Effect of Temperature-increase Rate and Terminal Temperature on the Solubilization of Sewage Sludge using Microwave Irradiation
Effect of Temperature-increase Rate and Terminal Temperature on the Solubilization of Sewage Sludge using Microwave Irradiation
Environmental Engineering Research. 2009. Mar, 14(1): 48-52
Copyright ©2009, Korean Society of Environmental Engineering
  • Received : November 11, 2008
  • Published : March 31, 2009
Export by style
Cited by
About the Authors
Woon-Ji Park
Johng-Hwa Ahn
Chan-Ki Lee
Solubilization of sewage sludge creates favorable conditions for anaerobic microorganisms to produce biogas. In this paper, we quantify the effect of heating pretreatment on the degree of solubilization of sewage sludge. The pretreatment process was carried out using a lab-scale industrial microwave unit (2450 MHz frequency). Response surface analysis was applied to determine the combination of temperature-increase rate (ramp rate) (2.9 to 17.1 ℃/min) and terminal temperature (52 to 108℃). Both ramp rate and temperature significantly affected the solubilization degree of sludge. Within the design boundaries, the conditions predicted to maximize the solubilization degree of 15.8% were determined to be 2.9 ℃/min and 104℃.
1. Introduction
The processing and disposal of sewage sludge is one of the most important and complex problems in the operation of municipal wastewater treatment plants. 1) Anaerobic digestion has long been used to treat sludge generated by the treatment of municipal and industrial wastewater. The main fraction of sludge consists of bacterial materials that commonly withstand direct anaerobic degradation because the cell walls from physical and chemical barriers to exoenzyme degradation and hydrolysis. Thus, the availability of intracellular organic material from feed cells is restricted, and long retention times of 20-30 days are required to reach moderate efficiencies of 30 - 50% in typical anaerobic digestion .2,3)
Anaerobic degradation of particulate materials and macromolecules is considered to occur in four steps: hydrolysis, acidogenesis, acetogenesis, and methanogenesis. In sludge digestion, hydrolysis is the rate-limiting step. 4) To use particulates as a substrate, bacteria release extracellular enzymes that break down and solubilize organic particulate matter. 5) To improve digestion efficiency, the most logical approach is to disrupt the microbial cells in the sludge. The disintegration of sludge has therefore been introduced to solubilize and convert slowly biodegradable, particulate organic materials to readily biodegradable low-molecular- weight compounds. 6)
Disintegration of sludge may be performed mechanically, ultrasonically, chemically, or thermally. Mechanical pretreatment has been shown to be highly effective in solubilizing microbial cells, although the process is complicated and expensive. 1) Sonication is effective in disintegrating 70-100% of sludge cells, but this approach is energy-intensive. Chemical and thermochemical pretreatments, based on strong acidic or basic conditions in combination with high temperatures and pressures, are efficient in enhancing sludge digestion, 7) but the aggressive reaction conditions commonly require the use of specialized materials. The high costs of wet sludge disintegration, in addition to corrosion problems and limited knowledge of the process itself, prevent this approach from achieving its potential as an anaerobic process 1) ; consequently, an effective and economical pretreatment is essential.
Microwaves are used in many and varied applications, including organic decomposition, sterilization of medical waste, and inactivation of microorganisms in foods, animal manure, and soil. 8) The advantages of microwaves in these applications include rapid heating, pathogen destruction, ease of control, compactness, and low overall cost. 9) Destruction of microorganisms is generally thought to occur due to the thermal effects of microwave exposure, although several researchers have investigated whether such irradiation also has a non-thermal effect. 10) The application of microwave fields can cause polarized side-chains of macromolecules to align with the direction of the electric field, leading to the possible breakage of hydrogen bonds and alteration of the hydration zone. 8) The principal factors of microwave radiation that affect dielectric materials include temperature, radiation time, output power, and penetration depth. 8)
When multiple factors and interactions affect a response of interest, response surface analysis (RSA) is an effective tool for optimizing the process. RSA is a collection of mathematical and statistical techniques for building empirical models. 11) The main advantage of RSA is the reduced number of experimental trials needed to evaluate parameters and their interactions. Therefore, it is less laborious and time-consuming than other approaches required to optimize a process. 12)
Currently, information is lacking concerning the effects of pretreating sludge with microwaves. Therefore, the objective of this study is to investigate the effects of microwave irradiation on solubilization of sewage sludge.
