Advanced
Genetic Algorithm Based Design Optimization of a Six Phase Induction Motor
Genetic Algorithm Based Design Optimization of a Six Phase Induction Motor
Journal of Electrical Engineering and Technology. 2015. May, 10(3): 1007-1014
Copyright © 2015, The Korean Institute of Electrical Engineers
This is an Open-Access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/3.0/)which permits unrestricted non-commercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
  • Received : July 31, 2014
  • Accepted : December 27, 2014
  • Published : May 01, 2015
Download
PDF
e-PUB
PubReader
PPT
Export by style
Article
Author
Metrics
Cited by
TagCloud
About the Authors
Z. Fazlipour
Corresponding Author: Dept. of Electrical and Electronic Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran. (eng.zahrafazlipour@gmail.com)
R. Kianinezhad
Dept. of Electrical and Electronic Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran. ({reza.kiani, m_razaz}@scu.ac.ir)
M. Razaz
Dept. of Electrical and Electronic Engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran. ({reza.kiani, m_razaz}@scu.ac.ir)

Abstract
An optimally designed six-phase induction motor (6PIM) is compared with an initial design induction motor having the same ratings. The Genetic Algorithm (GA) method is used for optimization and multi objective function is considered. Comparison of the optimum design with the initial design reveals that better performance can be obtained by a simple optimization method. Also in this paper each design of 6PIM, is simulated by MAXWELL_2D. The obtained simulation results are compared in order to find the most suitable solution for the specified application, considering the influence of each design upon the motor performance. Construction a 6PIM based on the information obtained from GA method has been done. Quality parameters of the designed motors, such as: efficiency, power losses and power factor measured and optimal design has been evaluated. Laboratory tests have proven the correctness of optimal design.
Keywords
1. Introduction
In early 1990s, study on multiphase electric machines accelerated; until the beginning of recent century, it became practical in industries. Multiphase induction motors are predominantly used in electric ship propulsion, traction and generally in high power applications [1 - 3] . Multiphase induction motors have some advantages over three phase induction motors. Employing multi-phase induction motors would reduce the pulsating torque and would increase the efficiency of the machine. 6PIM reduces 6.7% stator copper losses compared to the same equivalent three-phase [4 - 5] . Also, multiphase induction motors have less noise pollution compared to three-phase ones [6] . Among several benefits, more phases provide better performance following loss of one or more phases; in addition multiphase motors can start and run even with some phases open circuit [7 - 10] . The other advantage is the improvement of torque in multiphase motors with concentrated winding [11] . Actually 6PIM is produced based on the reconfiguration of an existing three phase induction motor. The aim of this paper is to introduce a new idea in producing 6PIM. A design package has been developed specifically for a 6PIM. Then GA is used for the optimization process. The procedure is based on the basic electromagnetic equations, GA based optimization and checking the results by FEM. The FEM used in this work is based on the MAXWELL_2D software. The GA optimization method is described in the next section. The third section presents the 6PIM design. In section four, the 2-D Complex Eddy-Current Model will be introduced. Design program, objective functions and constraints are proposed in section five. Simulation and experimental results are presented in sections six and seven respectively. Finally some discussions and conclusions are presented in the last sections.
2. GA optimization method
In the most general sense, GA-based optimization is a stochastic search method that involves the random generation of potential design solutions and then systematically evaluates and refines the solutions until a stopping criterion is met. Genetic algorithm that produces good results in many practical problems is composed of the following three operators [12] : Selection: Selection is a process in which individual strings are selected according to their fitness. The selection probability can be defined by [12] :
PPT Slide
Lager Image
Where Pj is the selection probability and F ( xi ) is the objective function of the string xi. Crossover: This is the most powerful genetic operator. One of commonly used methods for crossover is the single-point crossover. As shown in the following example, a crossover point is selected between the first and the last bits of the chromosome, then binary code of the right of the crossover point of chromosome1 goes to offspring2 and chromosome2 passes its code to offspring1. This operation takes place with a defined probability Pc that statistically represents the number of individuals involved in the crossover process.
  • Chromosome1=0010010|101 offspring1=0010010|100
  • Chromosome2=0101011|100 offspring2=0101011|101
Mutation: This is a common genetic manipulation operator, and it involves, the random alteration of genes during the process of copying a chromosome from one generation to the next. Raising the ratio of mutations increases the algorithm’s freedom to search outside of the current region of parameter space. Mutation changes from a “1” to a “0” or vice versa. It may be illustrated as follows.
