Optimization for the direction of arrival estimation based on single acoustic pressure gradient vector sensor

International Journal of Naval Architecture and Ocean Engineering.
2014.
Mar,
6(1):
74-86

This is an Open-Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0) which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

- Published : March 31, 2014

Download

PDF

e-PUB

PubReader

PPT

Export by style

Share

Article

Metrics

Cited by

TagCloud

The optimization techniques are explored in the direction of arrival (DOA) estimation based on single acoustic pressure gradient vector sensor (APGVS). By analyzing the working principle and measurement errors of the APGVS, acoustic intensity approaches (AI) and the minimum variance distortionless response beamforming approach based on single APGVS (VMVDR) are deduced. The radius to wavelength ratio of the APGVS must be not bigger than 0.1 in the actual application, otherwise its DOA estimation performance will degrade significantly. To improve the robustness and estimation performance of the DOA estimation approaches based on single APGVS, two modified processing approaches based on single APGVS are presented. Simulation and lake trial results indicate that the performance of the modified approaches based on single APGVS are better than AI and VMVDR approaches based on single APGVS when the radius to wavelength ratio is not bigger than 0.1, and the two modified DOA estimation methods have excellent estimation performance when the radius to wavelength ratio is bigger than 0.1.
r
≤ 0.1
λ
, where
r
denotes the radius of the APGVS and
λ
denotes the wavelength corresponding to the highest working frequency of the APGVS) in real engineering application. As the working frequency increases, the approximation precondition is difficult to meet, and the DOA estimation performance will degrade. In this paper, we explore the optimized methods of the DOA estimation based on single APGVS to improve the DOA estimation performance even if the radius of APGVS does not meet the approximation precondition.
This paper is organized as follows: Section 1 is the introduction, section 2 and section 3 analyze the measurement model and measurement errors of the APGVS, respectively. Section 4 analyzes several DOA estimation methods based on single APGVS and presents two modified processing methods to increase the robustness of DOA estimation based single APGVS. To evaluate the performance of the modified DOA estimation methods, numerical simulation is conducted in section 5, and on-site trial and the associated data analysis in section 6. Finally, a conclusion is drawn in section 7.
Structure layout of the APGVS.
where
ω
_{0}
and
u
(
t
) are the radian frequency and the initial phase angle of the incident plane wave respectively,
k
denotes the wave number in water,
r
denotes the radius of the APGVS, and
α_{i}
(
i
=1,…,4) are the bearing angles of the four sensors referring to the X-axis.
Generally, the pressure of the APGVS is estimated by averaging the receiving signal of the four pressure sensors. Regardless of the system noise and ambient noise, the acoustic output pressure of the APGVS can be written as
when
kr
≪ 1, the pressure in the central point of the APGVS can be further denoted as
It can be observed from (3) that when
kr
≪ 1, the pressure in central point of the APGVS is equal to the average of received signals of the four pressure sensors.
The particle velocity components are usually obtained by finite difference of the pressure signal of these sensors on the same axis. Thus, the particle velocity components of the central point of the APGVS can be written as
where
e
^{− jπ/ 2}
is added to keep the same phase between the pressure and the particle velocity components. When
kr
≪ 1, the formulas (4) and (5) can be approximated as
Combining (3), (6) and (7), we can obtain a vector pattern as shown in (8) regardless of the normalization of amplitudes,
where
denotes the acoustic pressure wave in the central point of the APGVS.
where
r
denotes the radius of APGVS,
λ
is wavelength of the acoustic signal. From (9), we can find that the acoustic pressure measurement error is determined by incident angle and the radius to wavelength ratio (
Yang et al., 2013
).
Fig. 2
shows the curves of the acoustic pressure measurement error index with the radius to wavelength ratio for θ = 0°, 30°, and 45°, respectively. And the curves are obtained from (9). In real engineering application, the APGVS acoustic pressure measurement error index must meet the situation of |
ε_{p}
| ≤ 1d
B
. When
θ
∈[0,2
π
) and |
ε_{p}
| ≤ 1d
B
, the radius to wavelength ratio must meet the situation of
The acoustic pressure measurement error.
where
v
_{0x}
(
t
) and
v
_{0y}
(
t
) are the two components of the APGVS particle velocity at the central point. From (11) and (12), we can find that
and
are determined by incident angle
θ
and the radius to wavelength ratio
r
/
λ
. As the incident wave may come from arbitrary direction within[0,2
π
) , the two kinds of particle velocity measurement errors have the same variation in
θ
∈[0,2
π
) .
Fig. 3
shows the error index curves with the
r
/
λ
for θ = 0°, 30°, and 60°, respectively, which are obtained from (11). And when
θ
∈[0,2
π
) and |
ε_{p}
| ≤ 1d
B
, the radius to wavelength ratio must meet the situation of
Particle velocity measurement error.
In summary, if the acoustic pressure measurement error and particle velocity errors are not bigger than 1
dB
, the radius of the APGVS must meet
where
λ