2. Materials and Methods
- 2.1. Sewage Sludge
Primary and secondary sludges (Table 1) were obtained from a municipal wastewater treatment plant in Chuncheon, Korea. The ratio of volatile solid (VS) to total solid (TS) in the sludges, 62-67%, indicated that the sludges consisted mainly of organic substances. Most of the chemical oxygen demand (COD) was associated with the solid phase rather than soluble phase, as evidenced by the low soluble COD (SCOD) to total COD (TCOD) ratio of 2.3-2.8% (Table 1) .
In a preliminary trial (data not shown) the solubilization degree was increased as the ratio of primary sludge to secondary sludge increased (p < 0.05). However, the primary and secondary sludges were produced in all wastewater treatment plants at the same time and can be treated in an anaerobic digester. Therefore, the sludges were blended (50:50 v/v) to analyze the effects of microwave pretreatment on solubilization without considering the ratio of both sludge production (Table 1) .
- 2.2. Microwave Irradiation
To study the microwave effects on sewage sludge we used a Microwave Accelerated Reaction System (MARS, CEM Corporation, 0-1600 W power output, 2450 MHz frequency, 102 atm maximum pressure, temperature range: 0-330℃) equipped with temperature and pressure sensors within the cavity and a turntable with pressure-sealed vessels (Omni) of 100 mL each (Fig. 1) . Samples (70 mL) of sewage sludge were pretreated in a vessel rotating on the turntable. After target temperatures (52℃ to 108℃) were reached, samples were removed from the heating source, allowed to cool to room temperature and then stored at 4°C in a refrigerator.
- 2.3. Analysis of Sewage Sludge Solubilization
In a preliminary trial (data not shown) that analyzed the effects of terminal temperature, temperature-increase rate (ramp rate), holding time, and output power on sludge solubilization, the holding time did not have a significant effect ( p > 0.05). Output power and irradiation time were related to ramp rate and target temperature affected sludge solubilization significantly ( p < 0.001). Therefore, temperature and ramp rate were selected as independent variables in the analysis of sludge-solubilization
Characteristics of sewage sludge
PPT Slide
Lager Image
Characteristics of sewage sludge
PPT Slide
Lager Image
Microwave accelerated reaction system and pressure sealed vessels used for pretreatment.
Experimental conditions and results of the central composite design
PPT Slide
Lager Image
Experimental conditions and results of the central composite design
rates by microwave irradiation.
RSA was used to determine the relationship of the sludge solubilization to ramp rate and temperature. It was applied to evaluate the relative significance of the environmental factors and to determine the conditions under which solubilization of sludge is maximum within the experimental range of the independent variables.
The experiment (Table 2) was based on the central composite design 11) and consisted of a 2 × 2 (ramp rate × temperature) orthogonal design augmented by 5 replicates at the center point. Conditions at the center point were ramp rate = 10 ℃/min and temperature = 80℃. Repeat observations at the center point were used to estimate the experimental error.
A sequential procedure of collecting data, estimating polynomials, and checking the adequacy of the model was used. The method of least squares was used to estimate the parameters in the approximating polynomials. Minitab 15 (Minitab Inc., USA) was used to establish the experimental design and to test complex polynomials to model the data.