110000010 110001010
The genetic algorithm implementation steps are shown as follows [12] :
  • Step 1: Define parameter and fitness function (initializing)
  • Step 2: Generate first population randomly
  • Step 3: Evaluate population by objective function
  • Step 4: Applying GA operators (selection, crossover, mutation)
  • Step 5: Evaluate new population
  • Step 6: Reproduction process, create new generation.
  • Step 7: Test convergence. If satisfied stop else continue.
The calculated values are checked in order to satisfy the constraints.
3. 6PIM design
The traditional design approach was established nearly half a century ago and is dominated by rules of thumb and empirical curves that reflect the experiences of manufacturers, sometimes passed down from generation to generation as the established “company policy” way of doing it. In the traditional design, designers start by heuristically selecting values of design parameters, and then follow an iterative tuning process trying to achieve design specifications.
- 3.1The sizing equation
Traditional electric machine design usually starts from the famous sizing equation [14] , as follows
PPT Slide
Lager Image
Where S is the motor rating in Watt, Bav is the specific magnetic loading in Tesla, ac is the specific electrical loading in A/m, D is the stator inner diameter in mm, L is the motor active length in mm, Kw1 is the winding factor, and n is the rated speed in r. p. s (revolutions per second). Values for Bav and ac are selected by the designer at the start of the design process. The magnetic loading Bav is limited by the saturation point of the materials used, the hysteresis losses, the eddy current losses, the stray losses, the effectiveness of the cooling strategy, the load profile, and the duty cycle. The specific electric loading ac is limited by the copper loss in the conductors, the effectiveness of the cooling strategy, the temperature limitation of the insulation material, the load profile, and the duty cycle. In the traditional design, the selection of Bav and ac is primarily based on the designer’s experience [13] .
- 3.2 Selection of the aspect ratio
After B and ac are selected, the D2L value of the machine is then calculated by (2). For a machine with its pole number denoted by p , an aspect ratio λ is defined as
PPT Slide
Lager Image
Y is the pole pitch in meters. By choosing a proper value for λ , D and L can be then calculated. Besides Bav and ac , λ is another design parameter that designers usually choose at the beginning of the design process. A good choice of λ helps to increase winding induced EMF with less coil length. With the same flux density, the induced EMF is proportional to the coil area [13] .
- 3.3 Selection of current density
By selecting values for Bav , ac and λ , another important design parameter to select is the stator current density Js . For a certain rated current I , the current density Js determines the cross sectional area of the used copper wire Awire , as shown in (4)
PPT Slide
Lager Image
Higher current density leads to smaller Awire and then greater armature resistance. For the same stator current, the copper loss is increased. This higher copper loss not only leads to lower machine efficiency, but also increases the winding operating temperature because more heat is generated. In the traditional design, the current density is typically selected by rule of thumb or the designer’s experience. According to certain empirical rules, the current density is generally selected in the range of 3 to 7 A/mm2 [13 , 14] .
- 3.4 Selection of the flux density
To fully utilize the material, the flux densities in the teeth and cores are usually selected around the knee point of the B - H curve. The traditional design rules were mostly developed based on silicon steel with a knee point flux density around 1.5 T [12] .
- 3.5 Electrical machine design process
The traditional electrical machine design process is an iterative process and is summarized by the flow chart in Fig. 1 . An a priori, assumption of machine efficiency effa and power factor pfa have to be made and the machine rating S in VA is calculated by (5),
PPT Slide
Lager Image
PPT Slide
Lager Image
Illustration of the iterative design process in the traditional machine
Where Pout is the specified machine rated output power. After the value for S is calculated, values for Bav , ac and λ are selected to calculate D and L according to the sizing equation (2). Then, with the given rated voltage and current density, the number of coil turns and wire diameter of stator winding coils are determined for a given winding layout. At the same time, tooth width and core thickness are calculated with the selection of the flux density in the teeth and the core. The machine’s outer diameter is then calculated from the slot area needed for the winding and the areas of the teeth and core. Rotor designs are also carried out with certain traditional rules, which can be found in the literature, such as [13] . After one complete trial design is produced, the performance of this trial design is calculated and verified against initially selected design parameters (primarily Bav , ac , and Js ) and a priori assumptions of efficiency and power factor. If any of these parameters does not agree with initially assumed values, modifications are made to either design parameters or a priori assumptions and the design process is repeated. This process is repeated as many times as needed until agreement is reached. Even if such agreement is achieved, there are also various performance requirements to meet, such as specified maximum winding temperature, minimum power factor, and maximum weight. For line start induction machines, there are also requirements about starting current and starting torque.