is the wavelength corresponding to the highest working frequency of the APGVS. In the real engineering application, the condition denoted by (14) is usually called the approximation precondition of the APGVS. If the APGVS radius meets the approximation precondition, the APGVS has stable working performance and its particle velocity outputs have dipole directivity, otherwise, its DOA estimation performance declines significantly. When the APGVS is working in low frequency, it is easy to achieve the approximation precondition. Instead, if the APGVS works in relatively high frequency, it is difficult to achieve the approximation precondition, which makes a higher demand of fabricating materials and structure designs of the APGVS. At another point, the approximation precondition increases the cost of the APGVS and limits its application.
where
I _{x}
and
I _{y}
denote the average acoustic intensity of X-axis and Y-axis, respectively. Δ
_{x}
and Δ
_{y}
are the relative acoustic intensity components generated by noise. When the signal to noise ratio (SNR) is relatively high, the acoustic intensity components Δ
_{x}
and Δ
y
can be ignored. If we divide
I _{y}
by
I _{x}
and find its arctangent, we can get
where
is the azimuth estimation value of the incident wave.
The DOA estimation method aforementioned is usually referred to as “average acoustic intensity (AAI) method”. If there are multi-targets around the APGVS, the AAI method becomes ineffective, but we can utilize the difference of the incident signal spectra to distinguish them. We denote the Fourier transform of the three channels signals of the APGVS by
P
(
ω
),
V_{x}
(
ω
) and
V_{y}
(
ω
), thus, the cross spectra of acoustic pressure and particle velocity components can be written as
where the superscript * represents conjugate.
The ocean acoustic channel approximately meets the acoustic Ohm’s law, and acoustic pressure and particle velocity have the same phase. According to the properties of the Fourier transform, the azimuths of incident waves can be estimated by
where 〈⋅〉 represents moving average periodogram operator and Re{ } denotes the real value part of the entity inside{⋅} . The DOA estimation method denoted by (18) is usually referred to as “conjugate acoustic intensity (CAI) method”, which has better performance than AAI method in target detection, DOA estimation, multiple targets resolution, etc.
t
. And if
denotes the acoustic pressure autocorrelation function,
and
denote the cross-correlation function between the acoustic pressure and particle velocity on X-axis and Y-axis, respectively, from (2), (4) and (5), we can get
This can be put in more distinct form by simple deformation, and then we can get
Let
u
=
kr
cos
θ
and
v
=
kr
sin
θ
denote two unknowns, and solve the equations set (21), and then we can get
According to the relation of the trigonometric, the azimuth can be estimated by
To distinguish this approach from acoustic intensity method, it can be called “modified acoustic intensity (MAI) method”.
y
(
t
) of the APGVS with a vector operation, and make the output meet two criteria, one is the distortionless criterion and the other is minimum variance unbiased estimation criterion. According to convex optimization theory, the aforementioned process can be denoted as
where
P
is the output power of the APGVS,
w
is the weight factor, and
a
(
θ_{k}
) [ 1,cos
θ_{k}
, sin
θ_{k}
]
^{T}
is the steering vector of the incident wave.
is the covariance matrix estimation of the receiving data of the APGVS, which is denoted as
where
y
(
t_{n}
) denotes the
n
th snapshot of the APGVS, and
N
denotes the total snapshot number.
Solving equations set (24) by using a Lagrange multiplier, and the optimal weight factor
w _{opt}
can be obtained as
Substituting (26) into (24), we can obtain
where
a
(
θ
) [ 1,cos
θ
, sin
θ
]
^{T}
is the scanning vector of the APGVS, and
is its spatial spectra. We can calculate the
by varying
a
(
θ
) over
θ
∈[0,2
π
) and then choose its minima, thus the azimuth of incident wave is obtained. This process is called “MVDR beamforming method” of acoustic vector sensor (VMVDR).
where
is noise vector, and
is accurate steering vector of the APGVS, which can be written as
The accurate steering vector
is dependent on radius of the APGVS, so it has no approximation error with respect to radius variation of the APGVS. If we replace
in (29) with
a
(
θ
) in (27) , the spatial spectra of the APGVS can be written as
The steering vector is accurate, thus the output spatial spectra have no approximation errors. So the estimation performance of the estimator defined in (30) won’t degrade with increase of the radius of the APGVS. In order to distinguish the process defined in (30) from VMVDR, this processing approach is referred to as “modified MVDR beamforming method” of the APGVS (MVMVDR).
kHz
and pulse width 50
ms
, and the sampling frequency is 50
kHz
. The ambient noise is assumed to be isotropic noise and all the simulation results are obtained via 200 Monte-Carlo runs.
Fig. 4
shows the estimation performance of the four processing methods with the radius
r
= 0.02
m
of the APGVS. In this case, the radius to wavelength ratio is about 0.093, which is lower than 0.1, that is, the APGVS meets the approximation precondition. Subfigure (a) is the probability of success against the input SNR under the azimuth estimation limit is 1°, subfigure (b) is the bias of the DOA estimation against the input SNR and subfigure (c) is the standard deviation of DOA estimation against the input SNR. As
Fig. 4
shows, we can find
DOA estimation performance of the APGVS when r = 0.02m : (a) The probability of success of DOA estimation; (b) Bias of DOA estimation; (c) Standard deviation of DOA estimation
