Optimization of the Processing Conditions for the Preparation of Surimi Products Containing Rice Flour

Fisheries and aquatic sciences.
2014.
Jun,
17(2):
167-173

This is an Open Access article distributed under the terms of the Creative Commons Attribution Non-Commercial Licens (http://creativecommons.org/licenses/by-nc/3.0/)which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.

- Received : August 14, 2013
- Accepted : September 30, 2013
- Published : June 30, 2014

Download

PDF

e-PUB

PubReader

PPT

Export by style

Share

Article

Metrics

Cited by

TagCloud

Surimi (or fish paste) products are one of the most representative processed seafoods in Korea. In a previous study, we evaluated the potential use of rice flour as an agent to replace wheat flour in surimi products. In this study, we optimized the content of rice flour and water in surimi products using response surface methodology. Rice flour content (
X
_{1}
, w/w) and water content (
X
_{2}
, v/w) were chosen as independent variables and gel strength (
Y
_{1}
) and overall acceptance (
Y
_{2}
) as dependent variables. Optimal conditions of
X
_{1}
and
X
_{2}
were 14% and 9.1%, respectively, and the predicted values of the multiple response optimal conditions were
Y
_{1}
= 656.4 (g∙cm) and
Y
_{2}
= 6.34. Under optimal conditions, the experimental values of
Y
_{1}
and
Y
_{2}
were 647.8 (g∙cm) and 6.21, respectively, which were similar to the predicted values. Surimi products that are prepared under optimum conditions were similar in gel strength to those of commercial products. However, its sensory evaluation score was higher than that of the commercial products. In conclusion, rice flour can not only be used as an alternative to wheat flour, but it also can be used to improve the quality of surimi products.
Lycii fructus
(Shin et al.,
2008
), and
Poria cocos
(Shin et al.,
2009
) have been reported. Currently, there exists few papers on the use of rice flour as a gel-enhancing ingredient in surimi products studied (Jung and Yoo,
2005
;Jung et al.,
2007
;Hur et al.,
2011
). However, the relationship between rice flour and surimi with regard to rheological properties and sensory evaluation has not been fully elucidated. In particular, no attempt has been made to optimize the content of rice flour in surimi products. In a previous study, we evaluated the effect of rice flour addition on the rheological and sensory properties of surimi products to check for the feasibility of using rice flour as an alternative to wheat flour for the production of premium surimi products (Cho et al.,
2013
). Therefore, the objective of the present study was to determine the optimum formulation of surimi products containing rice flour by using response surface methodology.
Nemipterus virgatus
) surimi (grade A; Khan Hoang Seaprex Co., Ltd., Soc Trang, Vietnam) was used in this study. (This surimi contained the usual cryoprotectants (e.g., sucrose, sorbitol, sodium polyphosphate, and sodium pyrophosphate)). Randomly selected surimi blocks (10 kg) were cut into 1 kg portions and kept at -20°C until further use. Rice flour (roll-mill, 80 mesh) was purchased from Daesun Flour Mills Co., Ltd. (Hampyeong, Korea). The other ingredients (Table
1
) were provided from Hansung Enterprise Co., Ltd. (Seongnam, Korea).

^{2}
factorial points, 4 axial points (α = 1.414) and 3 center points. Rice flour content (
X
_{1}
, %) and water content (
X
_{2}
, %) were chosen as the independent variables (IVs). The range and center point values of the two IVs were based on the results of preliminary experiments (Table
2
). Commonly, the minimum content of wheat flour was 5% in the commercial surimi products. In addition, when the rice flour added more than 15%, the prototype surimi products was not forming gel. Therefore, we chose the range of rice flour content from 5% to 15%. Gel strength (
Y
_{ 1 }
,g∙cm) and overall acceptance (
Y
_{2}
) were selected as the dependent variables (DVs) for the different combinations of IVs (Table
3
). To minimize the effects of unexpected variability in the observed responses, the experimental runs were randomized.
The example points of a central composite design (CCD) with two input parameters.