- 4. 2-D Complex Eddy-Current Model
When eddy-current is considered, the Maxwell equations can be applied to the 2-D domains to give the following equation [15] :
PPT Slide
Lager Image
σ is the conductivity of material. If the model is linear, the magnetic source and the magnetic field will change sinusoidally with time. Hence J and A are sinusoidal vectors, and ∂A/∂t can be represented by jωA . Moreover,
PPT Slide
Lager Image
B is the magnetic flux density and H is the magnetic field strength [15] .
5. Design Program, Objective Function and Constraints
Programs written in MATLAB m. file have been tested for the problem under consideration. The program modified the initial values in suitable steps, evaluated the parameters of 6PIM, and retained the values if the constraints are not violated program. However, the design program has been developed, based upon the recommendations of the various references [13 , 16 , 17] . The design optimization of electric motor requires a particular attention in the choice of the objective function that usually concerns performance features. This problem is represented by the multi objective approach. Then, we have considered the following multi objective formulations [14] :
1. To optimize the stator copper loss
PPT Slide
Lager Image
Where Iph is the phase current in Amps and RS is stator resistance in Ohms.
2. To optimize the rotor copper loss
PPT Slide
Lager Image
Where rr is constant (0.021), S2 is the number of rotor slots and Ib is rotor bar current in Amps, De is mean end ring diameter in mm, Lr is length of the core in m and P is the number of poles.
3. To optimize the stator iron loss
PPT Slide
Lager Image
Where Wt is weight of the stator teeth, Wc is weight of the stator core, Wtk is losses in stator tooth portion W/kg, Wck is losses in stator core W/kg.
4. Full load efficiency
PPT Slide
Lager Image
Where PO is power in KW, PSCL is stator copper loss in W , PRCL is rotor copper loss in W, PSIL is stator iron losses in W, PF is friction losses in W. To obtain a desirable performance, the constraints such as, starting current, starting torque, etc. are imposed on the optimization process. As shown in Fig. 2 quantities chosen as the principal motor variables for the optimization consist of the following five parameters: Core length (equal for rotor and stator) (x 1 ), stator inner diameter (x 2 ), depth of stator slot (x 3 ), width of stator teeth (x 4 ),depth of stator core (x 5 ). The motor with the nominal ratings, shown in Table 1 , is chosen for optimization.
PPT Slide
Lager Image
Optimization variables
6PIM Characteristics
PPT Slide
Lager Image
6PIM Characteristics
5. Genetic Algorithm Optimization Results
The flow chart of the design optimization procedure is depicted in Fig. 3 . Each block consists of number of subroutines. The execution of the program starts with the performance specifications such as the initial motor design variables, the number of generations, population size, crossover rate, and mutation rate. Number of generations, crossover rate and mutation rate can be selected depending on the user. Each design parameter and penalty limit for penalty function can be varied within its domain. Then design parameters of the stator and rotor layout are calculated. The optimization constraints are as follows:
PPT Slide
Lager Image
Flow chart for design optimization process
Minimum power factor 0.79, maximum starting current 7.5 (p. u), minimum starting torque 2 (p. u), maximum flux density in stator and rotor core and teeth around 1.5 T, no load power factor between 0.15 and 0.28. Table 3 presents parameters of GA program and Table 4 summarizes the output of the optimized Genetic Algorithm 6PIM design. Some discrepancies appear between the initial design and optimum design results are shown in Table 2 and Table 4 . As shown in Tables 2 and 4 , starting torque of the GA based design is 4.5898 (p. u), that greater than initial design and therefore, it exhibits a better performance for greater loads. Also as it can be seen in Tables 2 and 4 starting current of the GA based design is 5.7853(p. u), that higher than initial design due to the lower equivalent resistances of the motor and so, the temperature rise in the motor will be lower at the rated load.
