Advanced
A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel
A study on an efficient prediction of welding deformation for T-joint laser welding of sandwich panel
-Part II : Proposal of a method to use shell element model-
International Journal of Naval Architecture and Ocean Engineering. 2014. Jun, 6(2): 245-256
Copyright © 2014, The Society of Naval Architects of Korea
This is an Open-Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Published : June 30, 2014
Download
PDF
e-PUB
PubReader
PPT
Export by style
Share
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Jae Woong Kim
Gas Technology R&D Group, Daewoo Shipbuilding & Marine Engineering Co., Ltd., Seoul, Korea
Beom Seon Jang
RIMSE, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, Korea
Sung Wook Kang
RIMSE, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, Korea
Abstract
I-core sandwich panel that has been used more widely is assembled using high power CO₂laser welding. Kim et al. (2013) proposed a circular cone type heat source model for the T-joint laser welding between face plate and core. It can cover the negative defocus which is commonly adopted in T-joint laser welding to provide deeper penetration. In part I, a volumetric heat source model is proposed and it is verified thorough a comparison of melting zone on the cross section with experiment results. The proposed model can be used for heat transfer analysis and thermal elastoplastic analysis to predict welding deformation that occurs during laser welding. In terms of computational time, since the thermal elasto-plastic analysis using 3D solid elements is quite time consuming, shell element model with multilayers have been employed instead. However, the conventional layered approach is not appropriate for the application of heat load at T-Joint. This paper, Part II, suggests a new method to arrange different number of layers for face plate and core in order to impose heat load only to the face plate .
Keywords
INTRODUCTION
The research of steel sandwich panels has been extensively carried out for the past decades. Among the sandwich panel, Icore panels offer high strength to weight and stiffness to weight ratios, making them favorable in transport industry, especially shipping. Moreover, these panels are proved to be more resistant to impact and blast loads and space efficiency is good to fill different systems such as piping and wiring ( Kujala et al., 2005 ; Yourlmaz et al., 2009 ). I-core sandwich panel is composed of two face sheet plates and web plates (called cores) welded perpendicular to the face sheet plates. CO 2 laser welding is adopted for T-joint welding between a core and a face plate due to its merits of narrow heat affected zone, small welding deformation, and deep penetration capability. CO 2 laser welding is known to induce less welding deformation than other conventional welding methods, however, the deformation level is still not ignorable in the sandwich panel since it consists of quite thin plates of 3-5 mm thickness. ( Kim et al., 2013 ). I-core sandwich panel is composed of two face sheet plates and web plates welded perpendicular to the face sheet plates as depicted in Fig. 1 .
PPT Slide
Lager Image
Shape of I-core sandwich panel.
Kim et al. (2013) proposed a simple volumetric heat source model of laser welding for I-core sandwich including the defocus phenomenon. For a verification of the proposed model, heat transfer analysis and thermal elasto-plastic analysis are performed to investigate heat distribution in the thickness direction and the resultant welding deformation, respectively.
Table 2 summarizes a few researches on welding deformation induced by laser welding. Moraitis and Labeas (2008) used 3D Gaussian model for a butt weld of DH36 steel plate and a lap joint of aluminum alloy. Heat transfer analysis and thermalelasto- plastic analysis was performed to simulate welding residual stress and deformation distortion using 3D solid element. An efficient keyhole model, which is independent of any empirical parameter, is introduced for the prediction of the keyhole size and shape required for the thermal analysis.
Tsirkas et al. (2003) simulated the laser welding process to predict laser welded panel distortions for butt joint specimen that consists of thick AH36 shipbuilding steel plates, using different welding parameters. Experimental testing was carried out to measure the distortion. Zain-ul-Abdeina et al. (2009) focused on the prediction of welding-induced distortions and residual stresses on thin sheets of 6056-T4 aluminum alloy. Cone-shaped volumetric heat source with Gaussian distribution and an upper hollow sphere is used to attain the required weld fusion zone size and temperature fields. From a comparative study of experimental and simulation results, a friction coefficient and a suction pressure to provide the best agreement in out-of-plane and in-plane displacements were found. Zain-ul-Abdeina et al. (2010) used a 3D volumetric conical heat source with Gaussian distribution without the hollow sphere for a fillet weld of T-joints made from 6056-T4 aluminum alloy. A comparative analysis of the experimental and simulation results showed a good agreement in temperature and displacement fields.