X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g․cm); Y _{2}, overall acceptance.
_{0}
is a constant, βi
,
βiiand βij are regression coefficients and Xi
,
Xj are the levels of the independent variables. The DVs,
Y
_{ 1 }
(gel strength) and
Y
_{ 2 }
(overall acceptance), were considered as parameters for optimization in order to prepare a sample with the highest gel strength and overall acceptance. The response surface plots were developed using Maple software version 7 (Waterloo Maple Inc., Ontario, Canada) and represented a function of two IVs.
P
< 0.05 for all analyses.
X
_{ 1 }
,
X
_{ 2 }
), quadratic (
X
_{ 1 }
X
_{ 1 }
,
X
_{ 2 }
X
_{ 2 }
) and interaction (
X
_{ 1 }
X
_{ 2 }
) were calculated for its significance using the
t
-test, and the estimated coefficients of each model are presented in Table
4
. In all models, the constant coefficients and linear terms were highly significant (
P
< 0.01). In contrast, the
X
_{ 1 }
X
_{ 1 }
term of quadratic coefficients and interaction coefficients of
Y
_{ 1 }
(gel strength) and
Y
_{ 2 }
(overall acceptance) were not significant. However, the
X
_{ 2 }
X
_{ 2 }
term of
Y
_{1}
(gel strength) and
Y
_{2}
(overall acceptance) were significant (
P
< 0.05). To develop the fitted response surface model equations, all insignificant terms (
P
> 0.05) were estimated and the corresponding fitted models are shown in Table
5
. Values of the determination coefficient (
R
^{2}
) for
Y
_{1}
and
Y
_{2}
were 0.946 and 0.965, respectively, and significant at the 99% probability level. The
R
^{ 2 }
values indicate that the model equations described the experimental designs adequately (Cho et al.,
2005
). This result confirmed that the experimental design based on the preliminary test was adequately performed.

X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g․cm); Y _{2}, overall acceptance.

X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g․cm); Y _{2}, overall acceptance.
Y
_{1}
(gel strength) and
Y
_{2}
(overall acceptance). The linear terms (
X
_{ 1 }
,
X
_{ 2 }
) for all the DVs were significant (
P
= 0.001 and
P
= 0.000, respectively) at the 99% probability level, whereas cross-product terms for all the DVs were not significant (
P
= 0.146 and
P
= 0.134, respectively) at the 95% probability level. The quadratic terms (
X
_{ 1 }
X
_{ 1 }
,
X
_{ 2 }
X
_{ 2 }
) of all the DVs were not significant (
P
= 0.062 and
P
= 0.077, respectively) at the 95% probability level. In the total regression model, all the DVs were significant (
P
< 0.01) at the 99% probability level. If the lack-of-fit test is not significant, then the model is fit (Isa et al.,
2011
). The results of the lack-of-fit test show that the
F
values of
Y
_{ 1 }
and
Y
_{2}
were 11.62 and 2.91, respectively, and the related
P
-values were not significant (0.080, and 0.266, respectively) at the 95% probability level. These results indicate the suitability of the models to accurately predict variation.