From
Fig. 4
, we can find that the two modified processing methods have better DOA estimation performance when the radius of the APGVS meets the approximation precondition denoted in (14).
Fig. 5
shows the estimation performance of the four processing methods with the radius
r
= 0.04
m
of the APGVS. In this case, the radius to wavelength ratio is about 0.187, which is bigger than 0.1, that is, the APGVS does not meet the approapproximation precondition. The physical implication of four subfigures is the same as that in
Fig. 4
. As
Fig. 5
shows, we can find
DOA estimation performance of the APGVS when r = 0.04m : (a) The probability of success of DOA estimation; (b) Bias of DOA estimation; (c) Standard deviation of DOA estimation
From
Fig. 5
, we can find that the two modified processing methods can still correctly estimate the target azimuth when the radius of APGVS does not meet approximation precondition. The MVMVDR method works better than the MAI method by about 20
dB
. The results indicate that the two modified processing approaches are feasible and effective compared to original approaches.
Fig. 6
studies the DOA estimation performance with different radiuses of four processing methods when the input SNR is 0
dB
. Three subfigure concepts are the same as in
Figs. 4
and
5
. Simulation results of
Fig. 6
show that the bias of DOA estimation of the four processing methods increases with the increase of the radius. The MAI method has better performance than the CAI, but its DOA estimation performance is worse than the MVMVDR method when the input SNR is small, which coincides with aforementioned results. With the highest probability of success, smallest bias and standard deviation, the MVMVDR method has the best DOA estimation performance in the four processing methods when the input SNR is relatively small.
DOA estimation performance of the APGVS with different radiuses: (a) The probability of success of DOA estimation; (b) Bias of DOA estimation; (c) Standard deviation of DOA estimation
m
was suspended from a ship to a depth of 3
m
and the sound speed about 1,450
m
/
s
. The source was dragged by a moving ship at the same depth as the receiving APGVS at the distance of about 80
m
, and the moving ship revolved around the receiving ship. The transmitted signal was a rectangular window modulated single frequency continuous-wave (CW) pulse with a frequency of
f
_{0}
= 7
kHz
, a duration of 2.86
ms
, and a repetition period of 1
s
. The sampling frequency of the time signal was
f
_{s}
= 50
kHz
.
Fig. 8
shows the received signal of the APGVS. The figure shows that the received signals are much stronger than the noise, that is, the signals to noise are fairly larger. In the lake trial, the radius to wavelength ratio was about 0.193, that is, the APGVS didn’t meet the approximation precondition expressed in (14).
Lake trial system of the APGVS.
Received pulse signals of the APGVS.
Fig. 9
shows the time-bearing display of the trial data by the CAI and the MAI methods. The ‘Accurate DOA’ in
Fig. 9
is the estimation of the DOA using the data of an APGVS array, which can be regarded as the practical azimuth of the incident wave. The results are given by three curves, the solid and dashdotted curve represent the DOA estimation of the CAI and MAI methods, respectively, and the dotted curve denotes the real azimuth. From the results of 80
s
data in
Fig. 9
, we can find the curve of the MAI method is closer from the real azimuth compared with the curve of the CAI method, which indicates that the MAI method is effective for high input SNR when the radius of APGVS does not meet the approximation precondition expressed in (14).
Time-bearing display of the CAI and the MAI methods.
Results of the VMVDR and MVMVDR methods are shown in
Fig. 10
and in
Fig. 11
, respectively. The two processing methods estimate the azimuth of incident wave by searching the maximum of the spatial spectra, thus the results are given in the form of time-bearing spectra surface. Comparing the results of the two processing methods in
Fig. 10
and in
Fig. 11
, we can find that the trace of the MVMVDR method is narrower and clearer than that of the VMVDR method. The trial results are quite similar to the simulation results described in the former section, which indicates that the MVMVDR method is effective when the radius of APGVS does not meet the approximation precondition expressed in (14).
Time-bearing display of the VMVDR method.
Time-bearing display of the MVMVDR method.
r
/
λ
≤0.1 under the condition that the amplitude errors of pressure and particle velocity are smaller than 1
dB
. The limit of radius to wavelength ratio is usually called “approximation precondition”. Two modified processing methods (the MAI and MVMVDR methods) are presented to improve the DOA estimation performance of the APGVS when it does not meet the approximation precondition. Finally, the simulation and lake trial are conducted to evaluate the performance of the two modified processing methods. From the results, we can conclude: (i) the two modified processing methods have better DOA estimation performance than original processing methods when the radius to wavelength ratio of the APGVS isn’t bigger than 0.1. (ii) The two modified processing methods can successfully estimate DOA of incident wave when the radius to wavelength ratio is bigger than 0.1. (iii) The two modified processing methods are unbiased when the signal to noise ratio is relatively high, and the MVMVDR method works better than the MAI method by about 20
dB
.