As an alternative to time-consuming thermal elasto-plastic analysis using 3D solid model, Sulaiman et al. (2011) developed a new linear elastic shrinkage method, named “Weld Planner”, to simulate welding deformation for GMAW process. Shell elements were used for the modeling of both plates and weld beads, which lead to more reduction in the computational time. It was employed to predict welding distortion induced in butt and T-joints of steel plates with thickness of 4 mm . The simulation results were compared with experiment results and the difference was identified within 20%.
The above mentioned researches treated a butt weld or a conventional filet weld. Thus, deep penetration is not needed and the consideration of defocus has not been taken into account. However, T-joint of sandwich panel requiring a laser shooting on face plate requires a deep penetration into the upper part of core. This is enabled by the defocus of laser shooting and it should be incorporated into the heat source model.
In addition, those researches treated simple plates and the computational time is not significant. However, a sandwich panel consists of many core plates and the correct prediction of welding deformation can be made by accumulating the welding deformation for all T-joints. In this regard, thermal elasto-plastic FE analysis using solid model is quite time consuming. Thus, shell element model with virtual layers are employed to reduce the computational time. The heat load can be distributed through thickness by generating virtual layers and applying power densities to virtual nodes in this study.
This study focuses on a practical purpose how to make use of shell element model aiming at reducing the computational time without a deterioration of accuracy in the analysis results. Even if it is not based on robust theoretical background, the idea proposed in this study is expected to be directly applied to the actual engineering work and offer a concrete benefit.
This paper is unfolded as follows. First, volumetric heat source model to be used in this research is briefly defined. A new approach, named “Hetero-layered approach (HLA)” is proposed along with a simple illustrating example and a study on the number of layer of face plate. It is followed by a verification work to compare the temperature distribution on the cross section and welding deformations among the proposed method, a conventional method to use 3D solid elements and experiment results. The computational time of the proposed method as well as the welding deformation is also compared with the conventional method through four comparative studies. Finally, a conclusion is laid.
Researches on a prediction of welding deformation and residual stress for laser welding.
PPT Slide
Lager Image
Researches on a prediction of welding deformation and residual stress for laser welding.
VOLUMETRIC HEAT SOUCE MODEL CONSIDERING DEFOCUS (Kim et al., 2013)
- Volumetric heat source model considering defocus
Kim et al. (2013) suggested a cone-shaped volumetric heat source model realizing the negative defocusing as shown in Fig. 2. It shows how to extend the proposed heat source model considering the negative defocus.
PPT Slide
Lager Image
Extension of the proposed heat source for negative defocus.
When defocus is zero, the heat source is assumed as a circular cone whose radius is R 0 , and depth is D 0 . When defocus (= D df ) is given, the radius of heat source (= R 1 ) is defined in the following formula.
PPT Slide
Lager Image
where,
  • R1: Radius of heat source for negative defocus
  • R0: Radius of heat source for zero defocus (= Radius of laser beam waist = 0.5mm)
  • Rfl: Radius of focusing lens (=15.5mm)
  • Lf: Focal length (=150mm)
Empirical formulas obtained from a series of experiments for the depth of heat source for zero defocus (= D 0 ) versus welding speed (= V weld ) were provided for power of 6.0kW ( D 0,6.0kW ) and 8.9 kW ( D 0,8.9kW ) on the assumption that the depth of molten zone would be the same as depth of keyhole and melting depth.
PPT Slide
Lager Image
From the above defined D 0 , the depth heat source for negative defocus ( D 1 ) can be simply calculated as the following formula.