DF, degrees of freedom; SS, sum of square; MS, mean square. X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g․cm); Y _{2}, overall acceptance.
X
_{1}
increased from 5 % (-1.414) to 15 % (+1.414),
Y
_{1}
and
Y
_{2}
increased. However, when
X
_{2}
increased from 7 % (-1.414) to 14 % (+1.414),
Y
_{1}
and
Y
_{2}
were decreased. In a study by Chen et al. (Isa et al.,
1993
), starch addition up to 8% increased gel strength while lowering the expressible moisture value. This result is similar to our result where we show that the gel strength and moisture values have an inverse relationship. In addition, in a previous study, we suggested that an effective amount of rice flour to add was 10-15% (Cho et al.,
2013
). This result supported that rice flour content up to 15% increased gel strength and overall acceptance. As the coded values of IVs
X
_{1}
and
X
_{2}
were reached 13.5% (+1) and 9.25% (-0.5), respectively,
Y
_{1}
(gel strength) and
Y
_{2}
(overall acceptance) were increased. Generally, 4-12% of starch or wheat flour is added to surimi product (Park,
2005b
). However, up to 20-26% has been used for reducing the cost of surimi products (Hunt et al.,
2009
;Shim et al.,
2012
). Therefore, we suggest that rice flour can be more useful than wheat flour for reducing the costs of premium surimi products.
3D plot for preparation of surimi products containing rice flour for gel strength (A) and overall acceptance (B). X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g·cm); Y _{2}, overall acceptance.
Y
_{1}
, and
Y
_{2}
), which are shown in Table
7
. According to the canonical analysis of the response surface regression procedure, the eigenvalues of
Y
_{1}
was positive and the eigenvalue of
Y
_{2}
was negative. Therefore, the stationary points were target values. To obtain the optimal proportion of rice and water in surimi products, each target value,
Y
_{1}
(gel strength) and
Y
_{2}
(overall acceptance), were considered as a parameter during the optimization. The multiple optimal conditions (coded and actual values) of
X
_{1}
(rice flour content) and
X
_{2}
(water content) were 1.15 (14 %) and -0.55 (9.1 %), respectively. It has been reported that starch increases the gel strength of surimi products at lower concentration of 3% instead of higher concentrations of 6-10% (Yoon et al.,
1997
). In contrast, our results with rice flour show the opposite trend. It is considered that the gel strength was dependent on the inherent properties of starch and other ingredients used in the surimi product formulation (Hunt et al.,
2009
). The predicted values of
Y
_{1}
(gel strength),
Y
_{2}
(overall acceptance) at optimal conditions were 656.4 g∙cm and 6.34, respectively, and under optimal conditions, the experimental values were similar to the predicted values of
Y
_{1}
and
Y
_{2}
(647.8 g∙cm and 6.21, respectively). Therefore, the estimated response surface model was adapted for optimization of rice flour content in surimi products. Surimi products produced under optimum conditions were similar in strength to the gel strength of commercial products. However, its sensory evaluation score was higher than that of commercial products (Fig.
3
). In particular, typical fishy smell, which is a major cause of evasion of surimi product (Lee and Lee,
2002
), was reduced by adding rice flour. Therefore, rice flour enhances the quality of surimi products and is considered a valuable ingredient in the preparation of premium surimi products
.
Sensory evaluation of the prototype surimi products (PSP) and the commercial surimi product (CSP).

Superscript a and b represent significant differences ( P < 0.05). X _{1}, rice flour content (%, w/w); X _{2}, water content (%, v/w); Y _{1}, gel strength (g․cm); Y _{2}, overall acceptance.

Introduction

Surimi (or fish paste) products are the most representative processed fishery foods. They are widely used because their cooking is simple and inexpensive. In addition, surimi products can easily change the shape, taste, and texture of the final product as per consumer preferences (Kim et al.,
2005
). In South Korea, the most popular surimi product is the fried type, which is traditionally mixed with vegetables (Park,
2005a
;Choi et al.,
2012
). Currently, most surimi products are prepared using starch or wheat flour as an ingredient. Unfortunately, the price of wheat flour has increased and consumers were required high-quality products. Therefore, there is a need to come up with a cheaper alternative to replace wheat flour. Recently, rice flour was highlighted as a possible alternative to wheat flour (We et al.,
2011
).
Rice is the major staple crop of nearly half of the world’s population, and is particularly important in Asia, where approximately 90% of the world’s rice is produced and consumed (Zeigler and Barclay,
2008
;Khush,
2004
;Lee,
2012
). However, rice consumption in South Korea has decreased sharply owing to westernization of diet and increasing popularity of instant foods (Cha,
2010
;Statistics Korea,
2011
). Most rice are consumed after simple cooking and therefore the South Korean food industry is exploring the use of rice in new foods, both for domestic consumption and for export purposes (Shin,
2009
). The rheological properties and manufacturing process of surimi products containing different starches or functional powders, such as potato (Yang and Park,
1998
;Tabilo-Munizaga and Barbosa-Canovas,
2005
;Chung and Lee,
1996
), waxy corn (Alvarez et al.,
1997
), wheat (Kong et al.,
1999
), red ginseng (Shim et al.,
2012
),
Materials and Methods