- 2.4. Analytical Methods
All measurements were duplicated, and the results given are mean values. The COD and solid concentrations were determined using standard methods. 13)
3. Results and Discussion
- 3.1. Disintegration and Solubilization Effect of Microwave Pretreatment
We hypothesized that microwave irradiation would disrupt the complex activated sludge floc structure and release extracellular and intracellular biopolymers such as proteins, carbohydrates, and lipids into the soluble phase, and that it would enhance the solubilization of organic particulate matter. 14,15) The degree of solubilization of the substrate can be estimated from the SCOD to TCOD ratio (SCOD/TCOD, %). SCOD/ TCOD values in the pretreated sludge were clearly higher than that in the raw sludge ( Tables 1 and 2 ), thereby indicating that microwave irradiation had a strong effect on sludge solubilization. 16)
In Trial 8 (ramp rate = 10 ℃/min; temperature = 108℃), SCOD/TCOD (14.7%) was the highest among the 13 trials (Table 2) . The SCOD concentration increased from 379 ± 4 mg/L to 1,930 ± 143 mg/L and SCOD/TCOD increased from 2.6% to 14.7% (Table 2) in Trial 8; these values are comparable with the results of other studies. 14,15,17-20) At a given temperature, SCOD/TCOD increased as ramp rate decreased (Table 2) . 15,18)
Comparison of SCOD/TCOD gives a general indication of the extent of hydrolysis. In this study, SCOD/TCOD increased from 2.6% (control) to 3.3-14.7% after microwave pretreatment to 52-108°C. Solubilization of sewage sludge due to microwave irradiation has been previously reported; depending on conditions, reported SCOD/TCOD after microwave pretreatment temperatures (50℃ to 175℃) have ranged from 12% to 35%. 14,15,17-20)
- 3.2. Response Surface for the Solubilization of Sewage Sludge by Microwave Irradiation
A total of 13 trials, including a center point, were run to approximate the response surface for the solubilization of sludge by microwave irradiation (Table 2) . First, 9 trials were run. A first-order model, η i = β 0 + β x1 + β x2 , was attempted to fit the data by least squares and the following model (equation 1) was obtained.
PPT Slide
Lager Image
where η = experimental value of the solubilization degree (SCOD /TCOD, %), and x i = independent variable i ( i = 1 for ramp rate, and 2 for temperature).
When the data analyzed using the model, equation 1 was significant ( p < 0.01), while lack of fit was significant ( p < 0.05). Therefore, it was concluded that the first-order model was not an adequate approximation for the solubilization of sludge.
Additional trials were conducted to locate the maximum conditions for the solubilization more precisely. A second-order model could not be fit using the data from Trials 1 to 5 in Table 2 due to the lack of axial data points. An additional 4 trials (from Trials 6 to 9 in Table 2 ) were augmented with previous trials to make a central composite design.
To find the maximum solubilization degree of the sludge, increasingly complex equations from linear to quadratic were sequentially tested with theses augmented trials. Equations 2-4 represent linear, interaction, and quadratic models, respectively:
PPT Slide
Lager Image
PPT Slide
Lager Image
PPT Slide
Lager Image
Lack of fit was not significant ( p > 0.05) and regression was significant ( p < 0.01) for all models but the residual plot was randomly distributed without any pattern only for the quadratic model (data not shown). Therefore, the quadratic model was selected to describe the response surface of the solubilization degree of sludge within this region.
An analysis of variance using equation 4 was initially performed to investigate the possible interaction between variables (Table 3) . The interaction between the variables, ramp rate × temperature, was not significant ( p > 0.05). This meant that the independent variables were not interdependent. Further statistical inspection after excluding the interaction term showed that the ramp rate × ramp rate was not significant ( p > 0.05). Therefore, another quadratic model excluding the terms of ramp rate × temperature and ramp rate × ramp rate was used to describe the response surface of the solubilization degree of sludge and was
Analysis of variance for linear and square variables and their interaction
PPT Slide
Lager Image
Analysis of variance for linear and square variables and their interaction
PPT Slide
Lager Image
Equation 5 was highly significant ( p < 0.01; r 2 = 0.90) and showed no patterns or trends in residual plots (Fig. 2) , and lack of fit was not significant ( p > 0.05). All terms in equation 5 were significant ( p < 0.05). This results indicates that both ramp rate and temperature affect the level of solubilization. 15) Therefore, this equation was used to determine the conditions that would maximize the solubilization degree of sludge. Within the design boundaries, equation 5 estimated a maximum solubilization degree of sludge (15.8%) at 2.9 ℃/min and 104℃.
PPT Slide
Lager Image
Residual plots of the quadratic model (equation 5) for solubilization degree of sludge.
Two- and three-dimensional response surfaces of the quadratic model for the solubilization degree of sludge (Fig. 3) showed that the optimum condition was inside the design boundary only for temperature. At all temperature within the design boundaries SCOD/TCOD increased constantly as ramp rate decreased.
4. Conclusions
PPT Slide
Lager Image
Two- and three-dimensional contour plots of the quadratic model for solubilization degree of sludge (equation 5) with respect to pretreatment conditions of ramp rate and temperature within the design boundaries.