The output summery of the initial design of 6PIM (INI)
PPT Slide
Lager Image
The output summery of the initial design of 6PIM (INI)
Parameter of GA Program
PPT Slide
Lager Image
Parameter of GA Program
The output summery of the initial design of 6PIM
PPT Slide
Lager Image
The output summery of the initial design of 6PIM
Figs. 4 , 5 show the flux density distribution for the motor. According to results that shown in Tables 2 and 4 , optimized 6PIM has higher stator stack length and stator inner diameter than initial 6PIM so has greater flux in each pole. Table 5 shows the calculated and the finite element amount of flux densities in initial and optimized 6PIM are in relatively good agreement considering the required simplifications in the analytical design algorithms. The ratio of stator inner diameter to width of the stator tooth in GA based design is lower than initial design, so maximum flux density in optimized design is lower than flux density in initial design. As be seen maximum flux density in stator teeth is 1.004 T and mean flux density in stator core is 0.81312 T for GA based design and FEA result shows that these flux density specifications are achieved correctly. According to Figs. 4 , 5 and results shown in Table 5 , flux densities in stator core and teeth of initial design and GA based optimization design are around 1.5 T, so both of these motors are working in knee point correctly.
PPT Slide
Lager Image
Flux and flux density distribution (Initial design)
PPT Slide
Lager Image
Flux density distribution (GA design)
Electromagnetic parameters of initial (INI) and GA optimized design (GA) of 6PIM
PPT Slide
Lager Image
Electromagnetic parameters of initial (INI) and GA optimized design (GA) of 6PIM
6. Experimental Results
As design aspects of Genetic Algorithm optimization are closer to the standard electric motor forms, construction of the 6PIM based on information obtained from this optimized design has been done. Fig. 6 shows manufacturing process of 6PIM. Tests results of constructed motor are presented in Table 5 and Table 6 . As can be seen, the only major difference is the equivalent reactance, which may be due to differences in the dimensions considered in the design of the rotor to be used but it will not have much impact on the efficiency and motor losses. It makes improvement in motor performance, because the increase in impedance value causes a reduction in the start current and the short circuit power factor and all of these reasons cause improvement in motor performance. To verify 6PIM under load condition, a 300 W, 220 V, 1.8 Amp, DC generator coupled with the made 6PIM. Fig. 7 shows 6PIM under load condition. Results of 6PIM test under load are represented in Table 7 .
No load, locked rotor and DC test results of constructed 6PIM
PPT Slide
Lager Image
No load, locked rotor and DC test results of constructed 6PIM
Results of 6PIM test under load condition
PPT Slide
Lager Image
Results of 6PIM test under load condition
PPT Slide
Lager Image
6PIM manufacturing process
PPT Slide
Lager Image
Constructed 6PIM coupled with DC generator
Two most important characteristics that we were interested in are torque-speed and current-speed curves (which is) represented in Fig. 8 . Fig. 9 shows variations of performance characteristics with phase voltage at nominal load. In order to compare the simulation results and experimental results from optimized constructed 6PIM, each performance characteristic of initial, GA based optimization and constructed 6PIM is given in one figure. Reduction of s corresponds to the reduction of the rotor current (Pm constant) and input current. It can reduce the major Ohmic loss of the motor, and efficiency will be higher. With comparison of results shown in Figs. 9 (a , b) and Table 2 , 4 , slip at rated voltage in optimized and constructed 6PIM is smaller than initial design so GA based design improved efficiency around 5% at rated voltage. Slight differences between numerical and experimental results in start torque and start current because of probable error in stator resistance measure and so differences in equivalent resistance and equivalent reactance are acceptable.
PPT Slide
Lager Image
(a) Torque-speed and (b) current-speed characteristics
PPT Slide
Lager Image
(a) Variation of slip with phase voltage at nominal load and (b) Variation of efficiency with phase voltage at nominal load and
6. Conclusion
As can be seen obtained output power from constructed optimal motor is 238.625w which is very close to the predicted value from optimum design and the error is negligible. So accuracy of optimal design of GA has been proven by experimental results. This paper introduced a new approach in designing 6PIM. A 0.26Kw motor has been designed and constructed. According to studies, the following results are obtained:
  • Comparison of the final optimum design with the initial design indicates that the gain of the proposed performance is even better than expected. In this instance, a higher starting torques and finally a greater efficiency (with respect to the corresponding constraints) for an optimum design of 6PIM can be noted. The Genetic Algorithm optimum design improves efficiency around 5%.
  • Variations of performance characteristics (in %) of the optimum designs with phase voltage is rather low compared to the initial design.
  • The calculated and the finite element flux densities in the motor are in relatively good agreement considering the required simplifications in the analytical design algorithms.