- Materials

Golden threadfin bream (
Ingredients (g) of the preparation of surimi products containing rice flour

| | | | | |

100.0 | 1.5 | 2.3 | 2.0 | 6.7 | 0.3 |

- Preparation of the surimi product containing rice flour

Frozen surimi was partially thawed for 1 h at room temperature, to allow the core temperature to reach approximately -5°C. The thawed surimi was then cut into cubes (5 × 5 × 5 cm) and placed in a chopping bowl. The sample was chopped further at 1500 rpm for 5 min by a silent cutter (OMF-500, Ohmichi Co., Ltd., Maebashi, Japan). Two percent salt was added and the sample chopped for another 5 min at 1500 rpm. Rice flour was added slowly until homogenization of the mixture. The other ingredients were then added to the homogenized mixture according to the amounts listed in Table
1
and mixed for 3 min by the silent cutter. The formulation of Table
1
was selected because it is a general combination of ingredient for the production of commercial surimi products. During the chopping and mixing procedure, the temperature was maintained at approximately 5°C by crushed ice bath. After molding of the mixture, it was fried in soybean oil for 3 min at 150°C. All samples were then vacuum-packed and stored at 4°C.
- Determination of gel strength

Breaking force and deformation of the surimi product was measured by a puncture test using a TA-XT2 texture analyzer (Stable Micro Systems, Surrey, UK) equipped with a 0.25-inch spherical stainless probe. When the gel sample lost its strength and ruptured at a crosshead speed of 1.0 mm/s, the breaking force and depth of depression were recorded. Ten cylindrical samples with a length of 2.5 cm were subjected to the test. Gel strength was calculated using the following formula:
$${\mathrm{Gel}}\hspace{0.33em}{\mathrm{strength}}\hspace{0.33em}{\mathrm{(}}{\mathrm{g}}{\mathrm{.}}{\mathrm{cm}}{\mathrm{)}}\mathrm{{=}}{\mathrm{breaking}}\hspace{0.33em}{\mathrm{force}}{\mathrm{(}}{\mathrm{g}}{\mathrm{)}}\mathrm{\times}{\mathrm{depth}}\hspace{0.33em}{\mathrm{of}}\hspace{0.33em}{\mathrm{depression}}{\mathrm{(}}{\mathrm{cm}}{\mathrm{).}}$$

- Sensory evaluation

A trained panel comprising 20 members of the Korea Food Research Institute determined the organoleptic characteristics of the sample. The outward appearance, color, flavor, taste, chewiness, hardness, and overall acceptance were evaluated by a 7-point Likert scale (1 = extremely dissatisfied, 7 = extremely satisfied).
- Experimental design

Central composite design (CCD) (Box and Wilson,
1951
) was adopted in the optimization of rice flour and water content proportions in surimi products (Fig.
1
). CCD matrix consists of 2
PPT Slide

Lager Image

Experimental range and values of the independent variables in the central composite design for preparation of surimi products containing rice flour

| | | |||||

| | | | | |||

Rice flour content | _{1} | 5 | 6.5 | 10 | 13.5 | 15 | |

Water content | _{2} | 7 | 8 | 10.5 | 13 | 14 |

Central composite design and responses of the dependent variables for preparation of the surimi products containing rice flour

| | | |||||||||

| | _{1} | _{2} | ||||||||

_{1} | _{2} | _{1} | _{2} | ||||||||

Factorial portion | 1 | -1 | -1 | 6.5 | 8.0 | 559 | 5.5 | ||||

2 | +1 | -1 | 13.5 | 8.0 | 642 | 6.4 | |||||

3 | -1 | +1 | 6.5 | 13.0 | 395 | 3.9 | |||||

4 | +1 | +1 | 13.5 | 13.0 | 582 | 5.6 | |||||

Star portion | 5 | -1.414 | 0 | 5.0 | 10.5 | 513 | 4.8 | ||||

6 | +1.414 | 0 | 15.0 | 10.5 | 630 | 6.0 | |||||

7 | 0 | -1.414 | 10.0 | 7.0 | 657 | 6.3 | |||||

8 | 0 | +1.414 | 10.0 | 14.0 | 390 | 4.0 | |||||

Center portion | 9 | 0 | 0 | 10.0 | 10.5 | 590 | 5.6 | ||||

10 | 0 | 0 | 10.0 | 10.5 | 611 | 5.7 | |||||

11 | 0 | 0 | 10.0 | 10.5 | 607 | 5.9 |

- Analysis of data and optimization

For the response surface regression procedure, MINITAB software version 14 (Minitab Inc., Harrisburg, PA, USA) was used to fit the following quadratic polynomial equation:
$${\rm Y}=\beta_{0}+\sum\limits_{{\rm i}=1}^{{\rm P}}{\beta{\rm i}}{\rm Xi}+\sum\limits_{{\rm i}=1}^{{\rm P}}{\beta{\rm ii}}{\rm Xi}^{2}+\sum\limits_{{\rm ij}=2}^{{\rm P}}{\>\beta{\rm ij}}{\rm XiXj}$$

where Y is the dependent variable (gel strength and overall acceptance), β
- Statistical analysis