PPT Slide
Lager Image
Laser heat energy multiplied by total welding efficiency (= η , 0.5) is uniformly distributed over the keyhole volume. This volumetric heat source distribution is assumed to be developed right after material inside keyhole changes into plasma condition. The power density ( Q ) can be defined as
PPT Slide
Lager Image
P is the power of welding and V is the volume of heat source. When defocus is 0 mm , V is
PPT Slide
Lager Image
when defocus is negative, V is
PPT Slide
Lager Image
where,
PPT Slide
Lager Image
HETERO-LAYERED APPROACH
For an assessment of welding deformation, 3D solid FE model has been employed for heat transfer analysis and thermal elatsto-plastic analysis in order to reflect heat load distribution across the thickness. However, even if a high performance computer is utilized, the assessment of welding deformation using 3D solid FE model is still quite time consuming. It is a big burden for prediction of welding deformation for a real scaled model.
For example, when thermal elasto-plastic analysis is performed for a 0.5 m × 0.5 m model using solid elements, the total number of elements is 15,000 and it takes 8 hours. In the case of shell element model, the number of element is 7,000 and the analysis time is remarkably reduced to one and half hours. Computational time of nonlinear FE analysis using solid elements surges as the model size increases. Thus, it is practically impossible to perform a thermal elasto-plastic analysis for a model of real size, for instance, 3 m × 9 m with 10 cores. This study employs shell element model and suggest a new method to apply heat source at the joint of face plate and core which leads to nearly the same heat distribution as that of solid elements.
- Suggestion of ‘HLA’ in shell element model
FE model of T-Joint with shell element has one node connection between face plate and web plate as shown in Fig. 3(a) . Some layers need to be defined in shell element in order to impose heat distribution in thickness direction. In Fig. 3(b) , the face plate and the core have four layers and three layers (including top and bottom layers) across thickness, respectively.
PPT Slide
Lager Image
T-joint modeling using shell elements with multi-layers.
This study proposes a method to define different number of layers for face plate from core and to distribute unevenly. Its purpose is to impose heat load only for the face plate at the joint. Fig. 4 depicts a shell model with seven layers for face plate and three layers for core including top and bottom surfaces. Between top (= T ) and bottom (= B ) layers, intermediate layers (= ILs ) and corresponding virtual nodes (= VNs ) can be defined. Heat load can be applied to the connection node along with a designated layer. If the top layer is designated, heat load is imposed on both a virtual node at top layer ( VN T ) of the face plate and that of the core. This causes unexpected welding deformation of core. On the other hand, if IL5 , IL4 , IL3 and IL2 are designated, the unintended application of heat load to core could be avoided since those intermediate layers don’t exist in the core.
PPT Slide
Lager Image
An example of hetero-layers approach.
The locations of layers need to be carefully set up. IL5 and IL2 are located quite closely to top and bottom layers, respectively. It is intended to impose heat loads of VN T and VN B to VN IL5 , and VN IL2 , respectively. Therefore, specific heat distribution can be achieved by assigning specific heat load values to evenly distributed virtual nodes ( V IL 2 , VN IL3 , VN IL4 , VN IL5 ) across the thickness. This approach is named HLA in this study.
The proposed HLA can be verified in a simple thermal elasto-plastic analysis as depicted in Fig. 5. The analysis model is a simple T-joint constructed with shell elements. The size of the model is 50 mm × 50 mm × 25 mm and thickness of plate and core is 3 mm . Fig. 5(b) is the resultant welding deformation when the same number of layers is used for the face plate and the core. That is the same heat load is applied to both the face plate and the core. This leads to incorrect welding deformation of core. The different temperature distribution at top and bottom layers causes bending of the core as well as the face plate.
PPT Slide
Lager Image
Verification of HLA in a simple thermal elasto-plastic analysis.
- Study on the number of layers of face plate
Intermediated layers of face plate can be classified into three as illustrated in Fig. 6.
PPT Slide
Lager Image
Definition of layers of face plate and core.
First, dummy layers corresponding to intermediate layers of core. These layers are not used and the number should be the same as the intermediate layers of core.
Second, two acting layers replacing top and bottom layers of face plate. These layers are introduced to replace exiting top and bottom layers of the face plate. Heat loads of the original top and bottom layers are imposed on these layers. One acting layer should be placed quite close to top layer and the other bottom layer.
Third, true intermediate layers. These layers are evenly distributed and the actual heat distribution across the thickness is realized by applying heat loads to virtual nodes at these layers. The sufficient number of layers should be created to accurately incorporate continuous variation through the thickness.