  • Construction a 6PIM based on information obtained from GA method has been done. Quality parameters of the designed motors, such as: efficiency, power loss and power factor, measured and optimal design has been evaluated. Laboratory tests have proven the correctness of optimal design.
BIO
Zahra Fazlipour She was born in Ahvaz, Iran, in 1989. She received B.S degree in electrical engineering from Shahrekord University at Shahrekord, in Iran in 2012 and the M.Sc. degree in electrical power engineering from Shahid Chamran University of Ahvaz, Iran, in 2014. Her research interests are power electronic and electrical machine design.
Reza Kianinezhad He was born in Ahvaz, Iran, in 1963. He received the B.Sc. degree in electrical engineering from Shahid Chamran University of Ahvaz, in 1988, the M.Sc. degree in electrical power engineering from Tarbiyat Modares University, Tehran, Iran, in 1995, and the Ph.D. degree from the University of Picardie Jules-Verne, Amiens, France, in 2006. Currently, he is with the Department of Electrical Engineering at Shahid Chamran University, Ahvaz, Iran. His research interest is modeling and control of multiphase induction machines.
Morteza Razaz He was born in Dezful, Iran, in 1948. He received BS and MS degrees in Electrical Engineering and Applied Mathematics from Texas University, USA, in 1977 and 1979, respectively, and a PhD degree from Sharob University, UK, in 1993. Currently, he is with the Department of Electrical Engineering at Shahid Chamran University, Ahvaz, Iran. His research interests include power electronics, protection relay, and electric machinery.
References
Singh G.K. 2002 “Multi-phase induction machine drive research – a survey” Electric Power Systems Research 61 (2) 139 - 147
Hodge C. , Williamson S. , Smith A.C. 2002 “Direct drive marine propulsion motors” Belgium ICEM Proc. Int. Conf. on Electrical Machines
Levi E. 2008 “Multiphase electric machines for variable-speed applications” IEEE Transactions on Industrial Electronics 55 (5) 1893 - 1909
Apsley J.M. , Williamson S. , Smith A.C. , Barnes M. 2006 “Induction motor performance as a function of phase number” IEE Proc.-Electric Power Applications 153 (6)
Williamson S. , Smith A.C. 2003 “Pulsating torque and losses in multiphase induction machines” IEEE Transactions on Industry Applications 39 (4) 986 - 993
Apsley J. M. , Williamson S. , Smith A. C. , Barnes M. 2006 “Induction motor performance as a function of phase number” Proc. IET 153 (6) 898 - 904
Toliyat H.A. 1998 “Analysis and simulation of five-phase variable-speed induction motor drives under asym-metrical connections” IEEE Transactions on Power Electronics 13 (4) 748 - 756
Fu Jen-Ren , Lipo T.A. 1994 “Disturbance-free operation of a multiphase current-regulated motor drive with an opened phase” IEEE Transactions on Industry Applications 30 (5) 1267 - 1274
Smith A. C. , Williamson S. , Hodge C. G. 2003 “High torque dense naval propulsion motors” EMDC Proc. IEEE International Electric Machines and Drives Conf 3 1421 - 1427
Kianinezhad R. , Nahidmobarakeh B. , Baghli L. , Betin F. , Capolino G. A. 2008 Modeling and control of six-phase symmetrical induction machines under fault condition due to open phases IEEE Trans. Ind. Electron 55 (5) 1966 - 1977
Lyra R.O.C. , Lipo T.A. “Torque density improvement in a six-phase induction motor with third harmonic current injection” IEEE Transactions on Industry Applications 38 (5) 1351 - 1360
Goldberg D.E. 1989 Genetic Algorithms in Search, Optimisation, and Machine Learning Addison Wesley NewYork
Mittle V. N. 1996 Design of Electrical Machine 321 - 404
Say M. G. 1970 Performance and design of AC machines: Pitman London
Chrari. M.V.K. 1974 “Finite element solution of eddycurrent problem in magnetic structure” The transactions of Institute of Electrical and Electronics Engineers on Power Apparatus and Systems 93 62 - 72
Ramamoorty M 1988 Computer aided design of electrical equipment Wiley Chichester, UK.
Sivaraju S. S. , Devarajan N. 2011 “Novel Design of Three Phase Induction Motor Enhancing Efficiency, Maximizing Power Factor and Minimizing Losses” European Journal of Scientific Research 58