Statistical analyses of data were performed using SPSS software Version 13 (SPSS Inc., Chicago, IL, USA). Results were presented as average and standard deviations. Tukey’s multiple range test was carried out with one-way analysis of variance (ANOVA) to determine the significance of the differences in the mean among treatments. The significance level was set at
Results and Discussion

- Diagnostic checking of the fitted models

Response surface methodology (RSM) is a useful statistical technique that has been applied to optimize formulations in various food products (Murphy et al.,
2004
). This methodology reduces the number of experimental runs required to generate sufficient information in order to provide a statistically acceptable result (Fogaça et al.,
2013
). The response surface regression procedure was employed to fit the quadratic polynomial equation to the experimental data. All the coefficients of linear (
Estimated coefficients of the fitted quadratic polynomial equation for responses based ont-statistic for preparation of surimi products containing rice flour

| _{1} | _{2} | ||||

| | | | |||

Constant | 602.67 | 0.001 | 5.7333 | 0.001 | ||

_{1} | 54.43 | 0.004 | 0.5371 | 0.001 | ||

_{2} | -75.20 | 0.001 | -0.7066 | 0.001 | ||

_{1} _{1} | -16.33 | 0.256 | -0.1479 | 0.177 | ||

_{2} _{2} | -40.33 | 0.025 | -0.2729 | 0.034 | ||

_{1} _{2} | 26.00 | 0.146 | 0.2000 | 0.134 |

Response surface model for preparation of surimi products containing rice flour

| ^{2} | | |

_{1}= 602.67 + 54.43 _{1}- 75.20 _{2}- 16.33 _{1} ^{2}- | 0.946 | 0.003 | |

_{2}= 5.7333 + 0.5371 _{1}- 0.7066 _{2}- 0.1479 _{1} ^{2}- | 0.965 | 0.001 |

- Analysis of variance (ANOVA)

The statistical significance of the quadratic polynomial model equation was evaluated by analysis of variance (ANOVA). Table
6
shows ANOVA results for the models that explain the response of the two dependent variables,
Analysis of variance (ANOVA) for response of dependent variables (Y1andY2)

| | | | | | | ||

_{ 1 } | Regression | Linear | 2 | 68943.1 | 34471.5 | 37.62 | 0.001 | |

Quadratic | 2 | 9310.1 | 4655.0 | 5.08 | 0.062 | |||

Cross-product | 1 | 2704.0 | 2704.0 | 2.95 | 0.146 | |||

Total model | 5 | 80957.1 | 16191.4 | 17.67 | 0.003 | |||

Residual | Lack of fit | 3 | 4332.9 | 1444.3 | 11.62 | 0.080 | ||

Pure error | 2 | 248.7 | 124.3 | |||||

Total error | 5 | 4581.6 | 916.3 | |||||

Total | 10 | 85538.7 | ||||||

_{ 2 } | Regression | Linear | 2 | 6.30220 | 3.15110 | 62.84 | 0.000 | |

Quadratic | 2 | 0.44890 | 0.22445 | 4.48 | 0.077 | |||

Cross-product | 1 | 0.16000 | 0.16000 | 3.19 | 0.134 | |||

Total model | 5 | 6.91110 | 1.38222 | 27.57 | 0.001 | |||

Residual | Lack of fit | 3 | 0.20405 | 0.06802 | 2.91 | 0.266 | ||

Pure error | 2 | 0.04667 | 0.02333 | |||||

Total error | 5 | 0.25072 | 0.05014 | |||||

Total | 10 | 7.16182 |

- Response surface plots and the effect of factors

The estimated response function and the effect of the IVs on the DVs are shown in Fig.
2
. When
PPT Slide

Lager Image

- Optimization of multiple responses and comparison of quality characteristics with commercial products

Optimal conditions included both coded and uncoded values of the dependent variables (
PPT Slide