Therefore, the number of layers of face plate is determined as follows.
NILF = NILC + NAL + NTL
  • NILF: The number of intermediate layers of face plate
  • NILC: The number of intermediate layers of core
  • NAL: The number of two acting layers
  • NTL: The number of true layers of face plate
The number of true intermediate layers needs to be selected carefully since it can affect thermal elasto-plastic FE analysis, while the numbers of the other two layers are fixed and not affective to the result. A parametric study for different number of true intermediate layers is carried out to investigate its effect on the welding deformation.
Definitions of three case studies.
PPT Slide
Lager Image
Definitions of three case studies.
Here, the above-defined circular-cone type volume heat load is applied and other welding conditions are defined below.
  • - Laser power = 7.5kW
  • - Welding speed = 2m/min
  • - Defocus = 0mm
Fig. 7(a) is the analysis model and Fig. 7(b) shows the calculated welding deformation at point A, B and C and the difference of maximum deformation among three cases are found to be below 1%. From the results, five true layers can be seen sufficient to realize the heat distribution across the thickness and more layers is meaningless.
PPT Slide
Lager Image
Comparison of different numbers of intermediate layers (a) FE model (b) welding deformation plot.
VERIFICATION OF HETERO-LAYERED APPROACH
- Comparison of welding deformations
Heat transfer analysis using HLA in shell element model is carried out and the resultant heat distribution is compared with that with solid element model as shown in Fig. 8. Temperature distributions along four horizontal lines are compared and good agreements are identified.
There are two ways in checking the agreement of temperature distribution. One is to compare the difference of two maximum temperatures and the other is the maximum difference in two temperature distributions. The former is more generally used since the distribution of high temperature in transverse direction is the most influential to the welding deformation and the maximum temperature can be a representative value for the distribution.
PPT Slide
Lager Image
Comparison of temperature distribution between shell element and solid element.
To validate the proposed HLA, thermal elasto-plastic analysis is performed and welding deformation is compared with that from solid FE model and that from shell element model without the HLA. The proposed volumetric heat source model is used and other conditions. Fig. 9 compares vertical welding deflection from shell element model with and without HLA. Overall tendencies are nearly the same, but when HLA is not employed, the maximum vertical deflection becomes about 20% larger.
PPT Slide
Lager Image
Comparison of welding deflection obtained from thermal elasto-plastic analysis.
The welding deformations along four lines are compared together with solid element model and experiment result in Fig. 10 . ‘Shell with HL’ indicates a case of shell element model with HLA and ‘Shell w/o HL’ a case without the approach. It is identified that the result of shell element with HLA coincides well with the experimental result as well as solid element analysis results.
PPT Slide
Lager Image
Comparison of vertical welding deformations for a verification of HLA.
As listed in Table 3 the difference between shell model with HLA and the experiment is close to that of solid model. When HLA is not employed, unintended heat load causes a deformation of core and it affects to the deformation of face plate as well.
Comparison of max. deformations.
PPT Slide
Lager Image
Comparison of max. deformations.
- Comparison of computational time of shell model with HLA and solid model
In the previous section, the prediction of shell model with HLA shows a good coincidence with solid model. More cases are compared to validate the advantages of shell model in terms of computational time. Three cases are defined as follows and the FE models are summarized in Table 4 .
  • - Case I : single-sided model with one core
  • - Case II : single -sided model with four cores
  • - Case III : double-sided model with three cores
FE models of three case studies.
PPT Slide
Lager Image
FE models of three case studies.
In general, the number of elements used in solid model is much larger than that of shell model since the solid model uses a few elements across the thickness while the shell model defines virtual layers. Laser welding conditions are defined in Table 5. The above-defined volumetric heat sources are imposed on both actual nodes of 3D solid model and virtual nodes of shell model. The power with efficiency is divided by the number of nodes located inside the keyhole and the value is applied to the nodes.
Laser welding conditions of three cases.
PPT Slide
Lager Image
Laser welding conditions of three cases.