Acoustic pressure gradient vector sensor (APGVS)
;
Direction of arrival (DOA) estimation
;
Acoustic intensity
;
Minimum variance distortionless response (MVDR)

INTRODUCTION

The acoustic vector sensor (AVS), which measures the acoustic pressure and particle velocity simultaneously at a single point, has existed for over a century (
Jia, 2009
), recent advances in vector senor design have improved their utility in real engineering application (
Rouquette, 2007
;
Lockwood and Jones, 2006
;
Ma et al., 2011
). The AVS is advantageous for azimuth-elevation direction finding, because of the following two properties: (i) A single AVS intrinsically possesses a two-dimensional azimuth-elevation directivity; (ii) The steering vector of AVS is independent of the source’s frequency (
Wu et al., 2010
;
Tam and Wong, 2009
).
The ideal AVS and AVS array, which may be not affected by any unkown nonideality in the AVS’s amplitude response, phase response, collocation, or orthogonal orientation among its constituent velocity sensors, have been introduced and further studied by many researchers. The measurement model of the AVS array has been presented and the theoretical performance bounds on the direction finding based on AVS array has been analyzed (
Nehorai and Paldi, 1994
). Then, the direction finding algorithms that utilize the AVS’s unique array manifold have been developed, such as beamforming-based (
Hawkes and Nehorai, 1998
), MUSIC-based (
Wong and Zoltowski, 2000
), ESPRIT-based (
Xu et al., 2007
;
Wang et al., 2013
), and beamspace-based DOA estimation methods (
Chen and Zhao, 2004
).
Tam and Wong (2009)
and
Yuan (2012)
have studied how these various unknown nonidealities degrade direction finding accuracy via cramer-rao bound analysis. All above mathematical analysis and algorithms are based on the far-field measurement model, the near-field measurement model was investigated recently (
Wu et al., 2010
;
Jacobsen and Liu, 2005
). Zhou and Nehorai presented a novel approach for low frequency DOA estimation using miniature circular vector sensor array mounted on the perimeter of a cylinder (
Zhou and Nehorai, 2009
).
There are usually two types of acoustic vector sensors in the real engineering application, the resonant vector sensor which directly measures the particle velocity and the APGVS (
Nehorai and Paldi, 1994
). The APGVS is insensitive to mechanical disturbances and convenient to be installed, thus it has been used in sonarbuoy, submerged buoy and ultra-short baseline acoustic positioning systems (
Chen, 2007
;
Wan et al., 2006
). The APGVS must meet the approximation precondition (
MEASUREMENT MODEL OF APGVS

The two-dimensional APGVS is composed of four pressure sensors, whose structure can be demonstrated in
Fig. 1
. The acoustic pressure of the four sensors referring to the original point (the central point of the APGVS) can be denoted as
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