Lager Image

Multiple response optimization for the preparation of surimi products containing rice flour of predicted and experimental values

| _{ 1 } | _{ 2 } | ||||

Optimal conditions | _{ 1 } | Target value | > 650 | |||

Coded value | 1.15 | |||||

Actual value | 14.0 (%) | |||||

_{ 2 } | Target value | > 6.0 | ||||

Coded value | -0.55 | |||||

Actual value | 9.1 (%) | |||||

Predicted value | 656.4 | 6.34 | ||||

Experimental value | 647.8 ± 13.4 ^{a} | 6.21 ± 0.66 ^{a} | ||||

Commercial product | 617.8 ± 20.7 ^{a} | 3.40 ± 0.55 ^{b} |

Acknowledgements

This study was supported by grants from the Korea Food Research Institute (E0114400).

Alvarez C
,
Couso I
,
Solas M
,
Tejada M
1997
Waxy corn starch affecting texture and ultrastructure of sardine surimi gels
Eur Food Res Technol
204
121 -
128
** DOI : 10.1007/s002170050048**

Box GEP
,
Wilson KB
1951
On the experimental attainment of optimum conditions
J R Stat Soc Ser B
13
1 -
45

Cha HM
2010
A study on the trend analysis regarding the rice consumption of Korean. M.S. Thesis
Woosong University
Daejeon, KR

Chen JS
,
Lee CM
,
Crapo C
1993
Linear programming and response surface methodology to optimize surimi gel texture
J Food Sci
58
535 -
536
** DOI : 10.1111/j.1365-2621.1993.tb04318.x**

Cho S
,
Yoon M
,
Kim SB
2013
Effects of rice flour milling types and addition methods of rheological and sensory properties of surimi products
Kor J Fish Aquat Sci
46
139 -
146

Cho SM
,
Gu YS
,
Kim SB
2005
Extracting optimization and physical properties of yellow fin tuna (Thunnus albacares) skin gelatin compared to mammalian gelatins
Food Hydrocol
19
221 -
229
** DOI : 10.1016/j.foodhyd.2004.05.005**

Choi SY
,
Choi EY
,
Lee KE
,
Song AS
,
Park SH
,
Lee SC
2012
Preparation and quality analysis of fish paste containingStyela clavatunic
J Kor Soc Food Sci Nutr
41
1591 -
1595

Chung KH
,
Lee CM
1996
Evaluation of wheat gluten and modified starches for their texture-modifying and freeze-thaw stabilizing effects on surimi based-products
J Food Sci Nutr
1
190 -
195

Fogaça FHS
,
Trinca LA
,
Bombo ÁJ
,
Sant’Ana LS
2013
Optimization of the surimi production from mechanically recovered fish meat (MRFM) using response surface methodology
J Food Qual
36
209 -
216
** DOI : 10.1111/jfq.12019**

Hunt A
,
Getty KJK
,
Park JW
2009
Roles of starch in surimi seafood: a review
Food Rev Int
25
299 -
312
** DOI : 10.1080/87559120903155834**

Hur SI
,
Cho S
,
Kum JS
,
Park JW
,
Kim DS
2011
Rice flour-A functional ingredient for premium crabstick
Food Sci Biotechnol
20
1639 -
1647
** DOI : 10.1007/s10068-011-0226-z**

Isa KM
,
Daud S
,
Hamidin N
,
Ismail K
,
Saad SA
,
Kasim FH
2011
Thermogravimetric analysis and the optimisation of bio-oil yield from fixed-bed pyrolysis of rice husk using response surface methodology (RSM)
Ind Crops Prod
33
481 -
487
** DOI : 10.1016/j.indcrop.2010.10.024**

Jung YH
,
Yoo B
2005
Thermal gelation characteristics of composite surimi sol as affected by rice starch
Food Sci Biotechnol
14
871 -
874

Jung YH
,
Kim WW
,
Yoo B
2007
Effect of acetylated rice starch on rheological properties of surimi sol and gel
Food Sci Biotechnol
16
817 -
821

Khush GS
2004
Harnessing science and technology for sustainable rice-based production systems
Int Rice Comm News Lett
53
17 -
23