Fig. 11 shows the shape of vertical welding deformations in transverse direction of solid model and shell model and Table 6 summarizes maximum deformations at the edge of both sides. The difference between the solid model and shell model are below 5%. It can be regarded that analysis results with shell element have good agreement with analysis using solid element. On the other hand, the computational time of solid models are much longer than that of the corresponding shell models. The ratio of the computational times ranges from about 8.0 to 16.0. It is mainly due to the larger number of solid elements of solid model and the larger degree of freedom of solid element than those of shell element model.
PPT Slide
Lager Image
Comparison of welding deformations of solid model and shell models in three cases.
Results of case studies.
PPT Slide
Lager Image
Results of case studies.
CONCLUSION
Thermal elasto-plastic analysis using solid element model requires considerably long computational time due to its large number of elements and the inherent large degree of freedom of solid element. In this paper, a new method named HLA is suggested for the thermal elasto-plastic analysis for T-joint laser welding. It aims at the reduction of computation time by employing shell element model instead of solid element model. It enables to impose the same heat load at joint as solid element model by defining more intermediate layers at the face plate than the core. From, a heat transfer analysis, the resultant heat distribution on the cross section in the vicinity of the welding joint is observed to be nearly the same as that of solid element model. A thermal elasto-plastic analysis shows a good agreement of welding deformation between shell element model and solid element model.
With respect to computational time, three case studies are carried out. Thermal elasto-plastic analyses are carried out for both solid element model and shell element model and out-of-plane welding distortion and the computational time are compared. From the study, the proposed HLA can reduce the computational time by about 1/8 to 1/16 and the difference of maximum welding deformation remains below 5%. Conclusively, the application of HLA to thermal elasto-plastic analysis using shell elements is expected to cut down the computational time drastically while keeping the accuracy within tolerable level. This advantage may be more remarkable when predicting the welding deformation for real scaled sandwich panel.
The proposed method is expected to be applied to other welding methods to require deep penetration like electron beam welding for thick plate or laser welding at fillet joint. The target of the welding simulation can be also extended to other types of sandwich panels with different cores like corrugated cores, cup shaped cores, honeycomb cores, and so on. HLA is expected to enable an optimization the welding condition to enhance weldability while reducing welding deformation through a drastic reduction of computational time.
Acknowledgements
This work was supported by Daewoo Shipbuilding & Marine Engineering Co., Ltd. and Research Settlement Fund for the new faculty of SNU.
References
Kim J.W. , Jang B.S. , Kim Y.T. , Chun K.S. 2013 A study on an efficient prediction of welding deformation for T joint laser welding of sandwich panel, PART I : Proposal of a heat source model International Journal of Naval Architecture and Ocean Engineering 5 (3) 348 - 363
Kujala P. , Klanac A. 2005 Steel sandwich panels in marine applications Shipbuilding 56 305 - 314
Moraitis G.A. , Labeas G.N. 2008 Residual stress and distortion calculation of laser beam welding for aluminum lap joints Journal of Materials Processing Technology 198 260 - 269
Sulaiman M.S. , Sulaiman M.S. , Manurung Y.H.P. , Haruman E. , Rahim M.R.A. , Redza1 M.R. , Lidam R.N. , Abas S.K. , Tham G. , Chau C.Y. 2011 Simulation and experimental study on distortion of butt and T-joint using weld planner Journal of Mechanical Science and Technology 25 (10) 2641 - 2646
Tsirkas S.A. , Papanikos P. , Kermanidis T.H. 2003 Numerical simulation of the laser welding process in butt-joint specimens Journal of materials processing technology 134 (1) 59 - 69
Yourlmaz S. , Thompson L. , Caccese V. , Senthil S. 2009 Analysis and testing of a tapered end connection for laser welded steel sandwich panels One Liberty Center, The University of Marine Orono
Zain-ul-Abdeina M. , Nèliasa D. , Julliena J.F. 2009 Prediction of laser beam welding-induced distortions and residual stresses by numerical simulation for aeronautic application Journal of Materials Processing Technology 209 (6) 2907 - 2917
Zain-ul-Abdeina M. , Nèliasa D. , Julliena J.F. , Deloison D. 2010 Experimental investigation and finite element simulation of laser beam welding induced residual stresses and distortions in thin sheets of AA 6056-T4 Materials science and engineering A 527 (527) 3025 - 3039