THE APGVS MEASUREMENT ERRORS

The APGVS did not measure acoustic pressure and particle velocity directly at a collocated point. The acoustic pressure was estimated by averaging the signals of the four pressure sensors, and the particle velocity components were estimated using pressure gradient of these sensors. Thus, the APVS has, to some degree, average and finite-difference approximation errors.
- Acoustic pressure measurement error

The acoustic pressure error can be evaluated by the ratio of estimated value to real value of the acoustic pressure. Frequently, we express the acoustic pressure error in dB and refer to it as “measurement error index” (
Yang et al., 2013
). Formulas (2) is the estimated value of the APGVS acoustic pressure, thus the measurement error index of the APGVS acoustic pressure will be
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

- Particle velocity measurement errors

The particle velocity measurement errors index is similar to that of the acoustic pressure. The (4) and (5) are finite-difference approximation values of the two components of the APGVS’s particle velocity at central point. Considering the compensation of amplitude of particle velocity, two kinds of measurement error indexes of the particle velocity can be written as
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

DOA ESTIMATION METHODS BASED ON SINGLE APGVS

- Acoustic intensity methods

Assuming the incident signal of targets and ambient noise received by the APGVS are uncorrelated, and from (8), the average acoustic intensity components can be written as
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

- Optimization for acoustic intensity methods

As the working frequency increases, it is increasingly difficult to meet the approximation precondition for the APGVS. To expand APGVS working frequency band and increase its application range, we must find new processing approaches to improve APGVS working performance (
Chen, 2007
).
For notational simplicity, we will omit explicit dependence on
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

- MVDR beamforming method

The minimum variance distortionless response (MVDR) beamforming of single APGVE is an extension of MVDR beamforming of array with multiple elements. We process the received signal
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

- Optimization for MVDR beamforming method

When the radius of APGVS does not meet the approximation precondition in (14), the estimation performance of VMVDR of APGVS will degrade significantly. The main reason is the approximation error of steering vector.
From (2), (4) and (5), the accurate output of the APGVS can be written as
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

SIMULATION AND RESULTS ANALYSIS

In this section, we present some experiments to evaluate the estimation performance of the aforementioned four processing methods. The incident wave is the CW pulse with central frequency 7
PPT Slide

Lager Image

- (1) Under the condition of 1° error limit, the probability of success reaches 100％ when the input SNR of CAI, MAI, VMVDR and MVMVDR methods is bigger than 10dB, −20dB, 2dB, −10dB, respectively. Thus the order is CAI>VMVDR> MVMVDR>MAI for input SNR threshold of four processing methods.
- (2) The DOA estimation bias of CAI and VMVDR methods is about 0.73° , and there is no bias for the MAI and the MVMVDR methods when their input SNR is bigger than 20dBand −8dB, respectively.
- (3) The standard deviation of the MAI and the MVMVDR methods are lower than the CAI and the VMVDR methods, respectively.

PPT Slide

Lager Image

- (1) Under the condition of 1° error limit, the probability of success of MAI and MVMVDR methods reaches 100％ when the input SNR meets SNR≥8dBand SNR≥−8dB, respectively. The CAI and VMVDR methods don’t correctly estimate the target azimuth under this condition.
- (2) MAI and MVMVDR methods are unbiased when the input SNR meets SNR≥−8dBand SNR≥20dB, respectively. The bias of the CAI and VMVDR methods increases to about 3.1°.
- (3) The standard deviation of the MVMVDR method is lower than that of the MAI method.
- (4) When the MAI and MVMVDR method reach unbiased estimation, their input SNR threshold is the same as inFig. 4, respectively.

PPT Slide

Lager Image

LAKE TRIAL AND DATA ANALYSIS

The proposed modified processing methods are applied to real underwater acoustic data collected by actual APGVS in lake water. The practical lake trial system was designed as shown in
Fig. 7
. The APGVS with radius 0.04
PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

PPT Slide

Lager Image

CONCLUSIONS

In this paper, the measurement model and the measurement errors of the APGVS are introduced, and several DOA estimation methods are analyzed. In real engineering application, the radius to wavelength ratio must meet 0≤
Acknowledgements

This research is funded by National Natural Science Foundation of China under Grant 60972152, Opening Research Foundation of State Key Laboratory of Underwater Information Processing and Control under Grant 9140C231002130C23085, and Project of Shandong Province Higher Educational Science and Technology Program under Grant J09lg08.