RSA was successfully applied to determine the effects of ramp rate and terminal temperature on the solubilization degree of sewage sludge and to estimate the response surface describing the solubilization degree to changes in these variables. In the model, both ramp rate and temperature affected the solubilization degree significantly ( p < 0.05). Within the design boundaries, maximum solubilization degree occurred at a ramp rate of 2.9 ℃/min and a terminal temperature of 104℃.
This study was supported in part by the Korean Institute of Environmental Science and Technology (EcoTechnopia-21 project) and by 2007 Research Grant from Kangwon National University.
Weemaes Marjoleine P. J , Verstraete Willy H 1998 Evaluation of current wet sludge disintegration techniques Journal of Chemical Technology & Biotechnology 73 (2) 83 - 92
Baier U , Schmidheiny P 1997 Enhanced anaerobic degradation of mechanically disintegrated sludge Water Science & Technology 36 (11) 137 - 143
Weemaes M , Grootaerd H , Simoens F , Verstraete W 2000 Anaerobic digestion of ozonized biosolids Water Research 34 (8) 2330 - 2336
Tiehm A , Nickel K , Zellhorn M , Neis U 2001 Ultrasonic waste activated sludge disintegration for improving anaerobic stabilization Water Research 35 (8) 2003 - 2009
Madigan M.T , Martinko J.M , Dunlap P.V , Clark D.P 2005 Biology of microorganisms 11th ed Benjamin Cummings
Oh S.E 2006 Improvement of anaerobic digestion rate of biosolids in waste activated sludge (WAS) by ultrasonic pretreatment Environ Eng Res 11 (3) 143 - 148
Tanaka S , Kobayashi T , Kamiyama K.-i , Signey Bildan M.L.N 1997 Effects of thermochemical pretreatment on the anaerobic digestion of waste activated sludge Water Science & Technology 35 (8) 209 - 215
Hong S.M , Park J.K , Lee Y.O 2004 Mechanisms of microwave irradiation involved in the destruction of fecal coliforms from biosolids Water Research 38 (6) 1615 - 1625
Jones D.A , Lelyveld T.P , Mavrofidis S.D , Kingman S.W , Miles N.J 2002 Microwave heating applications in environmental engineering-a review Resources Conservation and Recycling 34 (2) 75 - 90
Woo I.S , Rhee I.K , Park H.D 2000 Differential damage in bacterial cells by microwave radiation on the basis of cell wall structure Applied and Environmental Microbiology 66 (5) 2243 - 2247
Myers R.H , Montgomery D.C 2002 Response surface methodology: Process and product optimization using designed experiments 2nd ed John Wiley and Sons Inc New York
Wang S , Chen F , Wu J , Wang Z , Liao X , Hu X 2007 Optimization of pectin extraction assisted by microwave from apple pomace using response surface methodology Journal of Food Engineering 78 (2) 693 - 700
APHA;AWWA;WEF 2005 Standard methods for the examination of water and wastewater 21st ed American PublicHealth Association Washington DC
Eskicioglu C , Kennedy K.J , Droste R.L 2006 Characterization of soluble organic matter of waste activated sludge before and after thermal pretreatment Water Research 40 (20) 3725 - 3736
Eskicioglu C , Terzian N , Kennedy K.J , Droste R.L , Hamoda M 2007 Athermal microwave effects for enhancing digestibility of waste activated sludge Water Research 41 (11) 2457 - 2466
Hong S.M 2002 Enhancement of pathogen destruction and anaerobic digestibility using microwaves Ph D thesis
Hong Seung M , Park Jae K , Teeradej N , Lee Y O , Cho Y K , Park C H 2006 Pretreatment of sludge with microwaves for pathogen destruction and improved anaerobic digestion performance Water Environment Research 78 (1) 76 - 83
Eskicioglu C , Kennedy K J , Droste R L 2008 Initial examination of microwave pretreatment on primary secondary and mixed sludges before and after anaerobic digestion Water Science & Technology 57 (3) 311 - 317
Eskicioglu C , Kennedy K. J , Droste R. L 2007 Enhancement of Batch Waste Activated Sludge Digestion by Microwave Pretreatment Water Environment Research 79 (11) 2304 - 2317
Park B , Ahn J.H , Kim J , Hwang S 2004 Use of microwave pretreatment for enhanced anaerobiosis of secondary sludge Water Sci Technol 50 (9) 17 - 23