. 2004 Comparison of autothermal reforming for hydrocarbon fuels Division of Fuel Chemistry 49 (1) 144 - 147
Hall W. 2010 Assessment of CO2 and priority pollutant reduction by installation shore-side power Resources, Conservation and Recycling 54 (7) 462 - 467
Harilaos N. , Christos A. , Nikolaos M. 2009 Speed reduction as an emissions reduction measure for fast ships 10th International Conference on Fast Sea Transportation FAST 2009 Athens, Greece, October 2009 1 - 12
Harsema A. 2013 LNG fuel tank container: a new approach to LNG bunkering Avaliable at:
Johansson L. , Jalkanen J.P. , Kalli J. , Kukkonen J. 2013 The evolution of shipping emissions and the costs of recent and forthcoming emission regulations in the northern European emission control area The Journal Atmospheric Chemistry and Physics Discuss 13 16113 - 16150
2008 Prevention of air pollution from ships. MEPC 57/21 28 - 57
2008 Prevention of air pollution from ships. MEPC 58/23 30 - 40
2009 Prevention of air pollution from ships. Second IMO GHG Study 2009. MEPC 59/4/7
Kjeld A. 2009 Exhaust gas emissions today and tomorrow 29th Motor ship Conference Denmark 26-27 May 2009 155 - 170
Lamas M.I. , Rodriguez C.G. 2012 Emissions from marine engines and NOx reduction Methods Journal of Maritime Research IX (1) 77 - 82
Lamas M.I. , Rodriguez J.D. , Telmo J. 2013 Internal modifications to reduce pollutant emissions from marine engines International Journal of Naval Architecture and Ocean Engineering 5 (4) 493 - 501
Lin B. , Lin C.Y. 2006 Compliance with international emission regulations: Reducing the air pollution from merchant vessels Marine Policy 30 (3) 220 - 225
Mekhilef S. , Saidur R. , Safari A. 2011 A review on solar energy use in industries Journal of Renewable and Sustainable Energy Reviews 15 (4) 1777 - 1790
Oihane C. , Basurko G.G. , Zigor U. 2012 Energy audits of fishing vessels: lessons learned and the way forward Second International Symposium on Fishing Vessel Energy Efficiency E-Fishing Vigo, Spain 22 - 24 May 2012 1 - 7
Kolwzan K. , Narewski M. , Statkow P.R. 2012 Study on alternative fuels for marine applications Clean Shipping Currents 1 (3) 1 - 43
Philippe C. 2009 Greenhouse gas emissions reduction potential from international shipping, paper No.2009-11 International Transport Forum Leipzig 27 May 2009
Radwan A. , Morsy M. , Elbadan A. 2007 Economical and environmental advantages of using NG as a fuel in inland water transport, paper No.14 In: 25th CIMAC conferenc Vienna 21-24 May 2007
Rosli A.B. 2008 Fuel injection pressure effect on performance of direct injection diesel engines based on experiment American Journal of Applied Sciences 5 (3) 197 - 202
Seddiek S.I. , Mosaad A.M. , Adel A.B. 2012 Thermo-economic approach for absorption air condition onboard highspeed crafts International Journal of Naval Architecture and Ocean Engineering 4 (4) 460 - 476
Seddiek S.I. , Mosaad A.M. , Adel A.B. 2013 Fuel saving and emissions cut through shore-side power concept for high-speed crafts at the red sea in Egypt Journal of Marine Science and Application 12 (4) 463 - 472
Stationary S.D. 2000 Risk reduction plan to reduce particulate emissions from diesel-fueled engines and vehicles, Technical report California Air Resources Board California
Shuaian W. , Qiang M. 2012 Sailing speed optimization for container ships in a liner shipping network Transportation Research Part E 48 (3) 701 - 714
TAYLAN M. 2010 An overview: effect of roughness and coatings on ship resistance, paper No.5 Internatonal Conference on Ship Drag Reduction Turkey 21 May 2010
Woodyard D. 2004 Pounder’s marine diesel engines and gas turbine 8th ed Butterworth-Heinemann Oxford
Welaya Y.M.A. , Gohary M.M.El. , Ammar N.R. 2011 A comparison between fuel cells and other alternatives for marine electric power generation International Journal of Naval Architecture and Ocean Engineering 3 (2) 141 - 149
Welaya Y.M.A. , Mosleh M. , Ammar N.R. 2013 Thermodynamic analysis of a combined gas turbine power plant with a solid oxide fuel cell for marine applications International Journal of Naval Architecture and Ocean Engineering 5 (4) 529 - 545
Winkler J. 2009 Efficient ship design can reduce CO2 now 29th Motor ship Conference Denmark 26-27 May 2009 75 - 105
Yang X. , Bai G. , Schmidhalter R. 2011 Shore to ship converter system for energy saving and emission reduction Power Electronics and ECCE Asia (ICPE & ECCE), IEEE 8th International Conference Jeju 30 May - 3 June 2011 2081 - 2086