Kim HS
,
Choi SG
,
Park CH
,
Han BW
,
Yang SK
,
Kang KT
,
Oh HS
,
Heu MS
,
Kim JS
2005
Preperation and characteristics of surimi gel with red-tanner crab (Chionoecetes japonicus) paste
J Kor Soc Food Sci Nutr
34
1103 -
1108

Kong DS
,
Ogawa H
,
Iso N
1999
Compression properties of fish-meat gel as affected by gelatinization of added starch
J Food Sci
64
283 -
286
** DOI : 10.1111/j.1365-2621.1999.tb15883.x**

Lee K
,
Lee Y
2002
Attitude and behavior of seafood consumption among Korean housewives
Kor J Food Culture
17
111 -
119

Lee NY
2012
Starch and pasting characteristics of various rice flour collected from markets
Kor J Food Preserv
19
257 -
262

Murphy SC
,
Gilroy D
,
Kerry JF
,
Buckley DJ
,
Kerry JP
2004
Evaluation of surimi, fat and water content in a low/no added pork sausage formulation using response surface methodology
Meat Sci
66
689 -
701
** DOI : 10.1016/j.meatsci.2003.07.001**

Park JW
,
Park JW
2005a
Surimi seafood: products, market, and manufacturing. In: Surimi and Surimi Seafood
CRC Press
Boca Raton, FL, US
375 -
434

Park JW
,
Park JW
2005b
Ingredient technology for surimi and surimi seafood. In: Surimi and Surimi Seafood
CRC Press
Boca Raton, FL, US
649 -
707

Shim DW
,
Jiang J
,
Kim JH
,
Kim WW
,
Kang WS
,
Choi WS
,
Hur SJ
,
Kim DY
,
Kim KC
,
Lee KH
2012
Effects of size adjusted with red ginseng powders on quality of fish pastes
J Kor Soc Food Sci Nutr
41
1448 -
1453

Shin M
2009
Rice-processed food
Food Science and Industry
42
2 -
18

Shin YJ
,
Kim KS
,
Park GS
2009
Texture and sensory characteristics of fish paste containing whitePoria cocoswolf power
Kor J Food Cookery Sci
25
119 -
125

Shin YJ
,
Lee JA
,
Park GS
2008
Quality characteristics of fish pastes containingLycii fructuspowder
J East Asian Soc Dietary Life
18
22 -
28

Statistics Korea
2011
Household food grain consumption per capita in 2010 [Internet]
Statistics Korea
Deajeon, KR, Accessed 25 Jul2013

Tabilo-Munizaga G
,
Barbosa-Canovas GV
2005
Pressurized and heat treated surimi gels as affected by potato starch and egg white: microstructure and water-holding capacity
LWT-Food Sci Technol
38
47 -
57
** DOI : 10.1016/j.lwt.2004.04.013**

We GJ
,
Lee I
,
Kang TY
,
Min JH
,
Kang WS
,
Ko S
2011
Physicochemical properties of extruded rice flours and a wheat flour substitute for cookie application
Food Eng Prog
15
404 -
412

Yang H
,
Park JW
1998
Effects of starch properties and thermal-processing conditions on surimi-starch gels
LWT-Food Sci Technol
31
344 -
353
** DOI : 10.1006/fstl.1997.0366**

Yoon WB
,
Park JW
,
Kim BY
1997
Linear programming in blending various components of surimi seafood
J Food Sci
62
561 -
564
** DOI : 10.1111/j.1365-2621.1997.tb04430.x**

Zeigler RS
,
Barclay A
2008
The relevance of rice
Rice
1
3 -
10
** DOI : 10.1007/s12284-008-9001-z**

Citing 'Optimization of the Processing Conditions for the Preparation of Surimi Products Containing Rice Flour
'

@article{ E1HKAL_2014_v17n2_167}
,title={Optimization of the Processing Conditions for the Preparation of Surimi Products Containing Rice Flour}
,volume={2}
, url={http://dx.doi.org/10.5657/FAS.2014.0167}, DOI={10.5657/FAS.2014.0167}
, number= {2}
, journal={Fisheries and aquatic sciences}
, publisher={The Korean Society of Fisheries and Aquatic Science}
, author={Yoon, Minseok
and
Kim, Jin-Soo
and
Kim, Dongsoo
and
Jo, Jinho
and
Cho, Suengmok}
, year={2014}
, month={Jun}