Chen B.B.
2007
Studies on DOA estimation of two-dimensional pressure-gradient vector transducer
Northwestern polytechnical university

Chen H.W.
,
Zhao J.W.
2004
Wideband MVDR beamforming for acoustic vector sensor linear array
IEE Proceedings-Radar Sonar and Navigation
151
(3)
158 -
162
** DOI : 10.1049/ip-rsn:20040651**

Hawkes M.
,
Nehorai A.
1998
Acoustic vector-senor beamforming and capon direction estimation
IEEE Transactions on Signal Processing
46
(9)
2291 -
2304
** DOI : 10.1109/78.709509**

Jacobsen F.
,
Liu Y.
2005
Near field acoustic holography with particle velocity transducers
Journal of the Acoustical Society of America
118
(5)
3139 -
3144
** DOI : 10.1121/1.2082687**

Jia Z.F.
2009
Novel sensor technology for comprehensive underwater acoustic information-vector hydrophones and their applications
Physics
38
(3)
157 -
168

Lockwood M.E.
,
Jones D.L.
2006
Beamformer performance with acoustic vector sensors in air
Journal of the Acoustical Society of America
119
(1)
608 -
619
** DOI : 10.1121/1.2139073**

Ma R.
,
Zhang W.T.
,
Li F.
2011
Two-axis slim fiber laser vector hydrophone
IEEE Photonics Technology Letters
23
(6)
335 -
337
** DOI : 10.1109/LPT.2011.2104413**

Nehorai A.
,
Paldi E.
1994
Acoustic vector-sensor array processing
IEEE Transactions on Signal Processing
42
(9)
2481 -
2491
** DOI : 10.1109/78.317869**

Rouquette R.E.
2007
Towed streamer deghosting

Tam P.K.
,
Wong K.T.
2009
Cramer-rao bounds for direction finding by an acoustic vector sensor under nonideal gainphase responses, noncollocation, or nonorthogonal orientation
IEEE Sensors Journal
9
(8)
969 -
982
** DOI : 10.1109/JSEN.2009.2025825**

Wan C.
,
Kong A.
,
Liu C.
2006
A comparative study of DOA estimation using vector/gradient sensors
Processings of IEEE Ocean Conference-Asia Pacific
Singapore
16-19 May 2006
1 -
4

Wang X.H.
,
Chen J.F.
,
Han J.
,
An Q.L.
2013
Performance analysis of DOA Estimation of vector hydrophone array based on ESPRIT algorithm
Systems Engineering and electronics
35
(3)
481 -
486

Wong K.T.
,
Zoltowski M.D.
2000
Self-initiating MUSIC-based direction finding in underwater acoustic particle velocity field beamspace
IEEE Journal of Oceanic Engineering
25
(2)
262 -
273
** DOI : 10.1109/48.838989**

Wu Y.I.
,
Wong K.T.S.
,
Lau K.
2010
The acoustic vector sensor’s near-field array-manifold
IEEE Transactions on Signal Processing
58
(7)
3946 -
3951
** DOI : 10.1109/TSP.2010.2047393**

Xu Y.
,
Liu Z.
,
Cao J.
2007
Perturbation analysis of conjugate MI-ESPRIT for single acoustic vector-sensor-based noncircular signal direction finding
Signal processing
87
(7)
1597 -
1612
** DOI : 10.1016/j.sigpro.2006.12.016**

Yang D.S.
,
Sun X.Y.
,
Hong L.J.
,
Zhou H. K.
2013
The velocity gradient sensor based on the vector hydrophone
Journal of Harbin Engineering University
34
(1)
7 -
14

Yuan X.
2012
Direction-finding with a misoriented acoustic vector sensor
IEEE Transactions on Aerospace and Electronic Systems
48
(2)
1819 -
1815

Zhou N.
,
Nehorai A.
2009
Circular acoustic vector sensor array for mode beamforming
IEEE Transactions on Signal Processing
57
(8)
3041 -
3052
** DOI : 10.1109/TSP.2009.2019174**

Citing 'Optimization for the direction of arrival estimation based on single acoustic pressure gradient vector sensor
'

@article{ E1JSE6_2014_v6n1_74}
,title={Optimization for the direction of arrival estimation based on single acoustic pressure gradient vector sensor}
,volume={1}
, url={http://dx.doi.org/10.2478/IJNAOE-2013-0164}, DOI={10.2478/IJNAOE-2013-0164}
, number= {1}
, journal={International Journal of Naval Architecture and Ocean Engineering}
, publisher={The Society of Naval Architects of Korea}
, author={Wang, Xu-hu
and
Chen, Jian-feng
and
Han, Jing
and
Jiao, Ya-meng}
, year={2014}
, month={Mar}